9G-Tronic transmission service - 9 speed automatic transmission - Mercedes - Nissan - Aston - W222

Подписаться 2,6 тыс.

Просмотров 30 тыс.

50% 1

If you need a service manual for your vehicle, use alldatadiy. I have been using it for years and its great. Here is a link with a coupon in the USA www.pjatr.com/t/3-268932-3242...
9G Tronic transmission service - 9 speed automatic transmission oil change
s550 transmission oil change
www.fcpeuro.com/products/merc...
Josecitomarin
Jose
s550 transmission oil change
transmission service
mercedes transmission service
transmission
FCP Euro Parts and tools needed for this application :
www.fcpeuro.com/
10 qts oil www.fcpeuro.com/products/merc...
10 new pan bolts www.fcpeuro.com/products/merc...
1 New torque converter bolt www.fcpeuro.com/products/merc...
New tray may be different depending on the model. Dobble check on model and ask vendor www.fcpeuro.com/products/merc...
Fill adaptor www.fcpeuro.com/products/merc...
Guide tube www.fcpeuro.com/products/merc...
Overflow pipe www.fcpeuro.com/products/merc...
Pump tank www.fcpeuro.com/products/atf-...
JB Tools parts:
www.jbtools.com/
CTA filling system and and service key www.jbtools.com/cta-tools-340...
Scanner
E10 for pan bolts
8 mm allen key for pan drain plug (if you don't use the service key)
4 mm allen key for torque converter plug
8mm socket for bottom cover plate
18mm socket for transmission mount bolts (IF NEEDED TO BE REMOVED)
Jack stands/ wood blocks
Floor jacks
Portable lift if possible
Tray position setting points:
Position one = add oil
Position 2 = take oil out a little at the time
Position 3 = adjust oil level
Position 4 = drain oil out
Keep in mind that some fluid will remain in the pan after you drain it.
Fill up transmission temperature at 39C
Pan bolts 4 Nm = 35 in/lbs
Tighten bolts to torque spec, then go 90 degrees or a quarter turn more
Torque converter 10 Nm = 89 in/lbs
Rear engine mount 30 Nm = 22 ft/lbs
List of cars with 9G Tronic:
Mercedes C-Class
2015 - 2021 Mercedes-Benz W205 (all models)
2022 - 2023 Mercedes-Benz W206
Mercedes E-Class
2014 - 2016 Mercedes-Benz W212 (E 350 BlueTec Diesel Technology only)
2016 - 2023 Mercedes-Benz W213 (all models)
Mercedes S-Class
2017 - 2021 Mercedes-Benz W222 (all except V12 models)
2021 - 2023 Mercedes-Benz W223
Mercedes V-Class
2020 - V-Class (W447) (longitudinal engines)
Mercedes GLC-Class
2015 - 2023 GLC
Mercedes-Benz GLE-Class
2016 - 2019 GLE (W166) (except 63 AMG & 350 models)
2020 - GLE (W167) (except 63 models)
Mercedes-Benz GLS-Class
2017 - 2019 GLS (X166) (all except AMG)
2020 - GLS (X167)
Mercedes-Benz SLK-Class
2015 - 2020 SLC (R172) (except 55 AMG)
Mercedes-AMG models
Mercedes-AMG SL
2022 - AMG SL (R232)
Non Mercedes-Benz Models by JATCO as the JR913E
Nissan
2016 - 2020 Titan
2018 - 2020 Frontier
2018 Fuga
2018 Skyline
2023 - Nissan Z
Infiniti
legitstreetcars
Aston Martin
2021 - Aston Martin DBX V8 and Straight-Six
2022 - Aston Martin DBX707
Transmission service 9G Tronic
Transmission service 9 speed transmission
Mercedes S550 transmission service
Mercedes Benz 9 speed transmission
Nissan transmission
Nissan 9 speed transmission
Aston Martin transmission
Aston Martin 9 speed transmission
9G-Tronic 725.0 Automatic Transmission Service
9G-Tronic oil change
9G-Tronic fluid level check
9G-Tronic oil level
9 Speed Transmission
9 Speed Mercedes
9G Tronic 725.0 Automatic Transmission Service
9G Tronic oil change
9G Tronic fluid level check
9G Tronic oil level
S550 transmission fluid change
S550 transmission oil change
S550 transmission fluid level check
S550 transmission oil level
725 fluid change
725 oil change
725 fluid level
725 oil level
Fix it your self
Legit fix at home
#mercedes
#mercedesbenz
#9gtronic
#transmission
#astonmartin
#repairjose
2017 Mercedes s class
Mercedes S class
m157
s klasse

Авто/Мото

Опубликовано:

25 янв 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 125

@Ashoud_Anobetah Год назад

Thank you so much for making this this video. Very detailed and great video coverage! Much appreciated, as making a video makes the whole job much longer..thank you! 😊

@josecitomarin Год назад

Thank you so much for your comment. I am working on another video as I’m writing this. Make sure you see all my videos.

@georgeanddaddecker7563 Год назад

Nice job. You have a talent for these videos and teaching these services.

@josecitomarin Год назад

Thank you so much for your comment.

@paulbernal7433 Год назад

I really like your videos. Keep them coming!

@josecitomarin 8 месяцев назад

Thank you so much for your comment. I definitely will.

@Scolaweiler 5 месяцев назад

Great video Jose. Thanks for the time put into providing such a thorough explanation. Concerning the torque converter, if the fluid is draining too slowly, starting and immediately stopping the engine will cause the fluid to come gushing out. You will have to line up the opening again to replace the drain plug.

@josecitomarin 5 месяцев назад

Thank you so much for your comment. And thank you for the tip!

@ulflei 7 месяцев назад

If you do a regular change of the transmission oil there is no reason to change the oil out of torque converter.or even do a flush. Actually MB recommend not to do it for a couple of reasons ,also by $ 40 a Quart it is saving you money Great Video I just did it on my 2017 GLS the 2 rear screws are a little different to reach but also blocked by a big bracket MB don't makes it easy to work on their cars

@josecitomarin 7 месяцев назад

Thank you so much for your comment. I really don’t feel comfortable leaving the oil in the converter. You do this oils change every 60k so why not go a little further and changing what is in the converter. German engineering is very complex but it’s also the best when it comes to cars. So yeah they don’t really make it easy for anything. I’m glad my video was helpful.

@doripoo7 Год назад

Well done that man , he deserves a pint

@josecitomarin Год назад

Thank you

@elviss6783 8 месяцев назад

Safety first is right!! I always put a condom on when I work on my cars 😂

@josecitomarin 8 месяцев назад

Thank you so much for watching my videos and for your comment.

@nortsai936 Год назад

Video is much better than MB Workshop Information System steps .

@josecitomarin Год назад

Thank you so much I hope many people can take advance if it

@uhrawruh Год назад

Amazing and very educational video

@josecitomarin Год назад

Glad you think so!

@tharithchum6707 3 месяца назад

Really appreciate that sir !

@josecitomarin 3 месяца назад

You are welcome

@nathaliamurillo5609 Год назад

What a great video!

@josecitomarin Год назад

Thank you so much

@miragef191 4 месяца назад

Great job!!cheers.

@josecitomarin 4 месяца назад

Thank you so much

@bwebb671 Год назад

Very informative video

@josecitomarin Год назад

Thank you for your comment

@darrenjefferson6492 Год назад

You made my day! use a service such as S M Zeus!!

@josecitomarin Год назад

Thank you

@S203 23 дня назад

I can only speak to the Nissan Titan, but I believe they only got the 9-Speed Jatco from 2020-2024. Prior to that, there was a 7-speed Aisin transmission, not sure if the maintenance procedure would be the same.

@josecitomarin 22 дня назад

Thank you so much for your comment. Jatco is actually licensed for production of the Mercedes 9G-Tronic transmission for some of their Nissan and Infinity vehicles

@ronpi1293 Год назад

fantastic!!!

@josecitomarin Год назад

Glad you like it!

@clintprice2123 7 месяцев назад

I’m surprised Mercedes didn’t and you also didn’t drill a hole to get that odd bolt out from above the trans mount.

@josecitomarin 7 месяцев назад

Thank you so much for your comment. It would have been easier if they designed it with that in mind. But I wouldn’t be the one to change their engineering. Maybe a little hole won’t change much, but I rather not.

@atrzebunianiebies Год назад

Great video! Just to confirm, you don’t need to cycle through the gears after filling and waiting for temp to reach 39 degrees, correct? Also, on a 9g tronic MCT (AMG only) w/o torque converter, does the 9 liters drain from just the pan or somewhere else after draining from the pan? Does anyone know?

@josecitomarin Год назад

Thank you Artur for your comment. There is no need for cycle. I took 9 liters out and I put a little over 9 liters back, so I am very comfortable with it. I do not think it makes a difference to cycle through gears. I don’t like the idea of running it dry even though it would only be for a fraction of time and not completely dry. Another reason I am comfortable with it is that I change the oil before time and not after. With the MTC. I have not done one my self, but the way I have seen it done is that (and it might sound silly) you drain the oil from the pan and from the cooler hoses two times. On the first change the oil that is left will mix with the new oil and when you do the second oil change you will have much better, cleaner oil in the trans. Now, with this procedure, you run the engine after you have changed the first time (wet trans), go through gears so you can get all of the oil moving throughout the entire system, get up to operating temperature, let it run for a few minutes and then flush again. If you do it your self it doesn’t cost you much. And since you do not do this service all the time is not too much of a pain. The car is already up and ready. I would also have the car warmed up before I do even the first change. Bring the car up to operating temperature, and let it cool off for a few minutes. Wear gloves so you don’t burn yourself.

@benz961 Год назад

Excellent detailed video. I've recently had 9g oil and pan changed at Automatic transmission rebuild specialist, refill was 5 and half litres they didn't drain torque converter. Should I be concerned?

@josecitomarin Год назад

Thank you for your comment. I would say your oil is half way clean. It’s not terrible but it would’ve been good to do the entire thing. I hope the old oil wasn’t too bad.

@talonnied1 Год назад

Thanks!

@josecitomarin Год назад

No problem

@tharithchum6707 3 месяца назад

Hi Jose, thank you. Would you post the link of the scanner you got from Amazon, if you don’t mind?

@josecitomarin 3 месяца назад

Of course here you go. I just saw it and price went up. But it’s still cheap. $31. When I bought it it was $19 then it went up to $25. I use it in a few of my videos a.co/d/e2kO3PG

@tharithchum6707 3 месяца назад

I don't have a scanner to measure the temperature to measure the fluid level, does anyone know the way to check the temperature without having the scanner on 9 speed automatic transmission? On my old mercedes 2014 ML350 the ATF oil pan is metal and it doesn't require to change the whole pan but only the gasket when it comes to ATF service...I usually check the temp through my laser temperature tool by pointing it to the ATF pan while the engine is running. It reads the temp without having to use the scanner, but since the 9 speed comes with plastic ATF pan my laser tool probably won't read the temp correctly through the plastic pan, though I have not tried it yet, if anyone have an idea about this please help answer my question. I appreciate in advance for your time

@josecitomarin 3 месяца назад

Thank you so much for sharing. You can simply get the small scanner from Amazon for $25 and you connect it to your phone. If not your laser tool will work. Just go up a little higher in the transmission to the metal. In my video I showed how the $25 scanner works perfectly

@TerenceThorley Год назад

I thought the rest of the oil was in the transmission oil cooler that has a feed via the two pipes that come from the transmission housing, to drain this you have to run the engine to operate the oil pump with the return pipe disconnected and add and drain a litre at a time? ( 4.5 litre in the transmission and 4.5 litre in the oil radiator ) You say you got 4.5 litre out of the torque convertor, was this also coming from the transmission oil cooler?

@josecitomarin Год назад

Hi. Thank you so much for watching my video and commenting on it. The amount of oil that is held in the radiator is very little. It doesn’t make a difference. There are people that don’t even drain the torque converter. I got 9 liters out and I put just a little more then 9 in. And that is what the 9g-Tronic trans (with all its components) on this car calls for. As you mentioned, some of the oil from the lines may already come out from the torque converter, but what is being held is not a significant amount to make a difference on the operation of the transmission or the lifespan of it. So I am not really worried about it.

@talonnied1 Год назад

Jose, excellent vid! What’s the size of those wooden blocks? Thanks.

@josecitomarin Год назад

Thank you so much for your comment. They are 6x10x20

@dino69xsx Год назад

Great thorough step by step video Thank you I have a glc 220d 4 Matic , when do u recommend to change the transmission oil Your suggestion would be appreciated Have you heard about Liqui Moly brand ?

@josecitomarin Год назад

Thank you so much for your comment. You have to do it every 60k as well. Liqui Moly is great. I use a lot of their products. Take a look at my other videos as well you’ll see the products I use.

@dino69xsx Год назад

Thank you Jose Just changed oil with Liqui Moly top tec4200 n added Ceratec Engine much quieter and responsive too Thank u 🙏🏻

@josecitomarin Год назад

@@dino69xsx that is great. Thank you so much for your comment

@laythalsaud8810 15 дней назад

Hi Jose. I have a 2017 C300 convertible equipped with 9g tronic transmission. They told me that I just need 5 liters of transmission fluid since the pan will drop 4 liters and the torque converter drops only 500 ml, is that correct?

@josecitomarin 15 дней назад

Thank you so much for your comment. As far as I know you need about 10 liters for a trans service. Even the 7g tronic needs about 10 liters

@julianlandeau 9 месяцев назад

hi am i right in hearing that 9litres of oil are needed to do this? i heard about people doing a flush. i.e dropping everything out the pan about 4 litres doing a flush then doing again with new pan and oil about 4.5 litres. your method has 9litres in one go by draining the the torque converter direct. which seems better tbf as is all the oil in one go rather than leaving half in and being contaminated. im currently on 61k mikes and 7years on a s213 model.

@josecitomarin 9 месяцев назад

Thank you so much for your comment. You definitely drain from the torque converter. That way you take it all out.

@julianlandeau 9 месяцев назад

@josecitomarin that's what I thought, thank you for your reply. I can't believe some people are changing half the oil and calling it an oil change. the pan and half the oil is like 90% of the cost anyway. Good to see it done properly 👍

@josecitomarin 9 месяцев назад

@@julianlandeau right. It’s not even difficult to get the fluid out of the converter. Just needs patience

@josetorrado7951 Год назад

Jose, greetings from Portugal. Made a great video very detailed. Can you tell me which OBD diagnostic tool you use and also the one for the mobile phone? Thanks.

@josecitomarin Год назад

Hello Jose from Portugal. Thank you so much for your comment. The ones I used are iCarsoft CR Ultra and the one for the phone is the Kobra OBD2. I know the iCarsoft one is available in Europe. Not sure about the Kobra. But they have more in Europe. iCarsoft also has others that are just for a particular car, check out their website. No fees for upgrades. Make sure to take a look at this short I made on those scanners. Also, if you didn’t already please subscribe, like and watch more of my videos. ru-vid.comyc8Ejc9TRlw?feature=share

@josetorrado7951 Год назад

Thank you so much!@@josecitomarin

@josecitomarin Год назад

@@josetorrado7951 no problem

@florindorgo8843 3 месяца назад

All perfect till close to the end when you're covering the video and can't see anything

@josecitomarin 3 месяца назад

Thank you so much for your comment. What part are you referring to? Is there anything that you would like me to clarify?

@dino69xsx Год назад

Hi Jose Can u change the oil without the pan change ! What’s ur view? Run it for another 20miles and change the whole filter kit

@josecitomarin Год назад

I would just change the whole thing. It doesn’t really makes sense to do that. Just change it all and wait another 60k to do it again. I’m doing it every 50k

@dino69xsx Год назад

Thanks. Sounds good 👍

@josecitomarin Год назад

@@dino69xsx no problem

@Rmayrap Год назад

Great video Jose. Did you change the filters? I didn't see that step. I have the 2015 S550 with the 7G transmission. Would the procedure be similar to yours?

@josecitomarin Год назад

It’s very similar. I got the part at FCP Euro. They will help you find the correct parts for your car. Give them a call

@Rmayrap Год назад

@@josecitomarin will do, did you change the transmission filters?

@josecitomarin Год назад

The filters and seal come in the tray already installed. Some cars come with the filter and seal already installed and asome separate

@atrzebunianiebies Год назад

Thanks Jose for the detailed explanation! I appreciate it.

@josecitomarin Год назад

@@atrzebunianiebies any time

@TheFrenchPug 5 месяцев назад

When you go back under after measuring temp, what initial position do you out the tool into, position 1? Then, turn to position 3 and let it drain, then back to 1? Thanks!

@josecitomarin 5 месяцев назад

Thank you so much for your comment. Yes, you start at position 1 then change to position 2 to drain slow. Then to 3 and back to position 1.

@TheFrenchPug 5 месяцев назад

@josecitomarin Thank you. Got it done today. I was freaking out when it started pouring out steady, but then it stopped and dripped. Car still runs like a champ, but the fluid was pretty dirty for transmission fluid. Thanks so much again!

@josecitomarin 5 месяцев назад

@@TheFrenchPug no problem. I’m glad it worked out.

@TheFrenchPug 5 месяцев назад

@josecitomarin I used the original pan and filter because I ordered the wrong filter and gasket online based on their confirmation that our transmission was a 2018 c300 with a 729 transmission. All the videos I watched on 2018 C300 showed the pan with 6 bolts and a separate filter, reusable pan. Once I got under the car, shock and awe struck me and I panicked because I didn't have the proper tools to refill the pan and had to Amazon 1 day order them for $20. So, I spent an extra $90 for no reason. But, I got it done. And, I found the fluid for $8.39 a liter and ordered 10. So, I have 5 for next time and will just order a new pan at 100k miles.

@josecitomarin 5 месяцев назад

@@TheFrenchPug just don’t wait too long to do the next change. Who knows how that filter was

@narcissistinjurygiver2932 Год назад

what position do you set it at to set the fluid level?

@josecitomarin Год назад

You set it in position 3

@lownology Год назад

Great content! What is the tools you use to read of oil temp to 39 degrees?

@josecitomarin Год назад

That is an OBD2 scanner. You can get a $20 scanner from Amazon or you can get a better one that is bidirectional from specialized companies. I used both on the video. The bigger one is from Icarsoft. The one from Amazon will give you codes and live data is great. The bidirectional will allow you to send commands to the car as well.

@lownology Год назад

Alright. Thanks 🙏

@josecitomarin Год назад

@@lownology you are welcome

@lownology 3 месяца назад

@@josecitomarin Hi again Jose! i´m now about to change oil on my 9g trans. If i took 6 lites out and I put a little over 6 liters back. I still have to do 39 degrees check?

@josecitomarin 3 месяца назад

@@lownologyyou should definitely look for the temperature measurement. Make sure you do the torque converter. Get the scanner you’ll need it for other things as well. Anybody who owns a car should own a scanner

@Johnmam9984 7 месяцев назад

Hi , i have 2019 E63S. Is this method also applicable to my car? Also, torque converter drain is absolutely necessary? Or can I skip? My car just hit 40k miles.

@Johnmam9984 7 месяцев назад

I just realized i have MCT without torque converter..

@josecitomarin 7 месяцев назад

Hey. Beautiful car. Right. Your transmission is slightly different. No torque converter. But it’s basically a 9gtrinic. You still have some miles before you have to service it. But it’s also a good idea to do it before

@Johnmam9984 6 месяцев назад

@@josecitomarinso if i dont have torque converter, i dont need 10L of fluid? I drained from pan and only 4L came out.

@josecitomarin 6 месяцев назад

@@Johnmam9984 no. You only need about 4L

@EdasTattoo 11 месяцев назад

Hey man, the main cap on my car is leaking oil, I have oil changed 8 months ago. Can I just replace with the new cap? Thanks

@josecitomarin 11 месяцев назад

Hi. Thank you so much for your comment. It doesn’t hurt to replace it. They are very inexpensive. Specially if you know that it’s leaking from the cap for sure. But you are going to have to refill your transmission again.

@EdasTattoo 10 месяцев назад

@@josecitomarin Hey man thanks for the reply. Why do you suggest refill again?

@josecitomarin 10 месяцев назад

@@EdasTattoo well. The cap is on the bottom of the tray. You are talking about the transmission right? Or are you talking about the engine? If it’s the engine no need to refill. And if it is the transmission, you don’t want to use the same oil after you take it out to change the cap. Who knows how much oil the car leaked by now.

@EdasTattoo 10 месяцев назад

@@josecitomarin Thanks for your reply. Im talking about transmission yes, it didn't leaked much, its just wet a bit. Once i remove the old cap, it will not start to drain as it has second cap inside for filling and draining isn't it?

@josecitomarin 10 месяцев назад

@@EdasTattoo yes . You are correct. Remove the cap. The fill tube is inside

@user-vs2xg4yv2u Год назад

At how many miles does this need to be done ? Thanks 2020 W222

@josecitomarin Год назад

Thank you so much for your comment. You have to do it every 60,000 miles

@user-vs2xg4yv2u Год назад

@@josecitomarin thanks

@josecitomarin Год назад

@@user-vs2xg4yv2u you are welcome

@lucianghe2658 6 месяцев назад

What kind of torque wrench you using?

@josecitomarin 6 месяцев назад

www.lexivon.com/collections/torque-tools

@user-he1xq5jn7e 3 месяца назад

I can't understand the reason why someone would service the 9g automatic transmission at his house. You buy a car like a mercedes, and you know that you will need money for maintenance, right? I am also a mechanic and I have the E300de, but I am taking it to the Mercedes dealership so that I have all the guarantees because I paid 110,000 euros for its acquisition. and as you know, the specific automatic transmission has enormous technology and a mistake might turn out to be fatal...!!! you are a good engineer and great video. my knowledge is to go to an official car repair shop so that we can have peace of mind... as long as you have money of course..thanks!,🙏🏼

@josecitomarin 3 месяца назад

Thank you so much for your comment. I am actually doing this as a hobby, I am not a mechanic, or I guess you could say I am, lol. I have been taking care of my cars for like 20 years. I just don’t see why you couldn’t drive a luxurious car and pay the same money for it (used of course) that you would pay for a regular car and drive in style. I really don’t see the difference in doing the trans service on a 9G transmission from a Mercedes or Nissan than on a regular Chevrolet transmission where you follow the same kind of procedure. You are right in all the electronics and craziness involved, but as long as you do it correctly and follow procedure you should be okay. So I don’t think you need to have the money to pay for the maintenance, if you can do it yourself, after all the procedures are the same as in any other vehicle. Plus, you don’t do this kind of service on a 110,000 euro Mercedes you are doing it on a 15k or 20k euro Mercedes after 60k miles when the factory warranty is done. The trans service where I live is $1400. I spent $300. Thank you so much for watching my videos. I appreciate you taking the time and writing your comment. We need to have this conversations so people could really see the pros and cons. Hope to hear more from you in this or any of my other videos. And if you have a channel, please share so we can learn what you do as well.

@lownology 3 месяца назад

@@josecitomarin agree with you 💯 👏

@josecitomarin 3 месяца назад

@@lownology thank you so much

@dimi911 6 месяцев назад

Which App did you use to read the transmission temperature?

@josecitomarin 6 месяцев назад

Thank you so much for your comment. It’s called car scanner. It’s blue with a white check engine light symbol

@dimi911 6 месяцев назад

@@josecitomarin great, thanks for your help and the great video!

@josecitomarin 6 месяцев назад

@@dimi911 thank you so much

@dimi911 6 месяцев назад

@@josecitomarin can I also ask please what type of pump do you use to fill up the gearbox? Is it a plain hydraulic type or electric?thanks

@josecitomarin 6 месяцев назад

@@dimi911 I only used a manual pump. It’s listed on the description.

@AColladoVivas 15 дней назад

Now I see why this service is so expensive 😩

@josecitomarin 15 дней назад

Thank you so much for your comment. Yes they do charge a lot, it needs some work, a lot of oil, new pan, new filter, etc

@bobmcgehee1749 11 месяцев назад

Another reason mechanics hate engineers.

@josecitomarin 6 месяцев назад

It takes a little longer than a regular car. But is not that bad.

@bobmcgehee1749 6 месяцев назад

Maybe, but it’s unnecessarily complicated and you have to buy the stupid tool.

@josecitomarin 6 месяцев назад

@@bobmcgehee1749 it’s still a lot cheaper then having it done by somebody else. And then you have to make sure they do it right, which is the most important part.