Arrma Maintenance Guide (Granite, Typhon, Big Rock, Senton, Vorteks) 4x4 3S BLX 

great video I just got into RC vehicles a few weeks ago. I have very limited knowledge on how these trucks work and run so watching this has been a HUGE help. Great detail in explaining stuff! Just bought Arrma granite V3 3s BLX for my first truck and it is super fun. Now I think I have finally found the channel I need to look after this toy to keep it running its best, After all, you get what you put into something.Cheers Pal thx

Really good video. I like the way you do your videos as they are simple to follow and provide great useful information.

Just the video I needed! A new Senton 3S and 6S owner here, about to upgrade the 3s to 6s specs before it's even rolled once. It's a motor, ESC and servo swap out, so seeing you pull the gear box apart gave me confidence on what's facing me. I've got a clicking noise on my drive shaft when the wheel roll in the same direciton. Spinning independently only sometimes makes the clicking noise. Looking real close, the rear right suspension is weakest, while the rear left is tightest. That's also true of side-to-side play, leaning the car one way, then that. The rear right suspension has a bit more sag and bit more wobble then the other three. The rear left is tightest on wide-to-side. The front suspension seems consistent to itself and is moderate between the rear extremes. I'm guessing I should tighten the right rear turnbuckle a few twists to nix the sagging. The side-to-side wobble almost plays like a loose rim shifting along the axle. The front wheels have a little shift that seems 'natural', but right rear has excessive comparatively and left rear has next to no side play. I'm glad I haven't run the thing yet.

*when checking motor mount screws, check side to side play of motor shaft* one of the two times my bearings failed in the stock motor, this is how i found it. if it gets bad enough the spur can fail even though the motor is still working(2nd failure lol)

Once again, another RazorRC video saved in my RC favorites folder.😁

During reassembly, I am having trouble pushing the pins in the steering knuckle deep enough in to replace the screws. Any tips? Thanks for the great video!

Very nice Bench clean and maintenance brother 👌 all mine are done and cleaned for the winder Hibernation 🦔 and they will be out in Spring 🌞 great tutorial video mate 👍😎👍

Good stuff as always. Your Granite seemed to toed out on both sides...more than mine anyway. Thanks for what you do.

Nice video. I usually don't go that far with disassembly. Lazy. I went through so many spurs with my BRCC but ever since I cut a hole in my chassis I never had a problem. Let's the dirt get out from motor area. Wish I had done it from day one. Good video

Yep ... Maintenance vids are guud .. im here watching for my typhon/SC Arrma

My granite is all gummed up from driving in sand. I don't know if it needs new bearings or just oil. But I think I need to take apart everything and clean out the drivetrain and differentials

I am having trouble pushing the pins back in to the steering knuckle deep enough so that I can replace the screws that hold them in. Any tips? Great video!

Shocks not leaking ! Mine do but they work good and it's easy .

Good video simple maintenance but necessary 👍🏻👊🏻👊🏻👊🏻

Thankyou so much. This helps astronomically.

Very well done! Do you have a set of screwdriver bits that goes with that screwdriver? It comes with a BIG Phillips/flat blade that aren't too useful for RC work. Do you think the modular design Arrma uses is that much better than the typical component layout in all other designs? Thanks.

Thanks, good maintenance "check list".

Is a maintenance guide coming for the TA Rival 10? Bought it recently and would love to see one.

Thank you Sir!! Love the Arrma 3s Videos!

great video and maintenance bro

Great video, i wish i could do it so quickly.

I am new to the this. I have a Big Rock Arrama truck. Accidentally hit the right side tire with a cement curb. Now my truck goes hard right. How do I fix that. I can see the cV is extended just a little. Any help would be so appreciated. Thank you in advance.

What kind of hour interval should we do an extensive maintenance like this? Provided its all normal driving conditions, no water.

Dude your chassie is way taller on the sides than mine. Have modifyd it yourself?

Which is this screwdriver?

i know im super late but is it okay to put assembly grease onto the motor gears under the gear cover? I know its good to have lubricants but didnt know if it would be bad if it got in the motor, thanks

Thanks for sharing my friend

Plastic drive shafts. Hm. How do they last in the long run?

The front diff on my Vorteks has a tight spot... gonna take it apart but not sure what I can do. Relatively new... 8 packs or so.

Hey Razor RC. Do you know the part number of that little plastic cover you put on the spur gear shaft? I need one.

Hey RAZOR I was hoping you could answer a question I had . If the vortek wing would fit on Granite V3 body? Any help would be greatly appreciated thank you.

I have a problem with with the motor fan it spins for a second then stop and the same thing goes on and went I give it gas it doesn’t do anything same for steering? Help plz Btw it’s a Arrma Big Rock 3s

At 7:00 I’m having trouble taking out the red thing and my rc car still won’t work😢

Very nice video bro ! Any grease recommendation for spurs, gears etc ?

What brand of electric screwdriver are u using? I got the new dewalt 8V max..will that work fine too on RC?

Is there supposed to be some in-and-out play on the slipper clutch assembly inside the plastic motor housing? I have probably 3/8" in and out after replacing the spur gear and dind't check if there was play before disassmbly.

Is it easy to convert the typhon 3s to a granite 3s??? All parts fits the chassis the same?..

perfect job mate..keep going💪

Great Job!!! Great video!!!

Great video 👍

Is your steering on reverse?

I can't get the pin out what would you suggest to try

Can you show diffs?

i noticed you dont have the center drive shaft support i broke mine (my first rc car only 2 days old ) do i need it to run the car or is it to run it without?

Awesome videos

What type of tires are those?

Where can I get that esc fan from?

Use a electric screwdriver for a 4mm long screw 😁 beter do it slow and never do the last turns with a electric screwdriver

I use my wife’s toothbrush

Hypothetically, let's just say your tab to remove your power module breaks because the damn thing wouldn't budge? How screwed am I? lol

If it ain't broke, don't fit it... ✌🏼🤠

I would have loved to watched this video, but I couldn't get past the nasty fingernails!!