No video :(

Annual Motorcycle Maintenance Inspection

Подписаться 15 тыс.

Просмотров 7 тыс.

50% 1

Is your motorcycle ready for the road? Really?
Tire Mounting & Balancing • Easy Motorcycle Tire /...
Wheel & Swingarm Bearings • How to Change Your Mot...
Single Piece Brake Caliper Rebuild • Single Piece Motorcycl...
Nasty 2 Piece Brake Caliper Rebuild • Tokico 2 Piece Brake C...
Fork Rebuild • CHEAP Motorcycle Conve...
Fork Oil Flush SHORT • Motorcycle Fork Oil Fl...
Steering Stem Replacement • Motorcycle Steering St...
Wheel Alignment • Easy Motorcycle Fork A...
Soft Brake Lever Issues • Brake Master Cylinder ...
Brake Fluid/Clutch Fluid Flush & Clean • Brake/Clutch Bleed Tip...
Brake Cylinder Rebuild & Full System Bleeding • Rebuilding Brake/Clutc...
Getting Rid of Brake Drag & Cleaning • How to Cure Motorcycle...
Maintenance Air Cleaner/Brakes/Final Drive & Coolant Flush • 5 Maintenance Items Ev...
Charging System & How it Works • Motorcycle Stator Volt...
Testing 3 Phase Stator/Alternator & Regulator Rectifier • Battery Voltage / Regu...
Why Your Battery is Dead • Why your Motorcycle Ba...
Clutch Repairs • Motorcycle Clutch Repair
Single Side Swingarm Hub Bearing Service • Single Sided Swingarm ...
Driveline Spline Lube • BMW R1200 Driveshaft S...
Final Drive Service • BMW R1200 Final Drive ...
For the Lubemaster Caddy & More Good Stuff visit;
bikersrun.com/...
Receive Rod Rides & Wrenches Merch/Stickers/T-Shirts/Hoodies by becoming a Patron!
/ rodrideswrenches
Facebook & Instagram
www.facebook.c...
/ rodrideswrenches
#rodrideswrenches #bikersrun #motorcyclemaintenance
00:00 Intro
01:11 Tires
04:45 Tire Checks Tread Depth/Cupping/Air Pressure
06:45 Wheels/Bearings/Brakes
09:29 Forks & Seals Check
09:56 Steering Stem Bearing Check
10:29 Lights/Horn/Grip Check
11:08 Coolant Check
13:25 What's The Deal With The Air Filter
14:42 Battery & Charging System
15:42 Oil & Filter Change
17:27 Rear Tire/Brakes/Suspension
17:43 Lubing Up The Rear Suspension
18:45 Rear Swingarm Removal & Lubrication
20:00 Drive Shaft Splines & Final Drive Oil
20:26 Final Drive Chain Adjustment
20:42 Thorough Inspection Case of the Missing Bolt
21:16 Test Ride

Опубликовано:

17 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 32

@XLV750RD01 11 месяцев назад

Keep a maintenance log in Excel. Helps a ton, especially if you have more than one bike.

@Grudged1 Год назад

I have the original Dunlop TT 100s for my 1971 Triumph Trident. They are fine. 50+ years old. Like anything really, care and maintenance is all it takes. That said I also have them put away and ride with salt worthy Illinois weather sacrifice set. Also TT100s,

@bjrnhjjakobsen2174 Год назад

Good to see that your number of subs is moving. Your content is by far the best allround technical information on RU-vid. The editing is really Nice-keep up the good work👏👏.

@RodRidesWrenches Год назад

Thanks again Bjorn! 🏍

@tastydoublecapp Год назад

Just found your channel. Quality of content evident right away. Subscribed. Please keep it up.

@RodRidesWrenches Год назад

Thanks for the feedback & SUB! More in the editing stage right now.🎥👍

@diyeveryday67 Год назад

Good stuff! Thanks Rod. My F900XR is telling me it is time to clean the front calipers. Continuous brake pad dragging sound on front rotor when I move it around the garage.

@RodRidesWrenches Год назад

Yep that's the sound of reduced fuel economy and excess brake wear. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MdH_CwkE-nc.html Thanks for the view & feedback!

@cpuuk Год назад

No tire expiry date in the UK. Sound pre-season advice, thx.

@RodRidesWrenches Год назад

Thanks for the view & feedback. I was surprised how many people out there were saying that tires expire... Especially from the channels created by online retailers. Hmmm....

@ThatFifeBiker Год назад

There is a date limit, it will fail an mot after 8 years old am sure it’s 8 years now, never used to be a legal expiry date….

@SoloBlack313 Год назад

Thank you so much!!! LOVE the channel, you are the man!!

@RodRidesWrenches Год назад

Thanks for the kind words & view!

@sabiti5428 Год назад

Great overview with just the right amount of detail. Just wish it was the r1100rt

@RodRidesWrenches Год назад

hi Sabi, the R1100RT came apart when I did the clutch and throw-out bearing. Those videos are on my channel as well as the spline lubrication and so on. Thanks for the feedback & view!

@thodkats Год назад

Thanks Rod!

@RodRidesWrenches Год назад

Thanks for the feedback & view!

@BobLewis-zr1eq Год назад

What a great video. Thanks so much.

@RodRidesWrenches Год назад

Thanks for the view & feedback, I have a new video out Saturday, hope you will check it out! 🏍

@nick4506 3 месяца назад

like two years ago i got a angel st made in europe from 2010 with the world record sticker too, old tire worked great. thats just squareing off a tire you can ride around it by flicking the bike down past it, or running dramatically high tire pressure like 40/42 makes it less noticeable too if not recomended. I normay dont have that problem but my bikes that are exclusively for the canyons the fronts turn to triangles from trailbrakeing. same technique to ride around it but a little more concerning cause you have to go a little further. cuping on a tire is a wiered suspension/pressure issue where the leading or training edge of the tread is dramiticly raised makes each tread block look like a cup. you can experimentally find the perfect chain tension with a ratchet strap straping up the rear wheel so the rear axle the pivot bolt and output shaft are all in a line (the max tension) then just adjust it for a little bit of slack then just let it down.

@80a7x Год назад

Excellent video! I'll need to perform a few checkups on my bike in the near future, and this information will be extremely helpful.

@RodRidesWrenches Год назад

Thanks for the feedback and view! New video out this Saturday

@aidenmornay Год назад

Great video

@RodRidesWrenches Год назад

Glad you enjoyed it! New video out this Saturday!

@annonymous498 Год назад

Amazing video

@RodRidesWrenches Год назад

Thanks for the view & feedback, I have a new video out Saturday, hope you will check it out! 🏁

@erebus_nyx4294 Год назад

Great looking vfr! Great video! Can i ask what wind shield is installed?

@RodRidesWrenches Год назад

Checkout this ebay link, this is the one on the bike. ebay.us/IewCWG

@ajcole3353 Год назад

Love the content. Helps me with rebuilding a crashed st1300 and I love the bike! I want it back to it's designed ride condition but sadly at the moment she's far from it😔 got her in a sad state but I'm trying to breathe life back into her. Only problem I can't figure out is when I accelerate hard in 1st 2nd and sometimes in 3rd, it stalls and I HAVE to switch off the ignition to restart it otherwise it will just turn over if I hit the start button... Any ideas? Thanks for all the help and info man!

@RodRidesWrenches Год назад

If you cycle the key off and on after the stall as apposed to the engine kill switch (or vise versa) does it make a difference? If not I would start at the wiring harness, a lot of issues can result from a corroded ground cable. You may not be able to see the corrosion but if you cut the cable open it will be green with oxidation. Check the battery cables on both ends both positive and negative since this is a condition that can be duplicated by a loose battery cable. If the bike feels/smells (no gas) like it is being fuel starved, I would check the fuel flow back in the garage against the factory manual stat as you may need a new pump or maybe just a new filter. I would then check all the wiring connectors, pull the fairing and go through all the harness from the switch housings to the ECM, pay special attention to the fuel pump. Pull apart the connectors, inspect them for corrosion, clean up with WD40 & conductive grease. If still no joy, remove the airbox and check the connections under it, wring can get crispy under there. Run the harness and look for wear through the loom and wiring causing a short, but without FI Codes I would think the problem is relegated to the ignition itself, key switch, right handlebar switch or the fuel delivery, pump and filter. You have taken the right handlebar switch apart and cleaned it with WD40 already, right? Here is why this is so important ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-W0MTZbtMgOw.html - Good Luck!

@ajcole3353 Год назад

@@RodRidesWrenches while riding when I try to hard accelerate it dies then clutch in and I flip the kill switch off then on again and it starts. I'll admit I haven't pulled apart the air box or the fuel pump as I do ride it regularly as a daily rider and take it on long rides. I did have to go through the wiring harness to get it to run but not quite as thoroughly as you described. I get decent acceleration I just can't hard accelerate in 1st 2nd and the beginning of 3rd. I'm out of town for a month but I'll pull the air box and fuel pump when I get home. Right now she is without all the front fairings and I use my phone as a speedo since I can't mount the gauge cluster. I'll report what I find if anything... Thanks for the help.