I have one. I appreciate this video because I have yet to install it. I have a 48cc BBR Tuning on a 26" Switz Cruz bike by Bikeberry. I highly recommend the combination. When I built it your analog speedometer said I was going 42 mph. I installed your vapor recovery tube and your Vapor Expansion Muffler and Saw an increase to 55mph. Which I must claim / admit, scared the crap out of me.
I got my Arch tensioner before I got my engine kit, Mainly because I read too many horror stories about the tensioners that came with the kits. I've built 2 bikes so far and used the stock tensioners on the first, Which was a friends bike. One bent first time I used it, The other spring tensioner pulled the baring right out of it and it was sapose to be the tougher one. I have used the Arch on mine from the beginning and never had an issue accept the cheap bolts that come with the kit. I added a tensioner to the frame and connected it to the bolt to keep it from bending and its Bullet proof! Also welded my Arch to the frame, Just because I could.
Safety Tip. Do not use drill bits as punches and hit them with hammers as seen here. They are extremely brittle and will shatter and send razor sharp metal splinters into things like your eyeballs.
The problem I had with the tensioner that came with the motor drove into the spokes. While watching this video i would agree that it would solve the headache of a tensioner going into the spokes and messing another rim up.
Hey your videos are real clear , nicely explain and right to the point. Great job. I have a question the arch tensioner I got from Bikeberry has a 180 degrees curve at only one of the ends. Where does that curve goes on top or bottom. Also has two holes at each end of the arch chain tensioner .
you can put the chain on in a way simpler way. lock the clutch, thread the chain onto the engine sprocket, turn the sprocket with your finger and if your chain gets stuck on the sprocket cover just gently fish it out with a 2mm alen key, I use this method when I ride thru a part of the city where I cant use the engine (next to police stations and in more densely populated regions). When im in the countryside I just putt the chain on and go. There is one small catch, when taking the chain off in this way it sometimes gets stuck against the cover so I always have an emergency 6mm (I think) alen on me to take off the cover if necesary, this happened to me only once tho.
I find putting rubber from an old inner tube around there and then torquing down on it real hard it doesn't slip either.. and it gives a little spring action. So there's not so much slamming
These arch chain tensioner are a safer alternative to the dangerous stock tensioner. To me they do not address the issue of holding the roller from being angled improperly. The idea of keeping the chain roller from being angled imperfectly is unresolved. Yet, there's more alternative to tweek the arch so the chain rolls straight over the roller. In my opinion, the arch is a rather ugly attachment and there exists more perfect methods for of maintaining drive. (No chain tensioner, half links, and possibly the use of an engine mounted tensioner to account for the expected chain stretch.) My advice would be to delete the stock chain and install a hardened (racing) chain. It's much safer and doesn't stretch as much. Less need for constant adjustment. I've seen stock chains go out of adjustment after one or two rides, and when you think it couldn't stretch more, it does. It's not a frustration free set up. Hard chain and proper tension can resolve drive issues and restore worry free operation without attaching an ugly arch that appears to be useful for say attaching an alternator to a car engine.
Mine blew second ride lol chains scrap too break it with the pliers lol I ordered a 420 oring dirt bike chain cost 50bucks not 8bucks like that cheap one lol the hardware these engines come with is cheap it's like it's more or less to get the rideable and start changing to better more suitable parts great for a kid to learn with definitely wish I had one growing up but if I buy another I'm just ordering the engine and I'm gonna get the sprockets and chain from Kawasaki or Honda dirt bikes gas tank I have a few small ones from Honda cr 60cc I wasn't aware of all the design flaws and cheap hardware this was my first build expected it to be a little more durable like a real dirt bike lol could of bought 3 more engine with all the messing around and finding out the. Bugs in these like no rubber mounts at all lol no wonder everything vibrates loose lol every two rides I fixed that with dirt bike rubber mounts and locktite the exhaust is the thing comes loose once am awhile
Upgrade?? That should come stock with the motor kits... The tensioner/guide that the the kit comes with is bad injuries waiting to happen. Flops over into the spokes and the bike comes to a sudden stop. This should be stock, not considered an upgrade. Nonsense that the bikeberry company expects people to get hurt before they figure that out.
Bikeberry you guys are pretty pompous about these bike kits. Be honest for once. You should never use stock hardware that comes with any of the parts or kits you sell. Pulley tensioners are trash and a huge riding hazard. Tell them they need a frame that doesn't require a chain tension pulley. And not to trust any of the lead nuts and bolts to safely hold on the engine. Tell them they need rims better than the ones you sell while you're at it.