A CHROMEBOOK for 3D Printing? TinkerCAD & Kiri:Moto Tutorial!

Подписаться 46 тыс.

Просмотров 25 тыс.

50% 1

Folks have often asked, "What is the cheapest computer I can use for 3D Printing?", so I set out to answer that question for the 3D Printing Community! This Samsung $70 Chromebook is by no means a powerful Computer, but can it be used to run a 3D printer and even 3D design custom parts? We will use AutoDesk TinkerCAD and Kiri:Moto for our 3D Design software and Slicing Software. No Linux rooting or dev menus in this tutorial!
AutoDesk TinkerCad: www.tinkercad.com/
Kiri:Moto Web based Slicer: grid.space/kiri/
Stained Glass by: / seaofdoom
TimeStamps:
0:00 - Intro
0:58 - $70 ChromeBook?!
1:56 - What are we designing?
2:23 - Equipment Recommendations
2:40 - TinkerCad Basics
3:46 - Designing in TinkerCad
9:31 - Kiri:Moto Intro
9:53 - Using Kiri:Moto
14:25 - G-Code to the SD Card
15:05 - TO THE PRINTER!
15:39 - Hanging the Stained Glass!
16:05 - Conclusion
16:24 - Outro
Gameplay at start from: "The Outer Worlds" by Obsidian Studios
-----------------------------------------------------------------------------------------------
Please consider supporting by checking out my various links:
www.mandicreally.com/links
-----------------------------------------------------------------------------------------------
Affiliate Links:
*** Polymaker Filament: us.polymaker.com?aff=28
*** E3D Products: e3d-online.com/?aff=23
*** Starter 3D Printer: amzn.to/3QCwbU9
*** Large 3D Printer: amzn.to/3ThBZEH
-----------------------------------------------------------------------------------------------
Filmed with:
*** Main Camera: amzn.to/3c6ULgV
*** Main Lens: amzn.to/3c616cp
*** Overhead Camera: amzn.to/2U4b1nZ
*** Video Recorder Used: amzn.to/3ymN90U
*** Action Camera: amzn.to/2ATHS73
*** Second Camera: amzn.to/371EhBM
*** B-Roll Lens: amzn.to/2xmg85L
*** Wide Angle Lens: amzn.to/2YiZTmH
*** Slider: amzn.to/3nGZ1Uh
*** Lav Mic: amzn.to/2DFwgR5
*** Shotgun Mic: amzn.to/2IjTJiB
*** Mini Tripod: amzn.to/2Eok8Fw
*** Monopod - amzn.to/2C1YEMU
*** Tripod: amzn.to/2yASruf
*** Gimbal: amzn.to/2FNwesV
*** Primary Lighting: amzn.to/2jHROnW
*** Additional Lighting: amzn.to/2DImspx
*** RGB Lights: amzn.to/2UUGAOk
*** Drone: amzn.to/2yDkwkI
-----------------------------------------------------------------------------------------------
The opinions expressed in this video are my own, from my personal experience. This is not a paid product advertisement. Please feel free to let me know what you think of this tool, or suggest alternatives I should check out. Disclaimer: This is not a paid advertisement. This video is solely my opinions from the use of these products and based on the specifications of them. Some of the links provided are AMAZON AFFILIATE LINKS or others. Affiliate links give the MandicReally a small advertising fee for every purchase made via those links. This does not cost you anything more than if you purchased them normally.

Наука

Опубликовано:

11 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 131

@smooth-juice10101 Год назад

As a complete Newby and I mean complete Newby this video has helped me so much. I have just completed my first 3-D design after wanting to do this for years and thinking I needed a proper PC. Thank you doing this video and you are a complete a legend.

@pro-editor623 26 дней назад

pls help my machine isnt up there it is sovol svo1

@dawnforrespect7758 2 месяца назад

Lawd have mercy! After 3 days of stressing, googling everything imaginable and even rewording the same questions... I found exactly what I needed all along. Thanks man, I supper appreciate you. Now to see if it worked lol🤯

@Mobile_Dom Год назад

you, good sir, are the realest. thanks for bringing the idea to life man

@distanceyaself8975 Год назад

You are a legend man I've been putting off getting my first printer because I thought I'd have to get a high spec computer to go with it, thanks for the video you just got a new sub... gonna go binge watch a load more of ya vids.

@clubbuild3544 Год назад

This was so helpful thank you and keep up the good work

@GridSpace Год назад

Nicely done. Thanks for highlighting Kiri:Moto

@MandicReally Год назад

Rad, thanks for making it for folks to use.

@CoranettaWoods 3 месяца назад

This video was SO!!!! Helpful Thank you!!

@jcperdomoybarra1 Год назад

Excellent video! One of the things I struggle with is to be able to slice stls in my iPad, and this tutorial do work in that use case! I would love to have prusaslicer or any fork available for the iPad… but this is a quite good workaround! I’m enjoying more and more your content, keep going!!!! Cheers from Madrid!

@deviantpodcast3938 3 месяца назад

This Hass to be the most absolutely helpful video ever seen on RU-vid. Thank you and good night.

@Ben-qh1ku Год назад

This is a great solution for the price. Thanks for the video 👍

@joeynelson9530 11 месяцев назад

Thank you for the video I'm very new to 3D printing and I had a Chromebook with very difficulty on how to make it work your video was very instructive easy-to-follow and overall thank you very much I will be watching more videos

@CherryCos 6 месяцев назад

This is the most helpful video for printing with a chromebook ever!! There are tons of tutorial videos and articles but nothing felt as clear and concise for a printing noob like myself than this video!! including free web-based programs to use is seriously the lifesaver in this, because i'm not an expert at coding at all and also some of the other programs, like Cura, have linux install options but i have found more bugs with those.. i never even knew about kiri:moto until this video and man this is all just super helpful!! for the first time in the 6 months i've had my Ender 3 i feel like i can actually use it, thank you!!!

@CherryCos 6 месяцев назад

For the record, I have an Acer Chromebook 516 GE and i'm using the Ender 3 with manufacturor parts only (so far), and so far everything is running smooth with the test print that i'm running! Kiri:Moto is just as user-friendly as shown in his tutorial, in my experience, and everything is running smooth so far!

@Noreallywhy 6 месяцев назад

Can’t thank you enough!!! My kid begged for a 3D printer despite my attempts to explain that they’re really a hobbyist device that takes investment. I didn’t do enough research to realize that their Chromebook wouldn’t be able to manage the software needed. If it weren’t for this video I’d have no idea how to help them use their Ender3. THANK YOU!!!

@tonylambert3012 6 месяцев назад

Thanks for the video!!! This answered allllll my questions. My printer should be here in a few days and only have a chrome book now. Plus I'm not that tech savvy. This helped a TON!!!

@SamJantz Год назад

A free online slicer, what a time to be alive. When I started I used slic3r and that was a real sink or swim moment. That being said, I did run it on a janky laptop that didn't even have a battery for it anymore. Where there's a will, there's a way and all that :D

@gpedrok Год назад

I have used AstroPrint for last 3 years on my refurbished Acer Chromebook R11, pretty cheap and Astroprint is working really well, will try Kiri:Moto

@falconlord7086 Год назад

Thank you so much I have been at this for so long thank you 🙏

@Rushmere3D Год назад

TinkerCAD has alignment tools in the top right and in the bottom right you can change the movement amount :).

@MandicReally Год назад

Thanks for the info! I played with it a bit but wasn't having any luck and didn't went to expend a ton of energy on this video. 😅

@RoyceMunday56 Год назад

Really useful, thanks

@jacobcooper7387 Месяц назад

You just earned a Like, Subscribe, and Comment. It’s rare that I do even one of these. I wanted to use an online slicer.

@gerardonovelo8098 Год назад

Great video! I've been using this workflow for a bit and your instructions cleared a lot of things up. Any tips for someone with zero engineering or 3D background on what to move onto after TinkerCAD can't quite cut it anymore?

@ItbeTrey3 Год назад

That’s crazy and I gotta chrome book too I just need the printer now

@joelstitch 11 месяцев назад

Thanks for the video. I havent used Gridspace in a while because it would constantly give me a print bed size error even though I set my bed size right on the settings. Will try again.

@markrainford1219 4 месяца назад

Thanks so much. I didn't even know my Chromebook had an SD card slot 😂👍

@WhiteG60 Год назад

I had OnShape working on one of my kid's school provided Chromebooks. It sucked with a 1280x768 screen, but with an external monitor it ran fine. OnShape 'pro' is also free for students. My biggest problem with TinkerCAD (which is great, I used it for quite a while) is that the workflow doesn't translate to any other design program, so once you outgrow it, you need to relearn the whole process from scratch using 2D and extrusions. It took me months to wrap my head around how that all worked after using TinkerCAD.

@MrGerhardGrobler Год назад

Good video. I use a connex windows laptop with basically the same specs. and well. It slices as fast as my 9 year old core i3 desktop PC. Yes, I am broke. I also use tinkercad to design my parts for my products. It does have limitations, but you can work around them with imagination. As I only reacently discovered your channel through 3DPN's channel and your monster kyle cup, I have been playting catchup with all the videos. Great channel you have here. Very real.

@mrmechano 11 месяцев назад

Next step Onshape. I did it and now I biuld more refined and complex items.

@speakingthetruth9013 24 дня назад

Thank You Man

@nathan22211 Год назад

you can run Prusa Slicer on a Chromebook if it supports Corsini, heck I've run IceSL on one too. Also, consider onshape as an alternative

@indecisivesquirrel3dlabs78 Год назад

The lab coat love it!!!!!!🤪🤪🤪🤪🤪🤪🤪

@user-vu3zz5wf6f 7 месяцев назад

I have been a newbie to 3-D printing for about a year now and I have not made one print, my any cubic printer that I got for Christmas just sat in my room but now I can make stuff

@BeefIngot Год назад

With things like I shape, if you aren't private with your projects you can do some really detailed things with just a chrome book.

@Best-Big-brother_on-earth 8 месяцев назад

I was just wondering with what you have on this video can you also make action figures with the Chromebook

@heidikazulak2651 2 месяца назад

trying to print on Dremel 3d 40 it is not listed in Kiri:Moto..is there a way I can add it?

@Kitjuni 9 месяцев назад

How do I find the information to enter into Kiri:Moto for a Geeetech E180? Is that info just in the user manual somewhere? I can't find any info online on what I need to enter. :(

@fishingwithcarson2376 11 месяцев назад

I need help with kira moto. I just got an ender 3 s1 pro and kira moto does not support that printer for there settings. So what I need help with are the best settings for kira moto for the ender 3 s1 pro.

@LuniDuni Год назад

I have a question about kiri So I use a Chromebook for everything and I need to do a larger project with supports, however whenever I try to use supports because of the quantity of supports it lags out and when I slice it, it barely loads then doesn’t move past that point Also thank you for showing me besides the whole support thing the software works really well

@bribri0528 Год назад

i have an adventurer 3 can i use this? New to 3d printing

@RafaelDrumondRego Год назад

Not sure if there is a place you list this, but what upgrades are you using in your print bed and heatblock?

@melbatoast1985 Год назад

i have a monoprice select mini pro and not seeing it in kiri:moto what do i do. first 3d printer and have no clue what i'm doing.

@Carside.1 6 месяцев назад

can you please make a video about kiri moto tpu settings?? i bought tpu and i dont know how o use it i hope you can help me

@premium1729 7 месяцев назад

Does the Ender Creality 3 come with a SD card?

@chriswilliams1798 6 месяцев назад

Any suggestions for a Creality K1

@SniperAngle12 8 месяцев назад

I am a year late but it seems to me that the base menu does the settings for the number of base layers you have, while output does the rest of the layers. I don't think it makes a huge difference to have different settings other than turning off the fan for the base layers though.

@ijcarroll 6 месяцев назад

Low spec 3d printing? I use a raspberry pi4b 8gb in an Argon1 v2 case to use prusa slicer and cura with tinkercad and onshape to 3d print stuff and have done so for the last year an a half.

@HumberOrtega-nw4ro Год назад

hi , can you help me on how can i add a voxelab printer to kiri moto ? Great video and thanx so much for sharing your knowledge, your awesome!

@MandicReally Год назад

Which Voxelab? Most of the Aquilas are "Ender 3 Clones" so you will be fine to just pick an Ender 3 in Kiri Moto.

@yangire44 Год назад

So I have a chrome book and do they for resin 3d printers?

@nickrodriguez1736 Год назад

It would really help if you showed us how you would make this exact same project for in fusion 360.

@MandicReally Год назад

Not a bad idea Nick. Maybe I’ll find a budget laptop and redo this video with Fusion 360. Can show the progression.

@neldareyes135 4 месяца назад

What if I have an reality K1? I don’t see it on the list

@sherrinaclark8341 Год назад

Can't find the UP! 3D printer. Suggestions?

@shaniceball9052 13 дней назад

4:48 How do you download it? Do you click "Start Tinkering"?

@kryptonicloser Год назад

I need to buy another laptop. Mine is about 6 years old was only used for 3D printing programs and downloading STLs. Buttttt now it’s having a hard time running a lot of sites even. It’s an HP with 8GB ram and 1TB hard drive. Sucks it went out so fast on me. Any idea what I should get next

@toepunch001 Год назад

Where did you get the hanger?

@user-vr2wl3sf9b 3 месяца назад

i have a mono price printer what are my options?

@ethanadams9388 Год назад

Ruffly how long does it take to slice?

@P3achesandmelberries 3 месяца назад

So I use the flash forge adventurer 5m 3-D printer, and it’s not on the list

@MaxHackbarth Год назад

Nice to know that my potato powered Chromebook will be able to print my nerf gun

@leviwright6431 11 месяцев назад

Anyone have suggestions for the Anycubic Photon M3 Plus?

@StephenSmith-vs8hr Год назад

Thanks 👍😃😃😃😃😃

@mrmechano 11 месяцев назад

Have you tried to compile a slicer from scratch enabling Linux sandbox on the Chromebook? It's the only way if the Chromebook is an ARM-based CPU.

@user-he8vs6if1i 4 месяца назад

Super new to this. It’s actually for my son we are learning it together. We have a chrome book and no one told me that UltiMaker wouldn’t work on that 😂👍🏼 We have a Elegoo Neptune 3 pro. I have input the information, but the point of origin is the bottom left corner and prints in the middle. However this program I can not find where to change the point of origin, does anyone use the same printer and have figured it out? It’s getting really frustrating

@silentraven37 Год назад

ive done a few prints so far and they turn out great. how ever the outer most layer seems incomplete, there is no outer shell so to say. fonts and small detail parts look rough and unfinished. ive played around with all the infill and shells counts but nothing seems to fix this issue

@gpedrok Год назад

Make sure you are setting the outer layer to prin first, should be a box to check, if you print inner layers of the shell first any excess material can create bulges on the outer surface, you could adjust the percent of flow but you'll never know exactly what you are going to get. This is not a good choice for overhangs.

@aymenaabi5747 Год назад

Hi you can do a video for anycubic photon mono 4k pls is dont work wit anycubic photon mono 4k

@MrSpeakerMBurns Год назад

You should use the alignment tool.

@Skookylol 2 месяца назад

I get errors everytime i try to transfer a gcode file to my sd card ive tried everything and nothing is working

@kristyeast 6 месяцев назад

i just started 3-d printing and dont know if i can use the ender 3 settings for my ender 3 v2.

@MandicReally 6 месяцев назад

You can. There is no difference as far as this slicer will be concerned.

@VicturdLovesTurtles 4 месяца назад

my ender 3 3d printer malfunctioned and now i cant keep the tf/sd card in the card slot. It worked first but i kept putting it the wrong way and the slot broke now i cant use it to print and i can't use a usb cable/port because i use a chromebook for my prints so I cant download any softwares that let me print with a usb cable

@pyroignis3305 3 месяца назад

You can get a USB that takes a SD card I'm not sure if it works that way tho

@kyndramagana 4 месяца назад

I can’t find the Tina 2 on Kiri Moto

@darrynwingfield1452 6 месяцев назад

What device should i select on kiri for a elegoo neptune 3 pro.? Please

@MandicReally 6 месяцев назад

Ender 3. The 3pro is an Ender 3 clone with direct drive so you’ll want less retraction (somewhere around 1mm most likely).

@josephjoe7836 Год назад

i have a elegoo neptune 2 3d printer and i didnt see it listed on kiri moto site what should i do

@MandicReally Год назад

Creality Ender 3. The Neptune 2 is a pretty direct Ender 3 clone.

@user-xo3oh8tk5b Год назад

I have a neptune 3 max and I am not seeing it on that slicer

@I.am.sasha.268 Год назад

hey quick question why can’t i find my neptune 2 in the slicer should i just select an ender 3

@MandicReally Год назад

Yes, just use Ender 3. The Neptune 2 is such a direct E3 clone that it won't matter for any settings in that slicer.

@1blktalon Год назад

I don’t see the AnkerMake M5. Does anyone have a suggestion for me instead of Kiri:Moto or maybe a default machine to choose. Thanks for the video. Glad I found your channel.

@MandicReally Год назад

The M5 being such a new and specialized machine, I cannot make any recommendations. I only know of 1 slicer aside from Anker's own that has a profile for the M5, and it is a github project offshoot I wouldn't point a new user toward. I'm supposedly getting an M5 sometime soon, maybe I can get a better idea then.

@1blktalon Год назад

@@MandicReally Ok. Thank you for the reply. I have so much to learn.

@isaiahwinegar9489 6 месяцев назад

What about for an flashfoege Adventure 3

@steveh6883 2 месяца назад

Anyone got any ideas how to add Nova3D Elfin as a machine to Kiri:Moto?

@fastfood122 Год назад

Yes please can u do fusion360 on a low budget as there is no videos i can find thank u

@troypostishek2557 2 месяца назад

i have a elegoo which is not listed

@I.am.sasha.268 Год назад

hey quick question do u think it would work exporting pre-made thingiverse files

@MandicReally Год назад

I don’t know if I follow. You mean downloading designs on Thingiverse? They are most often STL files. So like I said with downloading my designs off Thangs, just download them and use the Kiri:Moto slicer to slice them for printing.

@izziinkslinger1118 Год назад

I have a chromebook and anycubic mega S works fine

@VoidHeartProduction Год назад

What if we have a resin printer not a filament printer

@logdmith7388 Год назад

Does Kiri moto work with the voxelab aquila c2 3d printer?

@MandicReally Год назад

Choose the Ender 3 and you will be good. The Aquila is a clone of the Ender 3 so that's what you can pick in various slicers.

@logdmith7388 Год назад

@@MandicReally TYSM any aquila? Or specifically aquila c2

@user-ec2vp6yx9f 10 месяцев назад

I have a anycubic viper and it's not on Kiri:moto can you help

@MandicReally 10 месяцев назад

Just pick an Ender 3. The Vyper is an Ender 3 clone.

@user-zf3wl3db5u 6 месяцев назад

there is no ender 5 plus on the kiri:moto slicer

@nelsonreddington4603 Месяц назад

I have an eryone thinker se

@thememer7700 Год назад

my printer did not show on the list mine is a elegoo Neptune 2

@MandicReally Год назад

Just choose Ender 3. The Neptune 2 is an Ender 3 clone machine, it’ll work fine.

@franciscovargasmutis2226 Год назад

I got a Geeetech A10 that is not listed in KiriMoto 😞

@MandicReally Год назад

That is an Ender 3 clone, just choose Ender 3.

@Ice-vr- Год назад

So I did what the video said and I put my stl in my sd card but when I put it into my Neptune 2s it did not work

@alexthelion335 Год назад

Did you slice the stl file? The file put on the sd card should be a .gcode file

@Ice-vr- Год назад

@@alexthelion335 sorry that I saw this really late but I found out how it works thanks for the help though

@Ice-vr- Год назад

I just got a Neptune 2s and I don’t see the device on grid space

@MandicReally Год назад

Use the Ender 3. The Neptune 2 is an Ender 3 clone. The software knows no difference.

@Ice-vr- Год назад

@@MandicReally oh ok thanks for the help

@PZRGaming 8 месяцев назад

What about the elegoo neptune 3 pro?

@MandicReally 8 месяцев назад

Use Ender 3 profile and turn down the retractions for the direct drive. That machine is a clone of the Ender 3 with some better features.

@PZRGaming 8 месяцев назад

@@MandicReally Thanks! That is a good thing to know.

@pashaidzelchyk6284 Год назад

I have a ender 3 pro and it is not in the slicer

@MandicReally Год назад

Select Ender 3. There is nothing different from a Slicer perspective between the 2.

@Carside.1 7 месяцев назад

i couldn't find the ender 3 v2 neo

@MandicReally 7 месяцев назад

Just use the Ender 3 profile.

@Mikey_Fn_Spags 4 месяца назад

🧐 Collegeville BestBuy? That's worth a follow.

@i-took-that-picture 8 месяцев назад

the Voxelab Aquila X2 3D Printer

@MandicReally 8 месяцев назад

Use the Ender 3 Profile. That machine is a clone of the Ender 3.

@i-took-that-picture 8 месяцев назад

Thanks how do see my comment?

@i-took-that-picture 8 месяцев назад

Theres many more

@andrewlongfellow8745 10 месяцев назад

I'd like to see the cheapest computer running fusion 360.

@andreadraheim8104 Год назад

I have a Tina and I don’t now not to get stuff slyest

@femator1 Год назад

70$ for cromebook wow cheap not in Eu chipest 250€ 😪

@Launcherspider Год назад

I'm sure I made a comment. Why should It be deleted :(

@MandicReally Год назад

Don’t know what you are talking about. I don’t delete comments unless they are spam or mean. Neither of which I’ve had to deal with lately. I didn’t delete your comment.