No video :(

A180 Mercedes w176 MAP sensor How it Works / Clean / Removal absolute pressure sensors

Подписаться 55 тыс.

Просмотров 12 тыс.

50% 1

Playlist with more Videos about this w176 A180 :
• Mercedes A180 w176 Air...
This engine uses only MAP sensors to run the engine efficiently. On most of the other gasoline engines you will find a mass airflow sensor at the beginning of the intake , but not on this one . So it is important to know all the details about how they work and what is the relationship of the MAP sensor with other sensors in order to do a proper diagnose . There can be so much to talk about therefore it's possible that I missed some info .
Disclaimer :
This youtube channel: "doit_vehicles " can not guarantee that this information suits your car . "doit_vehicles " assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk .
#doitvehicles

Опубликовано:

26 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@MIKEYSREVIEWS 3 года назад

Have a BlueDriver scanner as well and helps me understand it even more. Great video!

@dannycrichton7336 3 года назад

My car looses power when I put my food down if the car in in to a high gear and I have to stop turn car off and back on and then it’s fine could it be one of these sensors bad? Same car as this

@mixofcolours8137 2 года назад

Bro can you make a video of how to replace the after air filter. sensor please??

@Cid156 Год назад

Nice video. Do you have a link for a cheap OBD2 scan tool?

@thirumurugan6014 2 года назад

Hi, Nice video. I have one question. My display shows 5.5l/100km calculated from 550km. I drove without stopping with max speed of 120km in highway. Real fuel consumption is 6.2km/100km. That is more 10%error. What would be the reason?

@mixofcolours8137 Год назад

Hi bro can you tell me how to clean the air filter sensor please thanks??

@Anzoo90 2 года назад

I put sport filter in my a180d and the engine light came up after some time it is show exaust sensor A & B ???

@666ChrisAsh 2 месяца назад

hello, which one of these sensors reads the pressure from the turbo? the one right before the throttle body or the one on the intake manifold?

@chrisisho2557 2 месяца назад

The one before throttle body

@bentleyvu8461 3 года назад

I have car it same , after change new map sensor they will work some time and lost power later , turn off engine wait 2 minutes engine on again they wirk fine , I think they short voltage do you guys know how to fix ? Thansk

@craigf6797 Год назад

whats the maximum pressure of sensor on the manifold?

@francofranzese2124 11 месяцев назад

this is not k9k engine, right?

@mixofcolours8137 2 года назад

Hi you didn't answer how to remove this first start pressure sensor please??

@evefurn 2 года назад

Happy new year. Very helpfull video and guide you have. I'm a subsriber from Australia, would you be able to give me guide regarding carbon cleaning with CRC intake valve and turbo cleaner, it says to be spray after maf sensor, but this car doesn't have maf, instead it have 3x map sensor, is it safe to use this type of chemical for carbon cleaning ?

@doit_vehicles 2 года назад

Happy New year! Yes it is safe to be use on MAP sensors

@danieleliasi3305 2 года назад

Hi. Any body have experience can help to solve this problem?? I have MB CLA 180 gasoline ( 117-342) the motor seems the same as in the above video. The car was stoped it in the garage for about 2 years. newly I changed both batteries, the starts and the auxiliary battery. But now when I start it the motor works well for about just 2 minutts then it stops totally, I try to start it again, the motor cranks but it wouldn't work. It works just with ( gas start spray.) It means that the electricity also ok. I must wait until the day after so I can start it again for just 2 minutts. I checked the bensin so it comes, but would not work.

@W.deutschmusik 2 года назад

Hello , i have a mercedes a200 cdi w176 2013 and i have P2540 code fuel low pressure sensor and i tried scanner tool i watched the pressure in fuel ramp and it gave me between 30000Kpa and 25700Kpa at idling and between 100kpa - 400kpa at primary and dies to 0kpa right away when i switch off the engine and then it come back to 100kpa-400kpa Can you please tell me if this numbers are correct or it's to much for the engine ,btw my car is slow now and i had a check engine light and a wierd cracking sound in the fuel pump when i switch on the key but not when engine on no wierd sound , is it the fuel low pressure sensor ??

@doit_vehicles 2 года назад

it does jump from 0 to 100 - 400 kpa after the engine is off ? the sensor looks way off the chart

@mixofcolours8137 2 года назад

Why not answering the comments??

@mixofcolours8137 2 года назад

Hi bro I subscribed you r channel please can you do some cooperation with me I have got a class mercedes a180 2014 petrol manual engine. Engine light came on I checked shows on my scanner Ho26.heater Bank 1 position is highe Exygen sensor monitor sensor 1 3 . Or sensors shows in problem? Ho26 heater bank 1sensore Exygen sensor How to find these sensors to replace them my car is same as yours??

@reesaoldyear7763 7 месяцев назад

Hi mate. I've got an a class 2013 petrol. It's a w176. Did you find the sensors you were looking for? I've the same problem as yours. Are the sensors all the same? I suspect I need to change one of them but not sure which one. If they're all the same, I could buy one and try on all three to find which one. But if they take different sensors, I might be running into an issue. Besides, it'd appreciated if you could share the links or details with me.

@mixofcolours8137 Год назад

This guy even didn't answer to one comment lol