Bending machine Ka panel banane Ka tarika | panel kaise thik kare 

Thank you sir 🙏

Thank you so much 🙏

Ok sir jarur 🙏

Thank you so much sir 🙏

Thank you so much 🙏

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ssQ_RkgPqzA.html

Sir machine per depend karta h ki aap ko kis machine ke liye panel bana rahe ho . Agar aap simple machine ke liye bana rahe ho jisme sirf 2 contactor 2 limit switch push button emergency switch rahte hai to apka kaam 5000 Tak bhi ho jayega Wahi agar aap Spartan ya uske jaisi machine ke liye panel bana rahe ho to aapko 20000 se 25000 bhi kharch karne pad sakte hai 🙏

Ha bilkul bus contactor ki oprating coil per A2 per dono contactor me Neutral dena hoga jisse 220 volt mill jaye .Baki same rahega . Neutral sirf dono contactor ki coil me A2 me dena h jo dono me ek hi taar se lup hoga

Bhai meri ek problem solf kr do please bar bendar machine ki 🙏🙏

Problem Batao sir 🙏

Ha g 🙏

सर किसी से अच्छे से चैक करना पड़ेगा क्योंकि अगर आपको मशीन के पार्ट्स और प्रोग्राम के बारे में कुछ नही पता तो आप उसे ठीक करने में परेशान हो जाओगे

Holding supply contactor ke NO pe permanent milti hai

@@s.k.electrical9862 to auto mannual selector switch kha lagayein? mere pas selector switch both NO element wala hai.

Auto manual ke liye bhi ek video h hamare channel pe aap ek bar try jaroor kare 🙏

@@s.k.electrical9862 Sir vo video dekh chuka hun, par is uper wale video ki wiring k hisab se or selector switch mai dono NO element ek sath push hone wale condition mai kha lagaenge ye bas janna tha. 🙏🏻

Dono contactor me se jo forward h uske NO me limit switch ( jaha se cut hoke machine wapas aati h ) ke NC se jo wire aata h use auto manual ke thru lete hai aur reverse Contactor ke NO me Jo wire Home Position ke Limit switch ( jaha aake Machine rukti h ) ke NC se aati h use auto manual switch ke thru lena hai .to is tarah limit switch se aane wale ye wire pahle auto manual switch me lagenge aur auto manual switch se contactor me lagenge 🙏

Break contactor me supply Reverse Contactor aur Forward Contactor ke NC se hoti hui jati hai ise check karke dekho kahi NO Me Break ka taar galti se lag gaya ho 🙏

Ok aapke sawal ka jawab jaldi hi dekhne ko mil jayega 🙏

Ok aapke sawal ka jawab jaldi hi dekhne ko mil jayega 🙏

Isme apko 2 cheeje check karni hai pahle ye dekhna ki Break contactor on ho raha hai ya nahi agar nahi on ho raha hai to aapko 24 volt AC check karke iski opreting coil me pahuchani h jo timer 2 ke NC se aati h Dusra agar contactor on ho raha h aur break Kam nahi kar raha h to apko 60 volt DC check karke dekhna h jo contactor se hoker motor me jati h 🙏

Spartan machine ki hamare channel pe ek video h usko bhi try karna ho sakta hai aapka Samadhan ho jaye.

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-jvhlkPTiJwk.html

Sir do din intzar karo video aa jayegi

Kaam ke hisab se lambi ho jati h poora samjhane me time lagta h na Aur waise bhi ham abhi kam experience wale h 🙏

Ha g sir starting me galtiya ho jati hai Hum ye video better quality me jaroor banayenge

Video upload kar di hai usme aapka doubt clear ho jayega jaroor dekhe 🙏

Sir control wiring me kahi problem ho gai hogi Dono contactor ek saath hi oprate ho rahe honge to apko ek baar agar apse ho sake contactor me se jo taar motor ke connection ki taraf lage h unko hata kar check karke dekho aur agr wo dono ek time per oprate ho rahe hai to unko thik kare 🙏

Sir 12se24 ghante chalane ke baad jal rha hai

@@sandeepgupta7763 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-V8PiCka_UrA.html

@@sandeepgupta7763 Sir aap dono contactor ko interlock Karo matlab ek contactor ki oprating coil me supply dusre contactor ke NC se Hoker do 🙏

Sir aap ne pahle se interlock Kiya hai

Sir m bhi kahi naukri hi karta hu aise to phir sabse baat nahi kar paunga jiska phone nahi uthaunga wo hi gali dega 🙏