96-2000 Civic ignition coil test & replacement

Подписаться 1,1 тыс.

Просмотров 26 тыс.

50% 1

In this video I show how to test and replace an ignition coil. l also go over how I approached the crank no start issue that was the result. On top of the ignition coil. I also replace the distributor o ring as well as a heating hose from the engine block to the heater core.
Like and subscribe!!
Amazon affiliate links
This post includes affiliate links for which I may make a small commission at no extra cost to you should you make a purchase.
96-2000 Civic DIY(Garden hose method) coolant flush
• 96-2000 Civic DIY(Gard...
Ignition coil
amzn.to/4bIbWhz
Coolant hose set
amzn.to/4bzGbHz
Distributor O ring
amzn.to/3zCDN5J
Degreaser
amzn.to/4bSDTDP
Socket set
amzn.to/3Y2yvux
Latex gloves
amzn.to/4cyXppW
Channel lock pliers
amzn.to/460vbSu
Metric wrench set
amzn.to/460KfiP
Fluid catch pan
amzn.to/3XWrU4L
Multimeter
amzn.to/3Lf4L5Q

Опубликовано:

12 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 73

@Steve.Garrison 2 месяца назад

I'm thinking my coil is bad on my 2000 civic ex. Crank - no start. Got her towed home and fuel pump relay clicks when key is turned, and fuel pump runs. Very weak spark from right end cylinder - will have to check properly again using a spark plug on all 4 plug wires. I had just gotten it rolling smooth again with new front wheel bearings, and new radiator last summer - now this. I'll tell you what, when it rains it pours! Thanks for making this video, it helps a lot!

@HomeownerDIY 2 месяца назад

Thanks for your comment, if you have a weak spark it sounds like the coil as it changes battery voltage to 50,000 volts for the spark to occur. If you have any questions, please dont hesitate to ask!

@levicallis459 Год назад

You’re not alone on the wire harness , I’m having the same issue. In my 17 years of doing DIY mechanic work , I’ve never not been able to get a connector off

@HomeownerDIY Год назад

Thanks for your comment, I dont remember having a problem with other wiring harnesses. I bet this harness has never been taken apart, I bought the car in 2008 at 54K miles/86K KM. We have alot of moisture here so Im sure that was a factor as well. The important thing is I found a solution and got the job done.

@levicallis459 Год назад

@@HomeownerDIY yeah I hope it’s just time on mine and not a screwed up wire . Gonna do my coil tonight , so I guess we’ll see

@tjmartin5223 3 месяца назад

You have to take it off the mounting bracket then the harness will disconnect

@alexg-m6e 2 месяца назад

The reason you weren't able to disconnect the connector is because you first need to remove the connector from the metal bracket on the distributor (just push the plastic clip on the right side and pull the connector from the bracket). Once the connector is no longer on the bracket you should be able to disconnect it very easily. I struggled for 30 minutes before I found that out.

@robertbuck7186 3 месяца назад

I am so glad you showed the you can change the coil out without having to undo the troublesome connector ...were on the same page with not breaking that darn connector.. in attempting to take it apart to service the outer and inner seals on the distributor and replace the heater core hose... I found my connector frozen to the mounting bracket and stuck together as well.. The heater core hose was leaking due to motor oil dripping on it and wearing out the rubber hose from the leaky distributor o ring seal (S)... I could not dismantle the distributor and rebuild it on the bench nor buy a new one and replace it... So I only replaced the outer seal...now I am wondering why the heck did honda put a coolant outlet underneath the distributor where it could possibly leak oil as well as spring a leak in the coolant hose and cause terrible humidity and even coolant spring a leak around where the distributor and wires are... I do not know....but all in all these are great cars you can get a whole lot of miles out of them if you take care of them....

@HomeownerDIY 3 месяца назад

Happy my video helped you!!

@spencersgarage Год назад

In order to disconnect the distributor wiring harness plug you have to first take the plug off of the metal holder its on, then the plug will easily separate.

@HomeownerDIY Год назад

Thanks for your comment, I did remove it form the holder. I did everything I could think of to get it out. I am sure that youre better than me with cars, but at the end of the day, I still managed to get the job done without breaking anything.

@exclusiveshipping6333 Год назад

@@HomeownerDIY I think you did well, even the small phillips screws on the coil stripped and you managed to find a solution to that problem. Good work and great video!

@fireinthehole72 Год назад

@@HomeownerDIY how did you say you were able to get the screws you stripped off? I was working on mine yesterday and I stripped one screw so while I wait for the ignition coil I ordered to come in, I have to figure out how to get the one screw out.

@HomeownerDIY Год назад

@@fireinthehole72 Thanks for your question, this video will show how I did it, if you need more help, please come back and ask. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-VQVPRMBQfjU.html

@fireinthehole72 Год назад

@@HomeownerDIY Thanks bro. You just made my day easier cuz I’m over here wondering how the hell am I going to get that screw off. Thanks 🙏🏼

@shorelined1 Год назад

Were you pushing tab or clip down on connector. Its just plastic. A wiggle or rocking motion can help it slide apart...and pulling the lower section down. Why take dist off? Why not test the icm and coil in place?

@HomeownerDIY Год назад

Thanks for your question, taking it off would of being easier for me to clean up the distributor. I have taken hundreds of plugs apart, I have also broken plugs getting too aggressive taking them apart. With an extra set of hands could of probably gotten it apart but I found a safe alternative. Not everything goes according to plan.

@renzcaparas8484 Год назад

What's the cause if the ignition coil is broke?

@HomeownerDIY Год назад

Thanks for your question,l believe youre asking what would cause the ignition coil to fail? Wear and tear. Everything will eventually wear out. Tires, pumps, pipes/tubing will leak at some point. One of the original parts on the car(that l know of) is the alternator.

@luev2238 2 месяца назад

I have a 1997 Honda civic and it drive and very thing but I doesn’t go past 3.5 rpms it starts acting weird and I gotta wait into it goes to a new gear

@HomeownerDIY 2 месяца назад

Thanks for your comment, are you asking why this is happening?

@luev2238 2 месяца назад

@@HomeownerDIY yes , I think it would be the distributor cap and rotor but not sure

@HomeownerDIY 2 месяца назад

Its not the distributor cap/rotor. The distributor is run off the cam shaft. Its more than likely an electrical problem,either the ECU or one of the sensors is giving the wrong info to the ECU.

@sinnieleeonUtube 6 месяцев назад

Did you have to adjust the ignition timing to get it to run without any misfiring?

@HomeownerDIY 6 месяцев назад

Thanks for your question, no timing adjustments is required. If you miss wire the leads to the distributor, you will run into problems tho. Take a pic if you need to.

@sinnieleeonUtube 6 месяцев назад

@@HomeownerDIY I saw a few other videos and they said you need to adjust the timing? What if the timing is off ?

@HomeownerDIY 6 месяцев назад

@@sinnieleeonUtube lf the timing is off, you have another issue besides your ignition coil. The coil only changes battery voltage to voltage needed to jump the gap of the spark plug. I take it you have a misfiring issue? Are you getting spark to the cylinders?

@sinnieleeonUtube 6 месяцев назад

@@HomeownerDIY I got sputtering and misfiring and now it won't start BUT it cranks. I also saw oil leaks. So I will replace the entire distributor with cap and rotor when I get it. Then from watching the distributor replacement videos, they all adjust the timing with the timing lights. BUT I didn't see you do it that's why I asked. Is it because you put back the same distributor and with marking in place, the timing was not effected.

@HomeownerDIY 6 месяцев назад

@@sinnieleeonUtube What changed that its now sputtering/misfiring? What is the reason to change the distributor instead of just the cap+rotor?

@z3r0z49 5 месяцев назад

What is the black connector that is right next to coolant hose you replaced? @15:00

@HomeownerDIY 5 месяцев назад

Thanks for your question, l need you to be more specific. Is it electrical or cooling? To the right of the hose or the left?

@z3r0z49 5 месяцев назад

@@HomeownerDIY it is to the right of the hose

@z3r0z49 5 месяцев назад

It’s right underneath the distributor

@z3r0z49 5 месяцев назад

I broke it 🤦‍♂️ so I need to know what it’s use is

@HomeownerDIY 5 месяцев назад

I will let you know, please give me about a day.

@gemeinschaftsgeful 11 месяцев назад

The crack on the rotor was alarming.

@HomeownerDIY 11 месяцев назад

It's quite common since its only plastic.

@Emperor_1971 8 месяцев назад

You know if 99 n 2000 is same on the distubator ? My don’t start I check spark n fuels n relay , compression test n timing swap out the distubator from a 99 but still no start so not sure if 99 n 2000 is same I heard some say 2000 has tdc sensors in the distributor n crank pulley .my other move next is change out the crank pulley but my question is if 99 is same as 00 tho same car n motor

@HomeownerDIY 8 месяцев назад

Thanks for your question, all the parts between 96-2000 are 6th generation, so for those 4 years they are all the same. So it turns over but doesnt start?

@Emperor_1971 8 месяцев назад

@@HomeownerDIY yes sound like it’s gonna start but doesn’t if you say it’s the same then mark the distributor off now looking toward the crank sensor ?

@HomeownerDIY 8 месяцев назад

@@Emperor_1971 Lets start from the beginning, have you checked: Fuel? Air? Spark? If yes, how have you confirmed these items?

@Emperor_1971 8 месяцев назад

@@HomeownerDIY yes check all those already beside air how do u check that it was working just one day try to start n never start again , I have spark n fuel also timing mark correct and compression good , fuses n relay good new plugs n wires too check fuel pump n injector working also im gonna try swap out a ecu tomorrow just to see as well no engine check

@HomeownerDIY 8 месяцев назад

@@Emperor_1971 Fuel: You have confirmed fuel is getting to *each* cylinder? Air:Open the box for the filter. Assuming its clean, you can pump the gas pedal when you start the car. The gas pedal is actually an air pedal. The cable goes to the throttlebody. Spark: You have confirmed *each* cylinder is getting a spark? It sounds like you have rebuilt a part of the engine. Why would you swap the ECU? Sounds like your just trying to change parts to fix the problem.