Mate a correction on your nozzle size. The plastic nozzle with the Divet on the bottom is 250CC and not 500CC as your mention. The 500CC has a cupped end and 1000CC flat end. The kit comes preinstalled with 500CC nozzle. This is as per info and instruction manual of AEM 30-3313 V3 nozzle kit.
Should the nozzle be mounted on the bottom of the charge pipe( shooting up)? I imagine this to be safer so water cannot drip down into the pipe in the event of failure. Also, should the nozzle be at an angle or mounted 90 degrees into the charge pipe?
You can run pure distilled water in these kits. Pretty sure you don't need a tune if you run pure distilled water, but still talk to your tuner before installing.
@@ShabbernigdoXingjian You should be perfectly fine with distilled water injection, but I still won't tell you to take some random person's words on the internet. Try calling a race shop somewhere and ask on the phone. They should be able to give you all the info you need. If you want a tune, they might even be able to send you one over email after getting some data from your car. Good luck buddy.
I think water injection is better ,because you have the benefits of cooling and increasing octanes and you can tune your car with proper afr,with meth in the game afr is independent from meth that means you must have a second tune in the pocket for an empty tank.
I'm still looking into this but I'm finding that you can still target 14.6 and adjust the manifold air temp timing tables so once the meth starts Temps drop, timing advances, and narrowband adjust fueling. This wouldn't be for power adder applications because the ltft would have way too much fueling to pull back but in a fuel economy applications and increase octane support maybe could work. Please correct me if I'm way off not much info out there
Hi quick question ,just got my aem kit does the rear of your nozzle bit that connects to nylon hose have any play in it ,mine seems to spin slightly ...thanks
i have a question on the 3.8 gens how do i clean my valves ?? a safe way lol , also iknow u guys probably dont care but i made a edit acouple of years ago of the btr genny 😍
There are several ways but the most effective way is the walnut blast (many bmw performance shops will have the equipment as they are prone to this) also the water / methanol kit install will end up cleaning your valves for you over time as well. so if you don't feel like taking things apart and getting the cleaning done every once in a while, just get a water / methanol kit installed and have it steam clean your engine as you drive
Hello. I just purchased the kit for a Jaguar XF 3.0L SC. Running both upper and lower the car is turned up to about 450 Bhp at 18psi boost. I just want to make sure, because the chart says I should be running the 1000cc nozzle? Is that correct? I understand the settings on the controller as well, but how do I know if I’m spraying too much boost juice? Btw…I’m not tuning for methanol. Just want the cooler iats and knock control.
Sticking with what they recommend is an easy way but if you are looking for the benefits without tuning for it, running the smallest nozzle works just fine
One question please ,how do u install it on super charger cars do u use the same boost line or using the map sensor signal ,I ordered my kit v3 one the controller does not have the boost line
@@BTRcarcustoms do u recommend to ran the boost line set up or the map sensor signal ,because we had an issue for the map signal it was keep pumping meth into the throttle bodys once we turned it on and ended up motor damage 💔 ,we put a switch on and off for the kit and I don't think we should've ,any info appreciated
@@BTRcarcustoms would you suggest this, just your opinion do you think there would be enough gain for the money spent doing this? And would it work with the canned tuned from you guys
If your car has a stock wideband and target lambda system, you can run this without a tune. However this will most likely not give you much power gains without a proper tune
If you are tuned for meth, you want to stay on top of it. If you happen to run out as long as you stay out of boost until you fill up again it will work too
The V3 will flow the same depending on the nozzle. The difference is V3 offers better atomization. So more surface area for the water to cool temps faster. Also finer mist=better burn and combustion of the meth side of things. Faster cooler air+easier/more efficient combustion= more power
the water does the octant the methanol is a moot point do not even need it yea it stops freezing of storage water tank .i wish folks stop with teaching the novices technically wrong intell
Methanol accelerates evaporation rate in a short intake system. It converts to gas first and leaves behind a smaller water droplet. This more fine aerosol cools even better. Methanol helps system function. Water does most of the octane boosting and air cooling.
