Artillery Sidewinder Thin Wall Printing Setup & Review

Просмотров 81 тыс.

% 1 519

I will show tips and tricks for printing thin wall with this Artillery Sidewinder direct drive printer. I also print a full 3D printed RC airplane and give a review on the process.
Spool Holder STL: cults3d.com/en/3d-model/tool/spool-holder-troymcmillan
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: www.buymeacoffee.com/troymcmillanrc
See what else I am working on:
troymcmillan_rc
www.tiktok.com/@troymcmillan_rc
#3Dprinted,#RCairplane, #Artillery
Aliexpress store link：www.aliexpress.com/store/4697033
Artillery 3d official website: www.artillery3d.com/
STL Files for the ASK14 Glider: www.planeprint.com/ask14
How to Print Thin Wall: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-TZ_-AespXDw.html
Thank you to Artillery for sponsoring this video!
*These are the settings I used for this Artillery Sidewinder X1 with Overture PETG. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!
Profile 3 Cura Settings:
Quality:
Layer Height - 0.25
Line Width - 0.4
Shell:
Wall Line Count - 1
Infill:
Infill Density - 0
Material:
Printing Temperature - 240
Build Plate Temperature - 60
Flow - 100
Enable Retraction - Checked
Retraction Distance - 1.3
Retraction Speed - 10
Retraction Extra Prime Amount - 0.2
Speed:
Print Speed - 100
Outer Wall Speed - 35
Inner Wall Speed - 35
Travel Speed - 100
Travel:
Combing Mode - off
Cooling:
Enable Print Cooling - Checked
Fan Speed - 50
Mesh Fixes:
Union Overlapping Volumes - NOT Checked
Special Modes:
Surface Mode - Surface
Experimental:
Slicing Tolerance - Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Thank you for your support!!

Наука

Опубликовано:

23 янв 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 155

@artemnikitin2806 3 года назад

Congratulations on your SWX1! I had perfect results with generic PLA off Amazon right out of the box, however I started having issues with ABS, because it required bed @ 100°C all the time, at 100°C bed was sagging in the middle, so first layer on larger objects was a huge challenge, luckily I got it solved by using ABL, that though required upgrading firmware, I ended up using the stock Z axis sensor as ABL and whambam bulid plate -everything sticks to it rock solid at the same time its easy to remove without damaging thin wall prints. I tried using glue stick on the stock bed but 28hr long ABS came off with pieces of glass plate, Artillery was super nice and shipped replacement bed for free. So i highly advise using a quality PEI sheet like whambam. Also custom firmwares are mostly based on fresh merlin which includes linear advance, which is along with acceleration when tuned properly yelds super sharp corners and even sides at 100mm/s perimeters , 150mm/s infill and 65mm/s small perimeters with generic PLA.

@erickcoffin6848 3 года назад

This was literally what I have been waiting for...I have been contemplating getting this printer and comparing it to the cr10...but the direct drive makes a huge difference. I was wondering how well the sidewinder would do with rc airplane printing. You answered it. Thank you.

@fyzobaba 3 года назад

Don't think 2ce it's one of the best if not the best right now.

@mickydee6550 3 года назад

Just ordered the Artillery Genius, (and sent you three coffees.) Thanks for your channel!

@TroyMcMillan 3 года назад

Thank you so much Micky I really appreciate the support.

@mongini1 3 года назад

The Sidewinder is a good start. i got a heavily modified Ender 5 :) 2mm retraction for a direct drive is pretty huge. im at 0.5mm retraction at 30mm/s and got no stringing issues. For Bed adhesion i use a mirror with hairspray on it - sticks like hell when the glass is hot, releases itself when cooled down to 35°C. Works just as well for PETG, releases at about 45°C

@TroyMcMillan 3 года назад

Thank you I will try a mirror

@jctgf 3 года назад

So many variables, it seems 3d printing is a science on its own...

@Indiana_Caver 2 года назад

Hey thanks for goin thru your settings and process. I don’t have sidewinder, but I do have an ender 3 with a direct drive printer mod. Your retraction settings worked flawlessly on my set up with no adjustments and equal results. Can’t believe the quality thanks. No more stringing.

@DirtyBob2001 3 года назад

I use Elmers purple glue stick for adhesion. It really works, it's cheap and it cleans up super easy. A 30 pack cost me $8 on Amazon. All I do is run the glass print plate under warm water and wipe it off with a paper towel. Apply glue, print, rinse and repeat.

@wadebrewer7212 Год назад

I wish I would have found this a good minute ago. Trying to print 3dlabs P51D on a mostly stock Ender 3. Using Overture Silk Silver...and this has been a struggle bus event for sure. Finally got a good part last night. Still needs tweaked, but I am going to follow what you have done here, flow test and more importantly the retraction test. The silk material, finding out is VERY picky when it comes to retraction settings and not having the tip clog causing under extrusion. 1 mm retraction. 25mm acceleration. Retraction prime at 0.2. I think I can increase the retraction by 1mm and up the prime to 0.3 to deal with the stringing. Any more retraction than 3mm causes clogs and under extrusion with the silk on my printer. Thank you for sharing your set up.

@rustytyler1 3 года назад

That plane looks great

@jitendrajadhav9212 3 года назад

Hi, Troy, I Jitendra Jadhav from India, Aeromodeller since last 25 years, I am pretty impressed with your model

@TroyMcMillan 3 года назад

Thank you Jitendra, This is a fun plane to build for sure. Hello from Las Vegas

@petebard 3 года назад

Thanks Troy, I’ll be reading all your posts pertinent to building planes. I’m a junkie from way back.

@petebard 3 года назад

I was a bit amazed at how meticulous your revision of the Cessna 172 ??? was. I built the Aeronca Champ because that was the plane I soloed in (Jan 2, 1963, I’ve been around for a l o. n g time). Anyway I know where I want to put the printer but I’ve got a ton of old drones and never started kits in the way.also a never set up printer/XY carver whose bed was too small. Dunno when I’ll get the printer. It’s ordered but i hope it takes a week.bye for now

@Gixie-R 9 месяцев назад

Ive found for the Creality printers, Their own E-fit 3:1 direct drive extruder kit works great with their Spider hotends. They aint new and their nothing super fancy but thats why they work amazingly well. There also a great bolt on replacement for the baby KP3S kingroon which is great for printing the smalls for the RC planes. For the Enders you do have to adjust the firmware a smidge but a couple of sample prints later, youd be happy with the results.

@KaelumYodi 3 года назад

There are 2 things that you might want to try as well. First, don’t place the filament spool on top of the printer. With the spool up there, you have an inverted pendulum, which creates ringing, and could also be causing the imperfections that you discussed. Put the spool somewhere else and just run the filament over the printer. Second, try reducing the retraction distance even further, and increasing the speed to 60mm/s or higher. It may sound counter intuitive, but it usually works. I don’t have a Sidewinder, but on the 2 printer that I do have, I have the retraction distance set to 0.4mm, and the speed at 65mm/s on one printer and 100mm/s on the other. Have a great weekend!

@user-cm6tj2he4b 3 года назад

I assume you have a printer with direct extrusion?! I had pretty good results with an anycubic with Bowden. After calibrating the extruder, and slowing the print speed and decreasing the layer hight, I had really satisfying results. He's having some issues I have not seen yet. An interesting comment, particularly the filament roll on top. Makes sense! The anycubic has it on the side, but something I will think of when I will get another printer. Thanks.

@TroyMcMillan 3 года назад

I have noticed the ringing! I am going to be rearranging that area soon and will take your advice and mount the spool on the wall. Thank you!

@michaelbreen7756 3 года назад

I love my sidewinder as well. I’ve printed 5 planes on it now and I’m looking for my next project (plane)!

@NICHOLASRGLORIOSO 3 года назад

COOL! I just ordered one yesterday !!

@willielemaitre3854 3 года назад

Hi Troy. I have the Artillery Genius, also a brilliant printer! I printed 2 tubes that fits between the roll holder bearings. No more adhustment, all size rolls fit. Then, google acceleration calibration. It sorts a LOT of issues. I print at a speed of 60 with pla. Printed 13 planes so far, fantastic results.

@toddspeck9415 3 года назад

Awesome man. Thanks for sharing!

@batuhanomac8441 3 месяца назад

greetings from Turkey Troy, the Turkish tail registration has turned out very well.

@russvoege6735 3 года назад

What I found works best on glass, is from Vision Minor their Nano polymer. One coat lasts awhile

@breakalegfpv9532 3 года назад

I am a quad pilot, I just built my first wing and I think I should get a 3D printer. it just seems very involved, thanks for the upload

@ruftime 3 года назад

If you’ve built your quads.....3D printer is child’s play😎

@DirtyBob2001 3 года назад

A great start is the Creality Ender 3 for around $210, or get Ender 3 V2 with the better processor for $260-285. You need to swap out the springs for the bed leveler, I got 12 for $8 on Amazon, only need 4 of them. The springs that come with it are crap. New springs are a must. The micro SD card reader won't last either but you can get a good one for $10 or less. All kinds up upgrades including a direct drive for $40 or less if you catch it on sale on Banggood. For $250 you can extender kit and print big.

@breakalegfpv9532 3 года назад

@@DirtyBob2001 thank you ! and happy flying.

@breakalegfpv9532 3 года назад

@@ruftime i am going to take your word for it,, wish me luck !

@dooley9621 3 года назад

Great choice mate I have the Genius and the Sidewinder and have used them for over a year now. Common problems are the heatbeds, ribbon cables and extruder stepper motor. Replace them for quality items and your sweet. Have fun mate they print great.

@MrZeek101 3 года назад

congratts on the 10 k Troy great job Wow print turned out amazing and I agree with Hairspray works like a charm take care

@sotm6078 3 года назад

First mod to my Ender 3 was a direct drive Swiss hot end!!

@scottm5425 23 дня назад

10% white glue and water brushed on and dried with the heated bed. No adhesion problems at all. Can be cleaned off completely with rag and hot water.

@pascalperrin-bonnet7119 3 года назад

very nice

@EquinoxRC 3 года назад

Hey you better not beat me to the Savage Bobber maiden! Drives me crazy it takes me so long to finish one! Another great video Troy! Next time you place an amazon order get a roll of Sunlu SPLA, this stuff is awesome! It is a blend of PLA and PETG so it prints at PETG temps with minimal warping and a bed temp of 80+. It's all I build out of now. Best thing is they aren't brittle like pla and have a smooth and shiny look and feel. See ya!

@TroyMcMillan 3 года назад

Thank you for the recommendation I may try that out. You may beet me to the savage bobber maiden. I have mine all printed out I have not started assembling it yet. I may start the weekend on it. Cheers

@hpsie8310 3 года назад

Hi Troy, your prints look like on my Prusa :-) Awesome

@iraborton3941 3 года назад

I have an X1 version 4, I wound up adding a Z hop for moves to avoid the extruder tip catching on thin walls and the internal structures. I also us a 2 layer brim about 6-8mm around the part on some of the thinner pieces and they really stick good and don't warp. I then use canned air with a blow tube and the cool air pops the brim right off the bed.

@tommydee1437 3 года назад

I cant believe your cat dosent mess with all your stuff!

@SILVIOFRANCO1 3 года назад

That is awesome. Congrats

@willielemaitre3854 3 года назад

And try a good hairspray. One thin layer on a clean bed. No adhesion issues again

@abyssalreclass 3 года назад

Agreed. Once I switched from the stock bed on my ender 3 to a glass bed with hairspray, I've never had an issue with adhesion or lifting.

@TheholeyRanger 3 года назад

@@abyssalreclass I prefer to use ender 3 magnetic flexible build plate

@samdu6914 3 года назад

I have had the X1 for 3 weeks and I can say that there is no need to use hairspray because the ultrabase has micro holes which make the parts adhere well even if they are high

@alpaslanalperkayar 3 года назад

what brand do you use? UK brands?

@samdu6914 3 года назад

@@alpaslanalperkayar you can even use amazonbasics PLA. you just have to clean the bed with isopropyl alcohol after a few prints. but the most important is the adjustment of the bed!

@colincollier3355 3 года назад

Thanks for the info. I'm very happy with my Sidewinder but I can't get my prints 100%. I might try your settings.

@nathan1sixteen 3 года назад

For PETG, cover the printer with a bag or something. It will help keep the heat in and should help with adhesion

@GrantFarrell 3 года назад

You hit the algorithm with this video, been recommended it aggressively. Dope channel, very cool.

@englecam 3 года назад

Nice review Troy

@alienxyt 3 года назад

Bravo!

@itsme-tm4vd 3 года назад

excellent

@SomeGuyInSandy 3 года назад

Nice! It does look like a good printer.

@aussieparamotorman9931 Год назад

Hey Troy, I’ve been watching your channel for a while now I’m a huge fan of your content and it’s been heaps helpful. I’ve also noticed that on some of your planes you have awesome custom decals. Do you have any plans on making a decal video? Totally should man! Thanks

@MW-fy6pi Год назад

build all planes like this and with a clear Canopy that is the best on this plane

@iraborton3941 3 года назад

Here's a great tip, you can blow canned air right where the brim is stuck on the bed, the air coming out of the can is cool and will pop the brim right off of the glass bed, no spatula needed.

@TOURNOIS.Racing 3 года назад

Hi, the glass is PLA or PETG Print? it's verry clear :) Thank'bye

@TroyMcMillan 3 года назад

The clear is PETG.

@hrangfd 3 года назад

เครื่องมือสุดยอดมากๆเลย เป็นโรงงานผลิตขายแบบเล็กๆได้เลย👍👍👍

@santiagoblandon3022 3 года назад

Have you tried Linear Advance? It makes wonders for flow control and makes printing thin wall prints like these waaaay easier to fine tune

@mopesca 3 года назад

especially on corners it makes a big difference, no more bulky or round corners.

@ripmax333 3 года назад

Hi, sorry for my stupid question, but what do you mean by linear advance ? Another type of printer, program? Or something else’s? Can you please explain. I’m very tempted to start 3D printing.

@santiagoblandon3022 3 года назад

No problem, Linear Advance is a feature you can activate in the firmware of the 3d printer(given that the control board has enough memory left) that compensates for the compresion on the filament path. So the bulgy adges or the underextruded starts of extrusion paths disappear. Look up "teaching tech linear advance" in youtube. He explains it better than I can :D

@517cliff 10 месяцев назад

I use a brim on almost all pieces it’s easy to remove.

@mudnsavy 3 года назад

So I can’t get the stringing to stop with the LW-PLA so have been doing one part at a time on my printer (ender 3 pro). I can get a good .40 wall with the cube but can’t for the life of me get the string test to come out well at all. Do you use 1 wall only on that too? If I increase the retraction it does it all before it moves off the part. I wish Color-Fab website would talk about the ret settings.

@alanjones4747 3 года назад

Upgrade the Bowden to DD next. I have a Microswiss on my Ender 3. Very good.

@vincentrichard2703 Год назад

Wich filament do you use at wich temperature ? Amazing results !👍

@excellenceinanimation960 2 года назад

Can you do a tutorial for making parts and plane in fusion or whatever program you use.

@clubaeromodelismograncanaria 3 года назад

Buen video. 👏👏👏

@laurent3091 3 года назад

Clean the bed with rubbing alcohol after each print and you will no longer have a problems with parts not stcking

3 года назад

just clean the surface before printing. dust on the air is sticking when the surface heating. the same dust sticking to the filament and it is obstruct the nozzle.

@did3d523 Год назад

Ineed good tips to make window of a Bell 206 enought clear to put camera inside

@Shadow-Hawk 3 года назад

Hi! Was wondering if you could print a 1974 Grumman American AA-1B Trainer?

@user-rx8qq8sk9ydv1ce5ib 7 месяцев назад

Awesome! Thanks. please share if there are good websites to buy from them the 3d plan stl files. Do the plans come with building instructions or power setup requirements or I will be left with a bunch of plastic pieces and I need to guess which ones go together? I ordered p1s and looking forward to start and learn about building rc plains. Did you use light pla or normal and usually how many filaments you need up build one jet/airplane of a wingspan of 1500mm. A lot of questions! Thanks

@gilsalerno4401 2 года назад

Congratulations, plane looks beautiful, do you sell? I really liked this red

@petebard 3 года назад

I’m hooked. I ordered the printer. But how about advice on designing structure? I’m interested in pretty small models so I shouldn’t need much and RC gear and a tiny video cam dictates some needs. Oh well, I guess I said what I have to. BTW, I’ve been flying for about sixty years. Started with an Otarion superregen and an SE-2 escarpment. Bought propo gear as soon as it came out. Never flew reeds.

@petebard 3 года назад

Damned spell checker. That word is escapment

@TroyMcMillan 3 года назад

@@petebard Smaller planes definitely don't need much inner structure. I printed a small UMX timber and did not have any inner structure in the fuse and on part in the wing. Good luck with the printer and with your builds.

@mickydee6550 3 года назад

Hi Troy. You listed your settings for this printer for Overture PETG. Would those same settings apply to Overture PLA and LW PLA on this printer as well? Does the USB drive included with this printer already have CURA installed, or is that a separate purchase! Thanks for your help. I will be using your link to buy a Artillery Genius printer tomorrow!

@TroyMcMillan 3 года назад

Thank you for using the link I appreciate that. Cura can be download for free. ultimaker.com/software The only difference for printing PLA is turn the temp down to 215c everything is the same. For LW-PLA turn the flow setting down to 53% and temp to 235c.

@GraemeRobinson 2 года назад

very interesting Troy - are you still using this printer? How is it holding up? Would love a followup review.

@hpsie8310 3 года назад

I used Sunlu TPU , but in comparison to Varioshore it strings like hell

@pomanpomahovich9265 2 года назад

пора коту самолет собрать )))) обидчиво кот смотрит вечером точно заминирует)

@jeremyferguson9292 3 года назад

Out of all of your printers right now which do you like best? I see you have this one, an Ender 3 V2 and a an anycubic Vyper (maybe a few others). Which is your favorite, I am about to buy my first printer.

@rcdavidk 3 года назад

Great video... thanks. Would you recommend the SW-X1 as a first printer? I was going to wait for Prusa to release their MK4 but I don't think that's happening for a while.

@TroyMcMillan 3 года назад

Yes I would recommend the SW-X1 or the Genius is also a good first printer.

@Joakester 3 года назад

What decal did you use. Is that something you were able to print at home? Love your channel!

@micheyggg 3 года назад

Print on kapton tape and you'll never have adhesion issues again.

@yoyodec69100 Год назад

Hi Troy, can i use a Artillery setup for my Ender 3 S1 PRO (Direct Drive)... 😀

@ericbarker3850 3 года назад

Hi Troy, I’m new to your channel. I’m going to purchase my first 3d printer. My budget it max $500. How happy are you with the Sidewinder, after 7 months? I hope you will reply. I’m learning so much from you. If you will reply, I promise 3 coffee’s right away. I want a direct drive printer, to start with? Do you think that is also wise? Let me know what you think of your sidewinder and if you would recommend something else, and why. Thanks

@purplemonkeydishwasher9360 3 года назад

Do you use the standard 0.4mm nozzle for your prints or have you experimented with different sized nozzles?

@TroyMcMillan 3 года назад

I just use stock .4mm nozzle.

@pascalperrin-bonnet7119 3 года назад

Moi j'ai réalisé les avions de 3dlabprint.

@poltid 3 года назад

Is it better than ender 3 v2?

@ahmetomersaid985 2 года назад

It hasn't been a year since you bought it, but it malfunctioned, how do you like it?

@russelltiede9076 Год назад

I’m interested in starting to print planes parts. I have a 3D printer with a small print area that i will use for now, but will need to upgrade before long. Is the Artillery SW-X1 still you go to printer for planes parts? It looks like the SW-X2 is the current version available would it be a good option?

@AerialWaviator 3 года назад

What are your thoughts on the Sidewinder? (8:05) all parts fit on 200mm x 200mm area when referencing the Overture pad. Genius has a 220 x 220 x 250 mm bed.

@vincentrichard2703 Год назад

Do you apply an "outer wal wipe distance" in Cura ?

@Decrypt_Symbol 3 года назад

Plan?

@pacomb 3 года назад

No Z wobble? A 1kg roll at 50cm height makes a lot of wobble. That is why people fit braces

@kenpappas9520 3 года назад

What is the weight vs foam?

@TroyMcMillan 3 года назад

PLA is 40% heavier than foam

@LaurenceCampbell 3 года назад

Hi Troy, my thin wall pla is looking pretty good now thanks to your videos helping me tune it. The only remaining issue is some minor pock marks on the flat side of the test piece which occur from about half way along the section up to the z seam. More prevalent at the top 3cm where the overhang begins. Any thoughts?

@TroyMcMillan 3 года назад

Pock marks can be fixed by slowing down the print. They can also be caused from moisture in the PLA. If the PLA is not a new role then it can have moisture and pop when it goes thew the extruder causing pock marks.

@LaurenceCampbell 3 года назад

@@TroyMcMillan thanks Troy, the pla is new, so guess its speed. I will give it a try.

@TroyMcMillan 3 года назад

@@LaurenceCampbell I usually print at 35mm/s

@LaurenceCampbell 3 года назад

@@TroyMcMillan yeah, i was at 55m/sec on my sovol sv01. Will try slower.

@PsychOut101 3 года назад

Do you use linear advance in combination with those print settings?

@Chris-vc1dh 3 года назад

Hi Can you tell me please what I am doing wrong? I got files from thingerverse of a wing part and put it to cura and scaled it as it was a bit too big and put preview and it was not printing the outside skin only the inside when I reset scale it was printing everything.

@scottflanagan3129 2 года назад

Is the X2 a good substitute for the X1 you use in the video? I'm interested in this printer based on your comments, but sometimes the new versions aren't as good as original.

@jaaninfotech-ok 3 года назад

Hi Sir, I have the same model of 3D Printer (Artillery SW-X1). Plz suggest me the software for this printer because its standard model present in its Cheche like its Logo are just printed through this 3D printer but when I'm trying to be printed from my Laptop then it doesn't print. Plz suggest.

@TroyMcMillan 3 года назад

Try using Cura to slice it!

@TheholeyRanger 3 года назад

What is the difference in size between that printer and the Ender 3?

@TroyMcMillan 3 года назад

This printer is much larger than the Ender 3.

@TheholeyRanger Год назад

Ok thanks

@cosmicoverlap 3 года назад

Hello, is the Artillery Sidewinder better than the Prusa 3D printer in printing aircraft wings?

@TroyMcMillan 3 года назад

I don't have a Prusa so I can't say for sure but I have had people comment to me that I have been getting just as good or better quality then Prusa printers. This printer works very well for printing airplane parts.

@ahmetomersaid985 3 года назад

Hello. Is 30 * 30 * 40 3d printer suitable for this type of RC aircraft? What would you recommend?

@TroyMcMillan 3 года назад

you need 200x200x200mm build plate for all the planes on my channel. I would recommend the artillery sidewinder or genius.

@ahmetomersaid985 3 года назад

thank you very much

@clementgoetke2385 3 года назад

do you know anything about foam pla or wood pla i have seen it advertised ?

@TroyMcMillan 3 года назад

I have used the foam PLA but have not tried wood pla

@paulmason6847 3 года назад

Hi great video, have you tried the supplied g code from 3D lab print on this printer for lw-pla? Or do you alway slice your own with cura

@TroyMcMillan 3 года назад

I only slice my own setting. I did not try just loading the G code

@paulmason6847 3 года назад

@@TroyMcMillan I have just printed the Albertross from 3dlabprint in lw pla using the supplied g codes and it works fine on the sidewinder x1. Finish looks fantastic

@TroyMcMillan 3 года назад

@@paulmason6847 Nice thank you for letting me know that is awesome to know that the files work for the sidewinder.

@johnkearney9339 3 года назад

@@paulmason6847 Did you make any changes to the printer I have one coming and hope I can print out of the box with gcodes

@paulmason6847 3 года назад

@@johnkearney9339 no changes, it just prints right from the G code, only thing I found was due to the shape being long and thin for the wing sections - I would get a little warping near the ends, I stopped this by using masking tape on the bed, never normally use masking tape but it works fantastic.

@sudarshanpujari5503 3 года назад

How is direct drive helpful?

@TroyMcMillan 3 года назад

less stringing and less retraction

@timothygiggey1610 3 года назад

How do I go from a design in autodesk fusion 360 to the 3d printer? Will the slicer put in the joints to glue the components together or is that done at the design stage?

@TroyMcMillan 3 года назад

it is done in the design stage, you have to do that in fusion 360

@timothygiggey1610 3 года назад

@@TroyMcMillan that what I was thinking. I purchased the Artillery Sidewinder and some PLW & BLACK TPU for some tires I WANT TO DESIGN. I have been looking for LW-PLA but not have much luck just white looking for gray for my B-52 W/8 32mm EDFs I purchased the glider you featured on utube that will be my starting point thanks for your help

@TroyMcMillan 3 года назад

@@timothygiggey1610 yeah check out fusion 360 for designing them, it works great. It's a lot of fun when your design is printed out too :) the glider is an amazing plane, good luck with it!!

@kevinfacascuntom2385 3 года назад

f86 f2 sabre

@ahmetonurongur4995 3 года назад

turkey tail number :D

@johnkearney9339 3 года назад

Hi Troy what program are you using to convert 3d lab print object files into gcode thank

@TroyMcMillan 3 года назад

I use Cura for all my prints. You can slice 3d lab prints planes in Cura it is a bit more difficult to get a good print.

@johnkearney9339 3 года назад

@@TroyMcMillan thanks i am new to this and cant get a good print with 3d lab files i will stick to others until my skills improve

@charlesrestivo870 3 года назад

Cant print that hot I get a nozzle temp shut down

@charlesrestivo870 3 года назад

Ender3v2 changed out orginal hotend to new one dont get them as often but I still get them

@OsvaldirVargas 3 года назад

👍👋👋👋👍

@flaviobastos8356 2 года назад

Olá eu compro

@FreeBirdFPV 3 года назад

how you glue PETG its impossible

@TroyMcMillan 3 года назад

medium CA glue

@FreeBirdFPV 3 года назад

@@TroyMcMillan not holding split out

@EnglishTurbines 3 года назад

Alternatively, you could just install a direct drive on the original printers...They are without doubt, the worst I've seen...🤔🤔😳

@TeamTable Год назад

Great video, but P L E A S E get a proper microphone!

@superbmediacontentcreator 6 месяцев назад

You offer some good ideas but your audio sucks... buy a good wireless and when you do your edit listen through headphones since your levels are inconstant. One minute the level is too low and the next you blew me away.

@RARenfield 3 года назад

$400 printer and you're wrapping the bed in masking tape?!? Open the door to the room and the draft kills 12 hours worth of printing?!? Yea, this is really mature technology. They should include a Commodore 64 to run it. I too can print a model of the Icon A5. For the cost in time and waste of an actual Icon A5. You are to be commended for your patience.