Acura and Honda V6 Valve Cover Gasket Replacement With Basic Hand Tools

Подписаться 218 тыс.

Просмотров 70 тыс.

50% 1

A step by step guide on how to replace valve cover gaskets for Acura and Honda V6 engines.
► Subscribe: / carsntoys
►► Tools: www.amazon.com/shop/carsntoys
►► Felpro Gasket Set: amzn.to/3cYuKgL
►► Air Intake Hose: amzn.to/3liUysA
►►► Our most helpful videos (One million + playlist): • 1 Million Views Playlist
This will be helpful for the following models:
Acura TL Valve Cover Gasket Replacement
Acura MDX Valve Cover Gasket Replacement
Acura J-Series Valve Cover Gasket Replacement
Acura RL Valve Cover Gasket Replacement
Acura RDX Valve Cover Gasket Replacement
Acura TSX V6 Valve Cover Gasket Replacement
Acura ZDX Valve Cover Gasket Replacement
Honda Accord V6 Valve Cover Gasket Replacement
Honda Crosstour Valve Cover Gasket Replacement
Honda Odyssey Valve Cover Gasket Replacement
Honda Pilot Valve Cover Gasket Replacement
Honda Ridgeline Valve Cover Gasket Replacement
Note:
Any attempt to repair automotive parts and/or systems carries risk of personal injury. Always adhere and follow safe practices when working on vehicles. Such as, safety glasses, jack stands, no loose clothing, etc. No guarantee or warranty is implied. Use the information in this video at your own risk. Carsntoys is a member of the Amazon Influencer Program.
Publication, reproduction or distribution of this film is strictly prohibited.
Carsntoys
/ carsntoys

Авто/Мото

Опубликовано:

28 ноя 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 80

@Awayrook 6 месяцев назад

The best instructional video on youtube hands down

@pnweezy Год назад

Best one I see. That's the proper way of removing things unlike other videos they don't remove some other parts in the way jus work around n not disconnecting it. Like a lazy kind of mechanic

@theblacksaiyan7320 Год назад

Thanks to you and EricTheCarGuy I was able to do the rear valve cover gasket with little difficulty as without a vice the gromets are next to impossible to get off without completely destroying them

@johngraham6506 2 месяца назад

This looked easy until you had to strip out the interior, remove the dash, cut out the firewall, and unplug the entire wiring harness, then it looked like it was harder than I thought it would be! 🙂 Excellent video, one of the best I have seen on RU-vid. Great job!!!!

@shantor100 Месяц назад

You're confusing that with headlight bulb replacement. 3 hours minimum. Trust me 😅

@wolleyreikivalley 10 месяцев назад

i am about to do this on my TL! thank you for your help i really owe you baked goods

@jayhockley8841 Год назад

Nice video ! I had a 2003 S2000 ap1 . It was a blast but a little cramped for my size . Now I have a 2005 TL with the factory 6 speed , front Brembos and limited slip . Its almost as quick as my S2000 Was and nobody really trys to race me like they did in the S2000 .

@Demonfl6509 6 месяцев назад

Thank you so much 🙏🏻 prepping to get this done and I think I’ll get the other gasket as well while I haven’t done it yet and my oil leak isn’t too crazy yet lol

@evocre8r 2 года назад

This video was perfect! I was able to change both valve cover gaskets and cleaned up a lot of leaves and nuts in the engine bay (go figure). Tested it and no leaks. Thanks so much! p.s. any chance you'll do a timing belt change for the TL? Subscribed!

@HHECTOR3 Год назад

Great video.. helped out .. did my 2005 accord v6 3.0 … torque specifications 👍🏼

@mrleigh6969 Год назад

Nice work. I have to do that on my 2013 accord v6 (2dr). Only the front is leaking but obviously going to do both.

@kedst2000 6 месяцев назад

Excellent video! I have the same issue of my front wheels looking a mess due to the oil leaking. My bank 1 catalytic converter has gone bad, so I think I might do the converter job along with this and, if possible, pull the converter out past the rear valve cover while it is off of the car. I have read posts on Acurazine of people doing it that way. You are supposed to remove the drive shaft for the job but I have not had good luck removing the shafts on my TL. I have an 2008 with 206 k on it and it runs great. It will be cool not having my wheels looking a mess shortly after they are cleaned. Even more importantly, not having oil leaking period.

@aaronelder5080 11 месяцев назад

Nice work, I would have checked valve clearance while you had access

@franklynpertuz7669 Год назад

Nice work thank you show me a lot going to take me a little bit but I'll get it done

@NogodbutAllahh 2 месяца назад

Great video! Thanks for sharing!

@bryonslavin721 Год назад

Fantastic video thank you for the extra detail

@vincentperiolat4610 6 месяцев назад

Good video, lots of useful insights! Thanks 👍

@kizito8888 Год назад

To get the rubber gaskets out. Place the cover in the oven for about 15 minutes at 375 degrees. Once done, remove the cover and face it down. Get the flathead screwdriver and stick it in the gasket at an angle. Hit it with a hammer or palm. They will fall right out.

@heribertovalero 9 месяцев назад

Thank you very much for your help, you explain very well, thank you

@stevedm8962 Месяц назад

Fantastic video

@jaydenandrade4012 Год назад

Very good video well explained 👍

@dfields9511 2 года назад

Great vid I hate those plastic covers

@lbpwoody1 Год назад

@CarsNToys So did changing the valve cover gaskets reduce your brake disk dust?

@DaChapoGuzman 2 года назад

my valve covers are broken at the spark plug seal holes, would you think that the valve cover is interchangable? i have 05 RL

@kevinmetcalf6371 Год назад

Great video

@12volt_jayb Год назад

Would this be the same for 09 acura mdx?

@user-qh7ip6ju7z 2 месяца назад

Una pregunta se tiene que pulgar el aire acondicionado ohh no

@JaysonHoang14 Год назад

Lmfao you earned a sub for that bagel content

@chuchu-ee6fv Год назад

If you do my car , I don't ever feel like a ripoff. What a wonderful mechanic u are

@nighthawkj30A4 Год назад

This is the same exact way i removed and replaced my valve cover gaskets. You must have the Factory sm

@pietroscorpio3663 11 месяцев назад

Did you change the intake gasket as well or NO ???

@jpadilla0515 Год назад

I don't even own a acura or Honda. But this is some knowledge I didn't get at wyotech lol

@iceberglounge 4 месяца назад

Are there two plenum gaskets? I keep seeing bundles with two

@yvesleveque128 Месяц назад

What year is that Acura TL cuz I have a 2005, I know 2004 to 2008 are pretty much the same. But from what I'm told some have to head gaskets and then somehow just one. Or maybe I'm just mistaken

@willpage79 Год назад

Did you disconnect the negative battery?

@viewlesswind Год назад

Why not to clean the underside of the cover?

@eliasgarcia4793 2 года назад

Nice video !!!!!! Your are a “monster” 👏👏👏👏👏👏

@CarsNToys 2 года назад

Thanks 😆

@chrisbenson6860 Год назад

How long does this repair take

@mrc79 11 месяцев назад

Should we change intake manifold gasket while we're here? I have 250k miles. Just tryign to save labor and time. I rather do it all even if it's not broken.

@mine4751 11 месяцев назад

Do we also need to replace throttle body gasket? I have a pilot 2012

@balkee42 9 месяцев назад

Might as well

@gafurrzogaj1426 2 года назад

Why not clean inside of the valve cover also get all that gunk out make everything last longer and prevent engine sludge from forming in future 😉

@KeizorSoze1 Год назад

Would bad valve cover gaskets also cause any misfire issues? Because, I recently replaced all 6 spark plugs and coil packs and 3 days later, the misfire of banks 2, 4 & 5 happened. What else could be the cause of misfiring?

@JeremyFromOregon Год назад

Could be bad wires?

@KeizorSoze1 Год назад

@@JeremyFromOregon Ok. I haven't checked the wires. Thanks bro

@JayP19AD 9 месяцев назад

I know mines is misfiring bad, but I noticed a lot of oil on the backside spark plugs could be bad gaskets letting oil in???

@KeizorSoze1 9 месяцев назад

@@JayP19AD Yes. This time around, I had cylinders 1, 3 & 6 that were misfiring. I had bad tube seal gaskets. So, oil was all over those spark plugs and coilpacks. I just went ahead and replaced all 6 of the tube seals and valve cover gaskets since I had the covers off anyway.

@buddhaprince6773 2 месяца назад

⁠⁠⁠⁠@@KeizorSoze1did your car end up working good after you changed the tube seals? i have oil all over the coil pack in cyl 1

@drewmusic2991 6 месяцев назад

Where are the list of tools you used

@wilmarbarrick3194 2 года назад

Would've been a good time to check valve lash.

@johndeere1951a 2 года назад

Major omission no valve clearance and using old intake gasket. Don't fear buying oem Acura parts. Why comprise on quality parts when you bought a quality car. Felpro is ok when oem is not available.