ALX Super 50 1st tank run in... 

u can mate.. its mad!

cheers bud ;)

thanks mate ;)

cheers ;)

cheers bro

RC Maxx UK I can’t wait for my brother and I to get our super 50’s. Nice bro!!!! I can’t wait to see a full break in run.

yes mate they are... i'm semi confident it might actually work! :)

;)

yes mate... just drilled the tank cap... ;)

thanks

will do bro

it was mate.... give you a rush for sure!

I love the sound of drp pipes.

me too mate. the sound is crazy! ;)

ALOT! its a heavy beast!...

cheers ! ;)

just tied mate... and the line was too thin.... ;)

who's there?

RC Maxx UK subbed

yes mate its standard shafts and cups wise all round. alloy cup in the rear and alloy housing. centre locker and alx/blackbone pin/ spur gears

George Specs I had done yes mate. A cpl of idle sets then left to cool. Tbh I did not go overly careful.

I mate! ;) the air filter setup came with the engine , along with the pipe. its a 'crazy stu' setup i guess, or very similar. So far, yes the zip ties are working... but i have lost a few rears due to them rubbing on the hub, so i will be using a small extender to offset the rear wheels slightly. should sort it ;)

Hi mate. the tank cap i drilled to put in a breather... return line is just cut with a screw to blank it off as its not needed... I originally put my breather on it but it just leaked constantly!

thanks mate. they are just mad max giant grips... with silverback beadlocks and cable ties to try keep the foams in! ;)

Ha, yes mate I am also looking forward to giving it some! tyres are an issue....with these big power engines but i am hopefull. I am planning to use my standard body ....also have a open style cage....

:)

its the tank breather mate ;)

its a Losi 5t mate.... ALX 50cc billet reed case engine

RC Maxx UK very nice! Thanks. How do you like the FID Center Diff Aluminum set up? Is it as strong as it looks?

George Specs did not exist when I got this engine mate.

Three years later and never got an answer to my question.

Bear Lambert hi mate. Hope your recovery is going well. This is just a losi 5t. Std chassis. I do now run the rcmax proam chassis which is a 3 piece and beautiful. I know you are in Canada but check out the rcmax web page, rcmodelz also. There are some cheaper , decent quality kits out there. These big bore engines though are next level money wise... and hard to recommend getting into unless you are really committed. My 50cc is an alx. There are also rcmax engines of course. Good luck!👍

@@RCmaxxUK Thanks for the reply, I would be interested in checking out that rcmax roam 3 piece chassis, As for recommending a 50cc motor well that is nothing I am well beyond that in my collection and all my gas motors, I have some super charged and even testing 1 a bit bigger then 50 cc with a turbo on it, I get a lot of motors from OBR, they make a hell of a motor custom to you and is tuned and reliable and you no is going to bring the bite with the growl they have, If i could sell all I have into RC I could probably buy myself a real race team, I think you might of misunderstood me in my comment, I have been into the large and giant scale RC stuff for well over 30 plus years, I ended up with a few giant scale planes and 1 jet and 2 big helicopters from debts others owed me that could not pay there bills, Like I said I already have a huge monster motor and electronics putting out a lot of power but just been having troubles finding a chassis to put into until I came across your vid and said that is the beast I need to put power into and give to my son as a surprise and kick ass and blow the doors of the completion by a long shot, Hope to stay in contact with you, because over where you are use have access it seems to a lot more large scale gas RC then we do, Mind you there is a big market here looking for it and I been doing my best building 1 off customs or kits as I am able to find them, Can you send me a link to that chassis you are using, because when I search it nothing comes up, Thanks again mate and hope to hear back soon, Bear.

@@bearlambert2806 ill get a link. check your spam comments as i think most link comments end up there. not trying to sound off... but OBR is nowhere near the kind of power these billet reed case 40-85 cc engines from rcmax and ALX are mate. look them up..... unless you are doing something very special to boost power ( which it sounds like you are ) ;)

@@bearlambert2806 www.rcmax.co.uk

@@RCmaxxUK Oh by no means did I say they were the best by far, I just happened to get 2 of there biggest motors they make with the pipes on both from a good friend of mine that deals with them a lot and he does not like there motors either so he gave me the pair for free, And I sent them to a top notch guy that worked on a lot of my ski-doo rotax racing engines , and I sent them to him to do his magic on them and he changed the heads and found better and bigger carbs to match the heads he put on and the piston and rings then ported and polished them both for me, He dynoed them for me I can find the stats for you if u like because I cannot recall off hand what they are putting out, but it is a hell of a lot more then OBR started and sent out, And he also has a super charger he developed to put on them and almost has fuel injection finished up for a 4 stroke, but that isn't what I was intending on a motor to use, I purchased an ALX 48 and it is just dying to come out to scream, and been really looking at the ALX 71 that 1 has caught my eye for a while now and seeing some trucks and cars just ripping it up with them was insane and had me sold right there and cannot wait to find something I like that I would want to put ir into, sorry my freind for the confusion, that is why it is so hard sometimes to type what you are trying to say or get across rather then speaking in person, And of course you sound just like myself if there is any way to get anything extra out of it I sure will be doing it, Speed is like an addictive drug once it bites you that is it, and for me it started young racing moto cross and also racing endurance type courses with quads, then when I was 18 years old I got the job of a lifetime, I got to do my apprenticeship which is a good fiend of mine now but I did my term in a drag racing shop and after I was certified he kept me on for about another 10 years until things just started dying out and there was not the people like way back then looking to build up there motors and drag race any more.

Hi mate... The filter seems good... but I did need to cut the side of my cage to get it to fit and its still tight! I do love the look of my alx and i am hoping 50cc is a good spot for power without destroying the drive train constantly!... we will see. I am sure you will love your 46! rcmax engines are also beautiful! petrol is std 95 pump. I have standard drive train. just alloy rear cup in the area alloy rear housing and a centre locker. alx own pinion and a blackbone spur gear. A mate runs an rcmax46 and we hope to drag them... same gearing to compare the motors at some point for a laugh ;) I'm learning myself mate. Any questions just ask.

I sure will stay in touch 👍🏾👍🏾

cheers ;)

Majid Akbar hi mate. They seem to yes.... I need to run it more... and harder to check it works. A mate tried zip ties on big digger tyres on his baja 71 alx. The ties survived but the tyres were destroyed quickly. I think on my 4wd 50cc they will work. 🤞🏽

it does buddy ;)

I will ! ;)

yes mate. can't wait to open it up!

dreams r good mate!

hey bro! what kinda vehicals you got and whats wrong with them if there traxas cant help you!

muggy maniac none mate had to sell continuous things broke and was young and stupid for selling. Last i had was a king motor baja all metal 29cc I customized nicely but was way to loud for my area and couldn't travel with it. I wanna get a brushless in hub motor beast oneday when I'm rich lol respects for your generous offer. peace out 🇬🇧✌😁👌🇬🇧

yeah... did another tank a day later.... next vid i will give it some ;)

;)