BAFANG what grease? how to apply grease? gear grease ebike 

Brilliantly explained 👌

Very nice! I always wondered how to pull out the shaft in BBS02. I would lube the gears while they are out to avoid applying the grease on the walls.

Nice video. Thank you 👌

very nice never knew this

Best one of these Bafang re-grease videos I have seen. Well done!

That grease is designed for nylon.. He could have used any grease for those gears and should have opened it up and used that Mobile 28 on the nylon gear.. They have very little white lithium grease on them from the factory.

znajomy garaż , pozdro Marcin ')

What is the torque setting for the two rings on the other side of the bottom bracket shaft? Torque setting = Knock it round with a hammer and a screwdriver

it's better to lubricate that shaft while you have it in your hand. Good video, thanks !

Hi how many washers did you put between the spider adapter and the motor? Thanks!

Very nice you video!! Just one question, where you buy the spare part for your motor Bafang? Thanks

Hello sir, thank you for what you offer to serve others. This is a virtuous act.Please I want you to help me if you can. My bike has become very heavy. Where is the problem in your eyes, mechanical or electrical?

Great video, very detailed. Just wondering what the solution was that you used to wash the old grease off? Cheers.

what chain do you need for this motor? 1/2 "x 3/32"???

Useful and I need to do this, but the two bearing nutted rings using long nosed pliers looks a bit on the agricultural side to me. Is that the best and only way? Type of grease and method of application with bare fingers suggests this is not a 'pro' method or approach. Is that fair comment?

Hi, I want to know, what liquid did you use at time 1:40 , also, can I use the same liquid for internal components as well (example: All other bearing and stuffs)? if this is not the best, what type of liquid are better and safe to clean? Thanks in advance!!

What is the best type of grease?

Can one actually do this maintenance with the motor still attached to the bike frame? It would be sooooo much easier to handle the greasing part, but I figure the screws etc. might not come off easily..

Can i use SUPER LUB?

Did you use a degreasers to clean that?

I now have a Lekkie motor cover that has this tiny ‘grease port’ where do I get a grease gun or zerk that small?????

This is the proper way how to re grease wash 1st because small metal sediments is in the old grease if you just simply add instead of preventive maintenance you just making it worst good job sr

I hear Molykote pg 75 is the best. Mobil 28 seems to be the most common in videos.

How often do you do that?

How often is this required? I have a BBS02 currently at 725km... was thinking maybe 1000km might be worth it?

Very good and detailed video of re greasing. But if you ask me, you're definitely use way too many grease on the granny gear.

Can't see clearly which side of the bearing must go upwards.... :/.

In the bearings and in the gearbox, the same lubricant???

This is BBS01 or BBS02?

what liquid did you used for cleaning the gear

I just ordered a motor, is it best to do this straight away or after a certain amount of miles?

Any good synthetic grease should be fine

Can this be done whilst the motor is still on the bike?

Can you drill & install a small zerk whilst its apart??

Grease red or black guys?

Can i use SLIPKOTE??

Did u grease the nylon gear too? Is that necessary?

mobil 28 ist just the WRONG grease for anything other than super high temperature bearings. you need a tacky, yet fluid grease for gears, nobody cares about the million degrees temperature resistance of this mobil 28. your motor will stop working lightyears before that grease even remotely gets warm. but the gears will definitely wear out because it doesn't stick to the metal and has just about the worst fluidity. get some high tack grease (e.g. calcium complex synthetic longlife grease), add some viscous PAO oil (best is 220-320W) and if you wish, some dry super lubricant like PTFE or WS2. I don't understand why so many people keep recommending mobil 28 for bafang motors. the lubrication effect is gone after less than 1000km whereas a proper grease with high fluidity basically doesn't require any regreasing for 10'000s of km therafter.

thank you mute button.

01:58 NOOOOOOOOO...now you've pushed dirty grease and solvent down to the nylon gear and bearing. 03:31 apply grease to the big gear before installing.

you didn't prove that by changing the grease the noise is gone.

Can't get that gasket out for the life of me been trying hours

Why no gloves?