I’m so glad I found this video. We’ve just taken delivery of a Beko WTK104121A. The instruction booklet AND a supplementary sheet (stressing the point as an “important note for product installation”) both explain that “when you turn the product on for the first time, calibration mode must be run”. Considering that this is the first thing you have to do, these instruction barely even hint at how you’re supposed to do it. Without finding your video, I’m not sure I would’ve worked it out.
@@Liedragon Sorry, only just seen this. If I remember correctly, it was just a case of pressing the Spin button underneath the display. Hope you found it.
Doh! Missed this completely when the machine was installed by AO three weeks ago, and of course their installers don't check for the extra bit of paper with tiny print on that say to run this before anything else, hopefully it will still calibrate in whatever way it is supposed to after 15+ washes have already been done in it. 😬
Oh so that's the "calibration mode"... Hmm.. i tried what Washerboy said in his hidden check mode thingy on a Beko Homewhiz pro version thingy (with eco 40-60), prewash and steamcure, it did nothing... Too bad this doesn't work in my arctic :(
Danas kada sam Isao u omega shop po grijac za nasu Beko susilicu vidio sam onu Slim susilicu i sokirso sam se kada sam je vidio nisam vjerovao da postoji Slim susilica
They are at home. This is washer and dryer in our new apartment where sisters are going to stay :) Basically moving from apartment where Indesit and Vox are
Hey , I immediately need an answer. Do we have to use dishwasher salt with Fairy capsules if water is hard ? I use fairy on Bosch dishwasher and sometimes I see lots of scratches on glasses and artillery. I don't choose very high temperatures and I leave blanks between dishes when placing them. And spray arms , filters are always shiny clean. What to do ? Could you please help me ? And if we have to use salt to soften the water , would salt and detergent together leave too much chemicals on dishes ?
Its not needed to do it. But if you want- turn washer on, hold prewash button until it shows 90°C 600rpm, then turn off spin. It will take 15 mins. Then start
Calibration mode is to adjust the water that machine uses with the laundry weight. You won't see nothing but something is happening when the machine is washing
wait WHAT 🤯🤯🤯 I never even realised you could select no spin on drum clean 😳 I thought it only calibrated on the main program lol 😂 mine lasts 15 minutes think I’ll do that on mine now and see if it’s the same as this 😅 (and also record the full cycle)
I think it shortens the time... Beko WUE7611D XAW, the first 10 washes I didn't do that calibration, because I didn't know it had that function... I didn't see the special paper on which it says that... So before the calibration on the program "cotton 90°" , with an almost full drum, washing took 3:15 hours, and after calibration with the same amount of laundry, it takes 2:45 hours. I don't see any changes with the synthetics 40° program. I don't use other programs, so I can't say.
I have a problem, I have this washing machine model, but when it is running out or in the middle, it increases its duration, does this happen to anyone??
I am trying to follow these instructions but whenever I try to press on the SPIN button in order to wash with no spinning it doesn’t work 😢 it stays on 600 help!!!!
I'm shocked! My washing machine doesn't have calibration mode😩😩😩😩😩😩😩😩😩I can't understand why, it's not an old model…..🤕🤕I wanted to try on clothes to see what was going on😂😂
No this is different, Its for the calibration of the machine that is required before its first wash. Its in the instructions manual, its so the machine can sense the loads properly... thats why its only 15 mins. the drum cleaning programme is much longer, usually around 2 hours give or take depending on the machine...
I’m gonna tell you a story of about getting a new washing machine So we don’t have it yet but very soon we will We currently have a Samsung but the drain hose is clogged you might be thinking oh why not just unclog it We have actually been trying to unclog it but we are not able to so I think for are new washing machine we’re gonna get a beko too also I subscribed to you The only difference is we are not getting a dryer
@@truthhurts4913 Why... what specifically is wrong with them... because I know a lot of people who have Beko refrigerators and washing machines, and they all work well... without some malfunctions that are no more frequent than with others... then what and why is wrong with them? New appliances from brands that were of the highest quality 20 or more years ago, today work worse and break down much more than that Beko, because they were all sold to Chinese corporations and install the last crappy components... the best example of that is Gorenje. I have a 3-year-old Gorenje refrigerator, which cools very poorly, and is very noisy, twice as noisy as the 20-year-old one. Only Elektrolux and Bosch may be better because they are not yet completely Chinese.
@@bogdannb Samo da još više ne smanjuje razinu vode... jer i ovako vrti skoro pa na suho... na pranju jedva da se vidi voda na kraju bubnja. Ne znam dali je kod svih novih tako, jer sam do sad imao 23 godine staru Gorenje WA412, otišao je programator... pred 3 tjedna sam kupio Beko WUE7611D XA... i ne znam još kaj reć... jedino je dobro šta mogu sam dodat još malo, do litru vode kad ona završi svoje namakanje.
