AGA BMW N63 Valve Seal Tool 

Doing it right now 🤣😅

@@oneanonly2075 🤣🤣 best of luck I did it as well late last year reach out if you have any questions 👍🏻

Who has the timing procedure ?or does it come with the tool rental ?

@@ameerzeidan123 no instructions come with tools. These are professional tools and with professionals tools you are expected to know how to use them. I did this job year ago I do have experience with working on the cars. I used various different sources when it comes to timing the engine. I also did have BMW tech just phone call away when I got stuck. This give me confidence to do the job. Keep in mind he didn’t do any work. All he did was sometimes give me directions Best of luck 👍🏻

Hi, 1. We charge 20 hours if the vehicle is a sedan. If it is an SUV, we charge 21.5 hours. 2. Email me your contact info and address. I will help you find one. My email is Rich@agatools.com

AGA Tools do u guys have a shop. And where are you located?

AGA Tools Javier Casas 626 688 2654

@@AGATools Are you guys located in escondido? I have a 2006 bmw 550i that needs a valve replacement. rudykirsch@gmail.com

@@TheRudski We are. Give us a call at 760-738-4084 for more information! I tried sending you an email but lately our email has been going to spam.

thanks German Auto

how did you fix it I have a 02 545I having the same issue Estes158@yahoo.com Eddie

Hi Art. Because time is of the essence, we cannot produce a video that demonstrates removing everything inside the engine bay. The cost of also having a camera man record 35+ hours of video can get quite expensive as well. We made this instructional video with the engine outside of the vehicle is for a couple of reasons, one being that if the engine was inside the vehicle, you would not be able to get clear view of the engine and what we are trying to show you. If we made a video with the engine inside the vehicle, all you would be able to see are the cylinder heads and the technician working on it. We recommend this job for a professional technician who understands the basic concept of being a technician. Removing an intake manifold and using a leak down tester should be common knowledge for those planning to tackle this job. We understand that not everyone is able to afford a technician to perform this job, so we tried the best we can to capture the important details of this job and put it all on one video without having to sit through a 26 hour video after all said and done with editing and etc. However, if anyone were to have any questions, comments or issues while performing this job, we have a tech support line that is available from Monday through Friday 8-5 PST. This tech support line can be reached at 760-738-4084. For those who think email is easier, we can also be reached at rich@agatools.com Thanks!

So your gonna have a camera man for 35 hours of filming. Why does he get 35 hours to watch and the tech gets 25.5 for bending over and actually working! Its a good thing the N63 engine now cost less to replace than to fix.

Khalifa Khalifa Step 1: remove oil filter and check for small metal particles in the bottom of oil cap. If metal then replace engine. Step 2. If no metal then install a new vanos solenoid on the affected camshaft. Change oil and filter. Stroke the valve cover (bank 1) gently and say some nice things. Maybe you get lucky and its fixed. Step 3. If fault returns then replace engine. Step 4. Don't spend any money on an N63 trying to diagnose or check timing or replacing timing chains. Just buy a new engine. Step 5. Don't listen to anybody telling you that it can be fixed. It can but the cost is HIGH and the crank bearings with probably seize and fail shortly after. If its got more than 60k, then replace it. Look for discounted engine prices coming to a dealer near you.

***** thanks for your answer. This is 1L per 1000-1200km, not miles. Engine has no leakage and no white smoke from exhaust. Repleacing seals is possible without removing motor head?

***** thanks. You recommend or not recommend replace valve seals?;)

We use a white all purpose grease.

Ricky singh did you ever find anyone? If so how much was it?

@@jane1091 I know guy in Sacramento, CA who can do it for $2500

​@maximsafonov is this still the case? I think I need it done. I assume it's the same for the N63TU?

Kami, Please call our service department at 760-738-4626 so that we may gather more information to assist you with your issue.

We do not rent the tool out. However, we do have customers who are looking to sell theirs after using it once.

Kami, Please give our products department a call at 760-738-4084 so that we may further assist you.

Wholly fuck your English does not make any sense....... Brrrro

Santiago, we charge about 30 hours here in our shop, depending on the model of your vehicle.

Thanks for ur time...i have a 745 04

Santiago, it will be around 30 hours. Are you local to Southern California?

Florida

email is edtej158@yahoo.com

***** Thank you! for the information

the amount of work is insaneeee mess up once and it's over

Anthony Abelardo I can't imagine doing that 3 valve on each cylinder.

Ive done this job countless times as I work for bmw. The last quote I did just the labor was 8,000 dollars as it takes about 40 hours to do. And all german auto does a terrible job of how to do this. Some of the tools in the kit are garbage and nobody i know takes the injectors out because you dont need to.

Justin Skaggs $200/hr??

Mark, because of the limited space, leaving the engine inside the vehicle will not allow us to record every aspect of the engine.

Mark Ianuale Why the ALL CAPS man! He doesn’t have to show what he did, I am appreciative for what he does show us...FOR FREE!

@@canadiankrispybacon1450 lol I was at work. We use all caps for Reynolds.

Levi, you may use it once. But how many times are these independent using it? Many BMW workshops and independent shops have used our tools many times to provide customer with fast and reliable valve stem seal replacements. So if you think from an independent's perspective, they use this tool once at the rate of $2,500 for this job, they have paid the tool off the first time they use it plus made extra money. 2nd time using it is profit.

I'll rather spend $1,200 in this tool kit, and do it my self than spending $10k for a dealer to do it.

Id rather not get this engine in the first plaice, just crush untt burn itt

abelucious , it's mental don't wanna be involve in this at all.

Dam

How many hrs?

This is where our N63 Timing Chain Lock comes in. The chain lock will lock the timing chain in place so the engine doesn't rotate over, causing any damages.

You can use regular hand tools, that isn't the issue. Using regular hand tools will take MUCH longer as you will need to remove the engine, valve cover, timing cover, cams, timing chain and cylinder heads. Which most people don't want to do.

@@AGATools o really thanks imma give it a try