Your IGBT series is the best I've found online. So, to better document the present state of my understanding of the following inverter controller needs so for example to use a Prius inverter (possibly converter as well for more versatility as a generator) to create a inverter-converter generator, welder and plasma cutter module: 1. For frequency control (e.g. 10Hz to 400Hz) a. For AC or DCEN & DCEP Waveform - Controlled by H-Bridge Switching Between Positive and Negative b. For DCEN or DCEP Waveform - Controlled by H=Bridge Switching Between Zero (or lower Min value) and Max Value 2. For Waveform Control - Controlled by H-Bridge PWM to create Sine Pulse Width Modulation, Saw Tooth Pulse Width Modulation, etc. 3. For Power Control - Controlled by above Waveform control with from what I see needs for the frequency range high frequency transformer designed (optimal core chosen and wound) where one transformer will be required for the DC output and another required for the AC or DCEN & DCEP output. The High Frequency Transformers seem to need to be wound on a core selected for a mid point of the power range frequencies planned to be output from the H-bridge and of course designed to handle max current (with additional buffer current rating). DC output will be rectified after the winding and another winding can be used for the un-rectified output, unless there is switching (transistors/relays) and one hf transformer can be used. Seems since higher current post the HF transformer, the switching will be more costly and might be more cost effective to have another winding and switch the lower current input going into the two hf transformers. I really need to look at an inverter design that uses the offset-balance AC circuit, since I'm guessing the above based on my present understanding. Any of the above would be just great to see. Sad how much gets wasted in the United States in regards to these inverter-converter modules as well as the CVT's being they last so long and can be found for relatively cost effective investment compared to a similar device that really doesn't exist on the market that I know of. Kind Regards, In Christ
Thank you for this video. is there any way to connect a temperature sensor to this small device instead of these button? If yes how?I want to install this for increase and decrease speed for car radiator fan. Thank you again..
Bu cihazla bir çok test yapacağın için çok işine yarayacak. Videolarında çok göreceğiz. Hayırlı uğurlu olsun. İnşallah daha çok kişiye ülkende ve uluslararası olarak yeterli kitleye ulaşırsın. Türkiye den kucak dolusu sevgiler ve selamlar. Seviliyorsun.
yes brother, it is really a very useful tool. i will try my best t share different tutorials to troubleshoot smps circuits moreover i will plan to make different project to get ideas
I have one but I don´t understand why are the negative Voltage connection because If I neglect that output and connect the negative osciloscope terminal on the ground, also works because on the ground have the return of that PWM signal.
Please can you help me. How can I drive a car ignition coil with a high power PWM driver ZK-PP2k. Similar to yours PWM but with a mosfet inside. The supplier says it handles 8 Ampere. The unit function ok with the Frequency and PWM 0-100%.
Will the set frequency and duty cycle for both channels individually remain the same even after the power supply is removed? or it gets reset once the power supply is removed.
Sir nowadays you have left replying back, Sir is there any pwm module with that we can make air conditioner compressor tester, by using that module and more components like igbt etc Please tell about module
no dear brother, i try to reply everyone, but some more busy days, i culdn't reply , i am sorry for that XY-LPWM model is 3 phase generator 0 to 150KHz. it is very useful
sir you said now you bought it from pakistani website then, are you currently living in pakistan? Because as far as I have heard from the media, the situation in Pakistan is dire now, is it true?
yes brother, i was in Pakistan. i came bake just few days before from Pakistan, and my family is in Pakistan. the situations in the news are 98% fake. unluckily in the media, there is Huge Propaganda, ground reality is not as in news. due to last floods, there is deficiency of food related goods. but it is seasonal and some areas where all crops destroyed, homes demolished. roads and other infrastructure also destroyed it will take time to regain back to normal.
RU-vid Closed Captions are extremely misleading. They edit grammar and 'add words' that were never in the official narrative (Banggood). I find this very manipulative.
absolutely perfect. sometimes the captions are misleading but it becomes somewhat beneficial for those people, who can't understand my broken English as well. so always they ask to add translation. so that they can get the closest idea about the subject by getting main content by watching video and reading captions. so they can understand it
