Тёмный

BARNES 4WD Jeep JK 1Ton Steering Install w/ 

Squatchy Offroad
Подписаться 2,1 тыс.
Просмотров 2,7 тыс.
50% 1

My wife & I install Barnes 4WD ‪@barnes4wd‬ JK 1Ton steering and Rough Country ‪@RoughCountryTV‬ steering stabilizer on her 2014 JKU.
Barnes 4WD Link: barnes4wd.com/...
Rough Country Link: www.roughcount...
▶️ #ROCKTHESQUATCH: www.etsy.com/s...
▶️ #GETSQUATCHED: / squatchyoffroad
▶️Get Squatchy With Us: linktr.ee/squa...
#squatchyoffroad #jeep #jku #barnes4wd #steering #roughcountry

Опубликовано:

 

15 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 12   
@tracyallison237
@tracyallison237 Год назад
I am really leaning towards the same system. Wish you guys would have gone into what your measuring and why. I would have missed the nickle grease. Good tip. Thanks for the video.
@SquatchyOffroad
@SquatchyOffroad Год назад
We measure stock length from center of tierod end to center of tierod end on the tierod bar and drag link bar so we can get new setup close to same length as the stock setup and then afterwards we measured tire to tire and set toe end and adjusted drag link bar to center steering wheel and get close enough to drive until we could get a true alignment done. Hope that helps some.
@tracyallison237
@tracyallison237 Год назад
@@SquatchyOffroad Thank you. What is the back space and off set of the wheels? Barnes requies some wheel measurements to work
@dsteck5888
@dsteck5888 Год назад
I am putting mine on and the only way I can clear my steering stabilizer bracket is to flip the drag link at the steering knuckle
@SquatchyOffroad
@SquatchyOffroad Год назад
Do you have a aftermarket stabilizer bracket on the jeep?
@dsteck5888
@dsteck5888 Год назад
@@SquatchyOffroad I do.
@SquatchyOffroad
@SquatchyOffroad Год назад
The kit is made to run with stabilizer in stock bracket on axle. Last kit I put on the jeep had a aftermarket stabilizer bracket and I had to remove it and put back in factory location.
@jdawg2474
@jdawg2474 7 месяцев назад
So how have you liked the barnes setup so far and have you had any issues with the jam nuts staying tightened?
@SquatchyOffroad
@SquatchyOffroad 7 месяцев назад
It has worked flawlessly. I have installed the same kit on several customer jeeps and all have been very happy with it also. Great kit for the money.
@jdawg2474
@jdawg2474 7 месяцев назад
@@SquatchyOffroad that's good. I've ordered this kit in the flipped version to go with my new lift that I'm about to install.
@GULIVERSOFFROAD
@GULIVERSOFFROAD Год назад
do you have a stock track bar bracket or do you have a relocation bracket?
@SquatchyOffroad
@SquatchyOffroad Год назад
It is a aftermarket adjustable track bar in stock location.
Далее
다리찢기 고인물⁉️😱 Leg Splits Challenge
00:37
Barnes 4WD Aluminum Tie Rod Install!
17:01
Просмотров 39 тыс.
DIY One Ton Steering: Jeep JKU One Ton Swap Episode 6
20:33
Building One Ton Steering (Barnes 4WD)
11:28
Просмотров 32 тыс.
Worst Jeep Mods || Don't Buy!
7:17
Просмотров 645 тыс.
2 5 TON Aluminum Tie Rod and Drag Link | RPM Steering
12:51