Тёмный

{782} 12 Volt SMPS Has Only 3 Volt Output, Low Output 

Haseeb Electronics
Подписаться 125 тыс.
Просмотров 91 тыс.
50% 1

12 Volt SMPS Power Supply Has Only 3 Volt Output. in this video number {782} i demonstrated and explained how to repair TL494 / KA7500 based half bridge 12 volt 20 ampere smps rafeed model RF-0076, it was providing low output voltage than the rated 12 volt, and there was no control by voltage adjustment potentiometer. i found the pwm controller ic tl494, it was damaged. i replaced the smps controller ic with new one and the power supply started functioning normally
You are Invited to Join Haseeb Electronics
/ @haseebelectronics
how to fixed switch mode power supply SMPS step by step when OutPut Voltage Low
How To Repair Switch Mode Power Supply when the output voltage are less than the rated voltage and it is giving unregulated voltage
How To Repair Switch Mode Power Supply SMPS, When it have low OutPut Voltage
how to repair tl494 half bridge topology power supply circuit,
practical repair of 12 volt 20 amp switch mode power supply SMPS.
after watching this video you can capable to:-
how to repair smps
if SMPS have low output or output voltage unregulated
how to repair computer power supply
how to repair laptop charger
#smps #low #output
i shared very easy & step by step practical troubleshooting / circuit tracing and fault finding techniques to find the faults in any switching mode power supply.
how to repair smps (switch /switching mode power supply), either it is industrial power supply, laptop charger, adapter, computer atx power supply, server power supply, mobile charger, battery charger, inverter welding machine, led / lcd tv power supply, power supply of dth / digital satellite receiver,
how to repair smps (switch / switching mode power supplies) in very easy step by step repair and practical troubleshooting & circuit tracing tutorial
12 Volt Power Supply Have Only 3 Volt Output, how to repair smps, switch mode power supply, very easy repair of SMPS, haseeb electronics, smps output fluctuating, SMPS OutPut Voltage Low, smps repair, smps low output voltage problem, smps repair step by step, switching power supply repair, 12 volt power supply, 12 volt 20 amp power supply, 12 volt 20 amp smps, tl494 smps, tl494 smps circuit, tl494 smps power supply, pwm tl494 smps, smps have 3 volt
00:00 12 volt smps power supply is giving low output voltage
00:30 how to apply power to a circuit for testing (DUT / UUT)
00:49 how to troubleshoot / repair smps power supply
04:47 damaged / cracked TL494 ic
05:07 how to check TL494 power supply circuit

Наука

Опубликовано:

 

28 июн 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 253   
@electroniquepassion
@electroniquepassion Год назад
good repair 👍👏👋
@HaseebElectronics
@HaseebElectronics Год назад
best regards dear friend
@German_byte
@German_byte Год назад
I did enjoy the video. I like how you start off with a careful visual inspection of the components and then zero in on the likely culprits. A very satisfying repair.
@tonyrebeiro
@tonyrebeiro Год назад
Just one small observation about your logic regarding the soldering of random legs of the IC. Your logic and technical aspect is fine but all these mass produced cards are usually, Wave Soldered in the factory, which means all the legs of the IC are soldered at one go. From what I know, standard quality electronic components are designed to withstand this heat, without getting damaged. Otherwise, your videos are very informative and useful. Thank you.
@HaseebElectronics
@HaseebElectronics Год назад
absolutely perfect dear at factory the soldering temperature and soldering time are predefined and set properly, either for manual soldering or automatic soldering but in the field there is no temperature controlled seldering iron and not too expert soldering person even in my department my subordinate engineers and technicians most of time damage ics by unconcontrolled temperature soldering iron and soldering time, and in line soldering so in my experience it is best idea to solder or desolder randomly
@HaseebElectronics
@HaseebElectronics Год назад
please accept my best regards and special thanks for your kind observation
@W1RMD
@W1RMD Год назад
Great video! The old IC you pulled out looked counterfeit. The shape of Texas was more fat and round and the "I" was not clear. The new one that you installed had a definite clear shape of Texas with a definitive letter "I". Thanks for sharing sir!
@HaseebElectronics
@HaseebElectronics Год назад
best regards most of time the ics have logos but these are not real as most of the components are being manufactured in china, so brand and quality cannot be certified just part number is printed
@KylaJay243
@KylaJay243 Год назад
Hi Sir, thank you for sharing your knowledge and skills about electronics troubleshooting and repairing, many people who are interested in electronics like me have learned from your videos. I learned a lot from your tutorial videos. In fact I really understood very well how a SMPS woks. Keep up the good work and looking forward to the next tutorial video. More power to you sir. Mabuhay....
@gordonlovett71
@gordonlovett71 Год назад
You da man, keep the videos coming. Very educational
@Simon-mz7sf
@Simon-mz7sf Год назад
Gday great presentation. Liked how you made sure other components were in good shape before replacing the IC. I always learn something from you.
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@jluke6861
@jluke6861 Год назад
You explain things so good. And you are good at what you do. Thank you for taking time and making this video. Tbark Allah 3alik.
@HaseebElectronics
@HaseebElectronics Год назад
thanks a lot stay blessed
@NEKOTAROU-xj8jw
@NEKOTAROU-xj8jw Год назад
Nice to meet you, my name is NEKO🐱TAROU, a Japanese RU-vidr. I have the same PSU as you. When it breaks down, I will watch your video and try to fix it. Thank you for sharing the video. 👍 I subscribed to your channel. ❗
@HaseebElectronics
@HaseebElectronics Год назад
most welcome try to troubleshoot and if you find some difficulty. please let me know. i will try my best to sort out the problem wishing you best of luck and success
@ig_jr4843
@ig_jr4843 Год назад
Thank you !!! Best wishes from Brazil 👏👏
@HaseebElectronics
@HaseebElectronics Год назад
best regards 💕
@gmtoolman67
@gmtoolman67 Год назад
Hello sir , I love to watch and relearn from your vdos , your tip to desolder ICs in random order reminded me of my service instructor who use to reiterate the same thing and i used to repeat to my students .... Best regards
@santosnecesario1932
@santosnecesario1932 6 месяцев назад
I love watching your tutorial video, very helpful. Explanation is very clear. Thank you Sir!
@HaseebElectronics
@HaseebElectronics 6 месяцев назад
most welcome and special thanks
@sadunnakipoglu9471
@sadunnakipoglu9471 2 месяца назад
Thank you !!! Best wishes from Turkey
@HaseebElectronics
@HaseebElectronics 2 месяца назад
most welcome
@NikkisKitchenandVlog
@NikkisKitchenandVlog Год назад
Very informative thank u so much👌🏼
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@rul1175
@rul1175 Год назад
I really enjoy your videos. Thank you.
@HaseebElectronics
@HaseebElectronics Год назад
So nice of you
@platinumsteel6458
@platinumsteel6458 Год назад
Hi i love every single video you have produced. Always learn something new. But i am missing something is it possible you can show us how to verify and check components like the rectifiers, small round capacitors, and transistors in and out of circuit. maybe resistors as well.And show us what a good reading should be and what is a bad reading is thanks.
@jamespaterson7597
@jamespaterson7597 8 месяцев назад
very interesting haseeb thankyou
@hunti123
@hunti123 Год назад
Thank you, i have a very similar SMPS but instead of TL494 it has KA7500BD, but i had the same voltage and the same problem. Thanks!
@hichamtassi1753
@hichamtassi1753 Год назад
Very nice repair video !!
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@aasaan_islam
@aasaan_islam Год назад
Very nicely explained and demonstrated
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@williamsullivan9323
@williamsullivan9323 Год назад
great tip on soldering IC's
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@Edmorbus
@Edmorbus Год назад
Another excellent repair
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@RotacRepair
@RotacRepair Год назад
Sir, thank you for the IC soldering sequence tip.
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@rectify2003
@rectify2003 11 месяцев назад
Well done again 👍
@mrelectromaniac6886
@mrelectromaniac6886 2 месяца назад
Thanks.you explain very good.
@imranmehdi111
@imranmehdi111 Год назад
Very helpful video. Thanks for this video sir jee
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@vijayakumarkumar9190
@vijayakumarkumar9190 Год назад
Very good and useful information sir thanks for sharing this knowledge to us
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@HarlavanisPanagiotis
@HarlavanisPanagiotis Год назад
Wonderful video dear friend, have a happy Thursday ☺️
@HaseebElectronics
@HaseebElectronics Год назад
best regards and stay blessed
@mohammad45h
@mohammad45h Год назад
تشکر وسپاس جناب مهندس ممنون وهزاران لایک.....لطفا وحتما راجعب پمپ...و.. وکیوم وهویه مکنده لحیم وات ان توضیح دهید ممنونم..🙏🙏👌👌❤❤
@adiseshukumpati24
@adiseshukumpati24 Год назад
really enjoyed sir soldering/desoldering technique is useful
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@aqeelmajeed2759
@aqeelmajeed2759 Год назад
amazing my favorite teacher.
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@kuhanthamuthukumarana1158
@kuhanthamuthukumarana1158 Год назад
Very Interesting ,,,,,,, Good Teacher......Easy to understand.........Dear Sir ....What is best Bulb wattage for use series to power up MPCS to check....I mean 100w or 40W
@HaseebElectronics
@HaseebElectronics Год назад
best regards 50watt tungsten lamp is awesome for power supplies upto 100 watt. 60/100 watt lamp will good for 100-200 watt power supplies
@CinematicTouchProductions
@CinematicTouchProductions Год назад
Hello Mr Haseeb, my youtube teacher. I can watch your videos for hours and not tire, I have a question for you. Do you have a video that can teach us your youtube students how to follow traces from point to point from the various components on a PCB on different types of electronics, or can you make a video for us please, I am trying to learn but I get lost looking at all the lines and most times it is a bit frustrating for a beginner like me because I really want to understand where these traces from each component begin and end and I get lost, thank you teacher for being so professional in the way you teach us!
@rabihnasr7228
@rabihnasr7228 Год назад
Woow before you disassemble it i was thinking that the feedback is in problem thank you
@HaseebElectronics
@HaseebElectronics Год назад
yes brother everyday we have to learn something new
@gauripartapshanker9197
@gauripartapshanker9197 Год назад
Informative vedeo thank u so much.
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@jalal76
@jalal76 Год назад
Good job.....thanks 👍
@HaseebElectronics
@HaseebElectronics Год назад
best regards 💕
@Somanathan-hj7ge
@Somanathan-hj7ge 8 месяцев назад
Sir, perfect working in all respects.more over cleaning, very best, and checked each and every transistor, ic , capacitor etc,super job done.thorurouly repaired sir, the best, good 👍
@HaseebElectronics
@HaseebElectronics 8 месяцев назад
best regards
@anantalalsarkar3323
@anantalalsarkar3323 3 месяца назад
My dear Brother, I am now only 68yrs! Electronics is my hobby and for passing my liesure period! I fond of watching yours knowledgeable and informative videos like this in You Tube ! May.i expect a little but important help from you? I tried to make a transformer less circuit for 12volt to run a cooling fan (3"12v) with that ? But I have failed! Out put is coming 13.2volt DC ? But while I connect to load the volt shows 4.3 or less! resulting fan is moving very slow! I can't understand what is fault are there ! May be for low ampere or any other reason? I wd like to let you know there are no sufficient room to fix the SD transformer. Kindly help me to give a fruitful suggestion in this regard? I shall be highly grateful to you. My heartiest good wishes for all of your upcoming videos as well as your present video. Stay happy and good bye for the day. I will be awaiting for your reply.
@HaseebElectronics
@HaseebElectronics 3 месяца назад
Good afternoon sir. when you are using 3" 12V fan, it means it is DC fan. it needs more ameres and the transformerless power supply (volatge dropper circuit) can provide just in milliampers, that is causing to drop the volatge to 4.3 volt. it is better to use isolated transfomre based power supply having a safe limit for current capacity please accept my best regards
@AbdulMomenZargar60
@AbdulMomenZargar60 Год назад
Beautiful Video Big Thumbs Up # 532
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@nishanbamunuarachchi6597
@nishanbamunuarachchi6597 8 месяцев назад
I really appreciate your very detailed and accurate explanation. Many thanks dear . Can we check the vcc voltage without the ic ( before replacing the new ic) pls ?
@mansirrabiu7412
@mansirrabiu7412 Год назад
Jazakallahu khairan Bhai 🙏
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@kayulasalimu9180
@kayulasalimu9180 Год назад
You are good.would like you to so sort out more on inverter problems.
@ihyaululum2417
@ihyaululum2417 5 месяцев назад
I have the same problem, but mine is a computer power supply. thank you for the tricks given, maybe I also need to replace the pwm IC.
@HYTMUAE
@HYTMUAE Год назад
I watched most of ur videos .. ur explanation is amazing .. I wish you were my teacher at the University 😁
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@palwindersandhu2031
@palwindersandhu2031 Год назад
Thanks a lot........👏👍
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@cosmomcfarlane7697
@cosmomcfarlane7697 7 месяцев назад
Great love it
@francomongillo
@francomongillo 3 месяца назад
Bravissimo.
@heshamkatr2128
@heshamkatr2128 Год назад
Thx so much
@julianhilaire1762
@julianhilaire1762 Год назад
Hi Haseeb Can you make a video on the functions of an led/lcd tv t-icon board and how it function. Thanks on advance
@snhongo1
@snhongo1 Год назад
Great video
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@abbaselekberov9033
@abbaselekberov9033 Год назад
Hello 👍👍 thanks you, good man
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@pravinpadhiyar2
@pravinpadhiyar2 Год назад
Vary very nice video sir
@HaseebElectronics
@HaseebElectronics Год назад
thanks a lot brother
@AliRezaJoodi
@AliRezaJoodi Год назад
Hi Very Nice Thanks
@boopathinarasimman1348
@boopathinarasimman1348 5 месяцев назад
Very nice, 🌹thanks
@HaseebElectronics
@HaseebElectronics 5 месяцев назад
Welcome 😊
@user-qh5kb7rv7o
@user-qh5kb7rv7o Год назад
I did enjoy the video
@HaseebElectronics
@HaseebElectronics Год назад
thanks a lot
@hojjatzare2483
@hojjatzare2483 Год назад
that was perfect❤❤
@HaseebElectronics
@HaseebElectronics Год назад
thanks a lot
@ahoorapersia4698
@ahoorapersia4698 Год назад
Well done 👏✔👍👌
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@mtrltoolman
@mtrltoolman Год назад
جزاك الله خير
@HaseebElectronics
@HaseebElectronics Год назад
االله يسلمك و يسعدك
@xhonatankurti8515
@xhonatankurti8515 11 месяцев назад
Mashalla, thanks for the videos
@HaseebElectronics
@HaseebElectronics 11 месяцев назад
best regards 💕
@toomatomic793
@toomatomic793 3 месяца назад
Hvala za prijevod
@HaseebElectronics
@HaseebElectronics 3 месяца назад
zadovoljstvo mi je. ugodan dan
@dickschottky9406
@dickschottky9406 7 месяцев назад
Thanks!
@HaseebElectronics
@HaseebElectronics 7 месяцев назад
Thanks a lot for your valuable support 💕
@AbdulMomenZargar60
@AbdulMomenZargar60 Год назад
Salaam Bhai Sahib
@HaseebElectronics
@HaseebElectronics Год назад
wa alaikum salaam bhai Ji
@aminkhanone7627
@aminkhanone7627 Год назад
Amazing sir
@HaseebElectronics
@HaseebElectronics Год назад
most welcome
@erkanmaller9695
@erkanmaller9695 Год назад
👍🇹🇷🇹🇷🇹🇷👍Another great video..! We are waiting for your smps repair videos.. Greetings from TURKEY..
@HaseebElectronics
@HaseebElectronics Год назад
most welcome
@anasory3225
@anasory3225 Год назад
Very good sir
@HaseebElectronics
@HaseebElectronics Год назад
it is my pleasure
@vijayakarekar
@vijayakarekar Год назад
Very nice....
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@demontagemontage
@demontagemontage Месяц назад
اشكرك
@abdelilahelazhari1820
@abdelilahelazhari1820 Год назад
Thanks sir.
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks
@johnmac2680
@johnmac2680 Год назад
Very impressive
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@Amirkhan-lf6mc
@Amirkhan-lf6mc Месяц назад
Great ❤❤❤
@bisfal
@bisfal Год назад
Hi sir. Thanks for the videos. I don't understand how a bad ic tl494 can have its vcc input lowered. I thought the vcc will not affected.
@HaseebElectronics
@HaseebElectronics Год назад
best regards i think its internal regulator is damaged, which caused to pull down the vcc pin. so ic cannot start working
@bisfal
@bisfal Год назад
@@HaseebElectronics thank you very much.
@ranamanwarurdupoetry8990
@ranamanwarurdupoetry8990 Год назад
Nice sharing
@HaseebElectronics
@HaseebElectronics Год назад
thanks a lot
@GoutamDAS-ls1wb
@GoutamDAS-ls1wb Год назад
Haseeb, excellent video with great advice on how to desolder IC's. I was wondering why you needed to take the heat sinks off to do the testing??? Is there a way to test the transistors without desoldering them?
@MichaelKingsfordGray
@MichaelKingsfordGray Год назад
Not that is reliable.
@electronicshelpcare
@electronicshelpcare 11 месяцев назад
Good
@abulkalam4440
@abulkalam4440 Год назад
Thanks.
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@manoftheday1
@manoftheday1 Год назад
Good day sir , please can you do a video on how to calculate the output inductor of power supply using tl494 please.
@restorationtv168
@restorationtv168 11 месяцев назад
Good share❤❤❤
@HaseebElectronics
@HaseebElectronics 11 месяцев назад
best regards
@rashidm9396
@rashidm9396 Год назад
MashAllah great
@HaseebElectronics
@HaseebElectronics Год назад
الحمد للہ
@milanmakwana3883
@milanmakwana3883 Год назад
dear i am watch your video nicely explanation please let me know how aux supply of Control IC is getting
@richardphillips2405
@richardphillips2405 6 месяцев назад
Thank you for your video. I looked up the TL494 IC chip. I realized that I did not understand it's operation. Is it possible to trouble shoot a circuit like a power supply without totally understanding the operation of the circuit, but able to understand the basics of the circuit operation. For example, I know that the TL494 is the regulator IC. The crack on the TL494 would make you suspect that it is bad. I understand SMPS basics, but I don't totally understand the circuit operation. So, I consider this a learning challenge to understand how all of this works. If someone wanted me to fix a power supply. I probably would spend more time trying to understand how the circuit works than actually spending time on trouble shooting the circuit. Could you suggest any books or material that goes into the circuit operation of power supplies. Thank you again.
@shefqetkaralliu6816
@shefqetkaralliu6816 Год назад
Grazie 🙏⭐⭐⭐⭐⭐👍
@HaseebElectronics
@HaseebElectronics Год назад
best regards 💕
@Tsjoetenbille
@Tsjoetenbille Год назад
Hi Sir. Another excellent repair. Is there any reason for the soldering sequence of the IC? Is it better to solder pins opposite than side by side for overheating? Kind regards, Frederic.
@HaseebElectronics
@HaseebElectronics Год назад
it is best way to divide ic pins in four portions for example i have 16 pin ic first i will solder pin 1, then 5, then 9 and 13 then 2, 6, 10 & 14 then 3, 7, 10 & 15 at ast 4, 8, 12 & 16 so using this technique every last pin will get adequate cooling time
@siavasharash5448
@siavasharash5448 Год назад
Was a wear problem of tl494 Because it was oscillating and you got some dc voltages on output. Also you got voltage near 5 volt in 5 volt referance pin So If that crack was not exsist the ic would be the last component you suspect to damage
@HaseebElectronics
@HaseebElectronics Год назад
no it was TL494 failure initial low voltage are being provided from start up circuit, it is composed of using mosfet gate biasing circuit + pulse transformer secondary side. this start up circuit, operates the mosfets in conduction state, which cause a limited current in mosfets and the transformer, in result the limited current causes to produce low voltage, and also it provides vcc voltage to SMPS controller, and it can start IC, then ic will start to produce rated output and it starts voltage regulation
@velialici7980
@velialici7980 Год назад
Selâmün Aleyküm Çok güzel ,bazı videolarından istifade ettim, Teşekkür ederim. Senin yaptığın bu işleri Türkçe konuşan biri yapsa daha çok şey öğrenebilirdim. Maalesef ben Türkçe dışında başka bir dil de bilmiyorum. Alt yazı seçeneği ile değerlendirip biraz daha anlamaya çalışıyorum.
@HelgiThorisson
@HelgiThorisson Год назад
Very good video. How warm are your soldering irons in this video?
@HaseebElectronics
@HaseebElectronics Год назад
i use soldering iron at 380-410 degree centigrade desoldering tool 420-440 degree centigrade
@gopalarao8578
@gopalarao8578 Год назад
Hi sir...namaskaar. I like your working style. Which liquid is using to clean the pcb..? Thank you for the video. Good night 🙏
@HaseebElectronics
@HaseebElectronics Год назад
best regards and special thanks it is isopropyl alcohol technical alcohol or methylated spirit
@gopalarao8578
@gopalarao8578 Год назад
@@HaseebElectronics Thank you for your reply 🙏
@czirkosl
@czirkosl Год назад
It's very simple, VR1 voltage regulator trimmer 1 kohm is defective, try to 300 Ohm - 560 Ohm resistor. If I have made a shorcut for trimmer voltage became 13,5 V the output.
@somuduttamudi6384
@somuduttamudi6384 Год назад
Guruji very nicely explained 💯❤️❤️❤️❤️🙏🙏🙏🙏
@HaseebElectronics
@HaseebElectronics Год назад
best regards 💕
@HarvinderSingh-vs2yl
@HarvinderSingh-vs2yl 9 месяцев назад
Tadh desoldering pump bhout asha lagya
@BabarAli-qi9yo
@BabarAli-qi9yo 9 месяцев назад
Masha Allah
@aanishkadailydose
@aanishkadailydose Год назад
Aslmuailkum lk dn
@HaseebElectronics
@HaseebElectronics Год назад
wa alaikum salaam dear sister thanks a lot
@1fertube
@1fertube Год назад
Great! What liquid do you use to clean the board with the toothbrush? Thanks
@HaseebElectronics
@HaseebElectronics Год назад
it is technical alcohol isopropyl alcohol or methylated spirit
@nishanbamunuarachchi6597
@nishanbamunuarachchi6597 8 месяцев назад
Also do we get equal base bias voltage to the main 2 transistors in the start up section when there is no load ? pls clarify . Thanks
@green_life7
@green_life7 Год назад
I want to use smps for my garden lighting supply instead of AC for safety reasons. Will it be a good idea? I will run many 12v DC led bulbs. Also please tell why SMPS have many output connections? Should I club all connections into 1 set of 12v DC? Also please tell is there any chance that a SMPS gives AC output and give shock to anyone in the garden? If there is a chance, what to do? Should I use a fuse to avoid any mis-happening or is there any other method such as MCB? If yes, what should be the specifications of the fuse/mcb or other component?
@Prem_infogate
@Prem_infogate Год назад
I have a quick question. Is that pull the required ampere output such as 20A or 30A or 40A from 230v with a 6A/10A 3 pin? I am using a car amplifier at home which is maximum ampere rated as 35. To get a desired ampere output what should I do?
@hichamtassi1753
@hichamtassi1753 Год назад
Can you please explain how current control works ?
@SuperMoha86
@SuperMoha86 Год назад
Thank you Haseeb for the great explanation as usual, how can i get the soldering iron tool like yours in this video? and also how can i get the schematic diagram for any smps?
@HaseebElectronics
@HaseebElectronics Год назад
best regards it is WELLER WR3M made in Germany, you can purchase it online
@HaseebElectronics
@HaseebElectronics Год назад
drive.google.com/file/d/1_gw2TujAWDSzaWYBIpBEOreGime8hKCv/view?usp=share_link
@HaseebElectronics
@HaseebElectronics Год назад
drive.google.com/drive/folders/1TlHNmTDtY2NvDAg1XQUkMQFXhpG3aLuV?usp=share_link
@aliemlek
@aliemlek Год назад
👍👍👌👌
@nayanjagirdar8408
@nayanjagirdar8408 Год назад
👌👌👌👍
@HaseebElectronics
@HaseebElectronics Год назад
best regards
@czirkosl
@czirkosl Год назад
Very simple, make a shorcut VR trimmer and you get 13-14 V output, so 1 K trimmer is broken.
@AliRezaJoodi
@AliRezaJoodi Год назад
Do we use of a IC socket for the TL494 ?
Далее
{786} TOP221-227 SMPS IC Circuit Explained and Testing
18:21
24 Volt 480W SMPS Power Supply Repair - Step By Step
10:46
No Output In Securus 12V 3A Adapter | In Hindi
9:19
Просмотров 2,5 тыс.
{824} SMPS Output Is High, Fluctuating and Noise
12:49
{749} SMPS Is Not Working || SMPS Not Turning ON
14:10
Просмотров 120 тыс.
{1071} SMPS low output, fluctuating, Tik tik sound
11:54
{975} How to check, SMPS PWM IC switching or not?
25:23
XIAOMI для настоящих МУЖИКОВ!
0:34
Просмотров 157 тыс.
Урна с айфонами!
0:30
Просмотров 7 млн