BMW e46 Oil Catch Can Install

Подписаться 62 тыс.

Просмотров 61 тыс.

50% 1

This video is about installing an oil catch can in place of the factory flawed crank case ventilation system (CCV). So far I have not mayo/mustard substance in my valve cover, the catch can has caught it all. I have increased vacuum in my valve cover which is re-seating the piston o-rings for less blow by keeping oil consumption down. I have also noticed the car revs easier and quicker which is always a plus. I RECOMMEND replacing your VCG, oil filter housing gasket, oil dipstick tube o-ring.
Smash that LIKE button and be sure to Subscribe!!!
Links to all the parts shown/used in the video
Catch Can: amzn.to/2TKsDWT
PCV: amzn.to/2FkLJty
Doorman 47080 3/4'' to 5/8'' adapter: amzn.to/2TieAlY
SharkBite 5/8" to 3/8" adapter: amzn.to/2Ol96GB - fits despite having different size on Amazon
Doorman 650-005 or 47395 3/8" oil dipstick tube cap: amzn.to/2TJCGvf
12 pack of clamps: amzn.to/2Y8pLBn
Heater hose can be found at any auto parts store
3 ft of 3/8" ID heater hose
2 ft of 5/8" ID heater hose
1 ft of 3/4" ID heater hose
Optional parts, you can reuse your old but I recommend to replace:
www.fcpeuro.com/products/bmw-...
www.fcpeuro.com/products/bmw-...
www.fcpeuro.com/products/bmw-...
#BMW #e46 #CatchCan This description contains affiliate links. If you buy a product through my custom link, I will earn a small commission at no extra cost to you. This video is for entertainment purposes only. Evan Goyuk assumes no liability for any repairs or modifications performed by the viewer as a result of the information contained in this video.

Авто/Мото

Опубликовано:

29 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 119

@calikid4612 3 года назад

Just finished putting my catch can!!! Thank you for putting everything in the description. I ordered everything I needed. And got it done I’d say an a hour. Wasn’t hard at all. But 👍🏼 on the video.

@EvanGoyuk 3 года назад

Great mod and helps drastically reduce oil consumption

@outtheboxproduction.7733 4 года назад

Installed over 20000km ago, no difference, need to add same amount of oil, good thing is that without original ccv oil for sure isn't going back to intake as it was before. Strongly recommend. 330CI E 46

@MARVELB3ATZ 4 года назад

Appreciate the modified diagram awesome work

@EvanGoyuk 4 года назад

Glad it helped you

@davidwegner2070 4 года назад

1st time I'm replying on RU-vid to anyone after years of watching Evan. I purchased an E46 partly because of you after a year of research. Just letting you know I appreciate your help. Now that I took the time to actually sign in, I might keep in touch, if I can figure out if you replied or not, lol. Be cool. (the diagram was very helpful)

@EvanGoyuk 4 года назад

Hello David, congrats on the e46. The best way to reach me is via Instagram @EvanGoyuk

@davidwegner2070 4 года назад

Cool. Give me a few years to figure out my Instagram accout and I'll get in touch with you. :) Thanks for getting back to me. Have a nice day.

@BryanChance 5 лет назад

I've been wanting to install oil catch can!! Can"t wait til this weekend to try it out. Thanks man. Looks like alot of work.

@EvanGoyuk 5 лет назад

It’s not too much work but well worth it

@korishmax 5 лет назад

All those plastic crack becomes after a high temp under the hood. The working temp of your m54 is about 105 Celsius. Make a cold thermostat to cool down your engine to about 90 Celsius and change your engine fan to electro - it's also helps to take more extra HP from your engine and extend water pump life.

@mike.135i 4 года назад

how do u “make a cold thermostat"

@tribewu3223 4 года назад

Cold thermostat ? Lol theirs no upgraded thermostat for the m54 mishimoto makes ones but it's shit it doesn't fit to a oem housing. A electric fan is better but doesn't keep your engine cooler unless you put a controller on it. ( Which u shouldn't need to if you' aren't making way more power and tracking it) The thing you can upgrade to your water pump to a Stewart or a 3 row radiator

@cmontoibiza 3 года назад

m54 ecu is programmable, find your local programmer and he will make your car working with 90 celsius.

@COFFIE-in4fd 3 года назад

@@tribewu3223 you can upgrade the oem thermostat to "colder" one by putting some 4mm ball under the rod of thermopile. I've done it on my M54 and the working temperature now is about 90

@emergencylowmaneuvering7350 3 года назад

put more holes on the stock thermostat for more liquid flow. It might have a bit less MPG but less hot too..

@steve60usa 3 года назад

What did you do with the rear fitting that goes along the top of the intake? Is it sucking from front and rear? Or did you plug the rear one?

@georgesmbyd6603 5 лет назад

Please install an OEM e60 short shifter and make a video about it :)

@407_ryan8 10 месяцев назад

excellent diagram

@therealzooch 5 лет назад

I just use a small 1/4 10mm socket to get that first top plate off rather than take off the cabin filter and all that, just reach under on the left.

@M1r092 5 лет назад

I'd love to see a follow-up on this when the catch can is filled up and how long it took for that to fill. I'm currently having vacuum leaks cause of the CCV system and I am considering changing over to a catch can...

@jorgemiranda822 5 лет назад

I install a catch in my 330ci for about 2 years now , and from 1 liter of oil every 1000 km to nothing , no more adding oil at all ..

@pugnutter8715 5 лет назад

I got the same result replacing my CCV 🤷‍♂️

@joefowler9600 3 года назад

@@pugnutter8715 did you have any other signs that your ccv needed replacing apart from high oil consumption? I have very high oil consumption on my 2.5l m54 engine, also thinking of just replacing the ccv like for like so still stanard set up.

@tituschase4074 3 года назад

You probably dont care but if you guys are stoned like me atm then you can stream pretty much all of the new series on instaflixxer. Been streaming with my brother these days xD

@aaravraylan5253 3 года назад

@Titus Chase yup, I have been watching on instaflixxer for months myself =)

@blazegunner2385 2 года назад

Just one question normally on the pcv valve threads go onto valve cover and nipple to intake manifold u put it the opposite way.

@bouba958 2 года назад

Can you communicate the different references and make of the fittings with diameter of the hoses, with search links?

@jamesrmore 4 года назад

Where in your video do you show the vacuum connection to the fuel rail area? Are there two vacuum ports? Do you have to block one? What do you think about using the vacuum port at rear of engine instead (It is currently simply capped)? Seems this would be much simpler especially if it is providing same vacuum. Don't have to use the fancy plastic connectors.

@EvanGoyuk 4 года назад

Yes there is one vacuum port with a cap on it and another with a line attach going to the SAP system. I just need re-did the like that already had a vacuum line it going to the SAP since this line gets cracked.

@besofacacia6103 4 года назад

but that sucktion seems to be dangerous. any car i have seen with that kind of sucktion needed ccv replacement. correct me plz ?!

@nicosmith9312 4 года назад

I watch a series of videos from you and alot of others regarding different topics on the e46 im a new e46 325xi owner and im sooo stokked to finally have the car ive been dreaming of since young

@abrahamarmendariz908 5 лет назад

I have no suction through the oil cap but the car runs smooth

@user-ec8jo2gx9d 2 года назад

What is that second hose for on the manifold when you start to disassemble at the beginning

@hammadrehman4257 4 года назад

need to do this on an E60 body (525i) any difference between doing it like this and on an E60? Thanks!

@alexikreviasuk2473 2 года назад

can't find the 5/8th to 3/8th adapter links not working got another link for one?

@dohyunkim5328 3 года назад

, the M52 has an additional vacuum line attached to the Fuel Pressure Regulator. Has any one done a catch can on an m52? If so, how did you tie in the Fuel Pressure Regulator vacuum line

@e36fanatics 3 года назад

hmm this is something id like to know too...

@snivesz32 4 года назад

You probably have a clogged CCV, that's the original problem. If it were working the vapor would be removed from the oil and you wouldn't get the sludge.

@matreyia 3 года назад

milky oil cap is normal if you drive short trips...especially in cold weather.

@zachv1035 3 года назад

Shouldn’t be

@matreyia 3 года назад

@@zachv1035 - it is. water did not get heated to evaporate so mixes with oil vapor and milkifies. It's totally normal chemistry and physics. Now if this is milky after an hour of driving in summer...you got a serious catastrophic issue with your head gasket.

@GokuTheHusky 2 года назад

I have a p0171 p0174 and i think its th ccv so if i do this will it still throw the codes?

@jamesrmore 4 года назад

How often are you needing to empty your can? Are you getting any water vapor condensing in with the oil ( your original mayo problem)?

@EvanGoyuk 4 года назад

Every couple months in the winter very rarely in the summer. It did 100 percent solve my water vapor condensing issue and reduced my oil consumption!!!

@williamgreen9280 2 года назад

@@EvanGoyuk How much oil consumption did you have before vs after? I haven't done this mod yet but I did purchase turner motorsports oil catch can kit. I currently burn about 1qt per 1k miles and my car does not have any oil leaks.

@Vexulus 4 года назад

There’s a guy named 50skid on RU-vid he has better angles and explains way better he probably got the idea from him cause this is the exact setup he does

@jetreg5843 4 года назад

🤣

@uhyeahitsme413 3 года назад

The more people making vids, the better it is for us e46ers. Quit hating, make a better one yourself if it's so bad.

@Vexulus 3 года назад

@@uhyeahitsme413 no one asked or cares

@FieldClosed 5 лет назад

I followed all the same steps you did and I still have a vacuum leak, but when I did it the way Nathan's diy garage and the 50's kid did it I didn't have a vacuum leak but my catch can was getting too hot to touch, but that was a cheap like 25 dollar one so I figured that was the problem because it leaked anyway so I got a mishimoto one for 130, installed it the way you did and I'm still sucking air somewhere and I can't seem to figure it out. Someone please help!!

@e36fanatics 3 года назад

if you have bad valve cover gasket it may be cause... in fact id replace all gaskets and see if the problem is still there

@vchain6884 3 месяца назад

So on pcv valve the side I cannot blow trough should face the hose that goes into Intake?

@nicosmith9312 4 года назад

Hey @evangoyuk what was the song used in the video itsz sik bro i tried to shazam but no results...

@Recon77 6 месяцев назад

I’m looking to do this as well with my E46. This doesn’t cause any CEL, correct? And is it necessary to have a baffled catch can?

@Recon77 6 месяцев назад

any update or follow up? still running this?

@bamsr9051 3 года назад

Good video. Some video just point here & there does not help so much. 👍👍👍

@tonylou8424 5 лет назад

hello good job what is the name of the song you are playing in video plz ?

@MrDanielsahne 5 лет назад

Nice video. Thank you. Whats the Song at 3:20? :) Greetings from germany

@muddersbach 4 года назад

MrDanielsahne Sad Money x Nyne - Can‘t Sleep Alone Greetings from Germany 😝

@DiegoFlores-sx7nr 4 года назад

Was your car blowing out white smoke from the tail pipes..???

@EvanGoyuk 4 года назад

Yes, it was the CCV system. So if yours is smoking you need a new CCV system.

@COFFIE-in4fd 3 года назад

The engine is knocking. It has some diesel sound. May be the Vanos needs to be rebuilded or smth

@vexed_con 3 года назад

More than likely it’s actually the hydraulic lifters. They tend to get noisy when not in tip top shape, but not a huge issue like bad vanos or rod knock

@Grezzley 4 года назад

Add the line from catch can to dipstick with valve that let it just go only from catch can down :D its prty awesome

@willmckinney2768 4 года назад

You should make an update video 👍💯

@EvanGoyuk 4 года назад

Great idea

@bobafittness1346 4 года назад

Please do so.

@michael_e46s21 5 лет назад

I need help, what did I do wrong , also it suck to much air when i lift the oil cap is that normal or not

@EvanGoyuk 5 лет назад

That is normal

@michael_e46s21 5 лет назад

My engine still idles also

@BossAutomotriz 4 года назад

Hi Evan, how it is working now?

@EvanGoyuk 4 года назад

Still working good

@markpapolopucus3640 4 года назад

Dude, theres major knocking in your engine, low oil, maybe lifters? Any check engine lights? maybe its the recording device but it def doesn't sound good

@EvanGoyuk 4 года назад

It’s lifter tick

@ntshikapeter6124 3 года назад

I think you should also consider about Vanos Rattle Kit. I've just learned about it

@glenglene8473 Год назад

I think you installed the PCV backward.

@mike.135i 4 года назад

can i use a one way/check valve in place of the PCV u have?

@EvanGoyuk 4 года назад

No!! The pressure is different I wouldn’t know risk it. I know this one works

@mike.135i 4 года назад

okay thanks for the reply, i bought another PCV valve because i think mine is too small. i bought one thats made for a 6 cyl ford engine and is about the size of the one you are usuing so ill see if it works

@chungheekim961 4 года назад

@@EvanGoyuk Hey thanks for the video Evan! I was looking at the Amazon link for the PCV valve and it says it doesn't fit my car (2002 330i), but I figure it will say that just because it's actually not part of the car, but is necessary for the project. Can you confirm please?

@EvanGoyuk 4 года назад

That is correct but it will fit. Please use my link as it helps the channel

@chungheekim961 4 года назад

@@EvanGoyuk Yep will do! Thank you!

@dohyunkim5328 3 года назад

hi dear I have got m52tu engine . my ccv have fpr vacuum hose if I delete my ccv then where I can put it in my fpr vacuum hose plz tell me I have done m54 oil cathch can but m52tu engine it have problem the fpr vacuum hose so what am I have to do!!

@e36fanatics 3 года назад

id like to know answer to this too...

@jeffgroller4352 2 года назад

There is vacuum ports mid way down back side drivers side of engine they have vacuum caps you can use one of them

@sundaysgarage 3 года назад

Installed a catch can, put the pcv in the wrong place and blew my engine so fun

@emergencylowmaneuvering7350 3 года назад

What.. wrecked it??

@sundaysgarage 3 года назад

@@emergencylowmaneuvering7350 almost blew the headgasket, definitely lifted the gasket in one channel and got a lit of white smoke from coolant in the engine but i caught it quick enough so its fine, just make sure that goes in the right spot

@GPerformance710 2 года назад

@@sundaysgarage I can’t imagine where you placed it for that to happen. Was it placed on line from intake manifold to catch can where it should be but backwards or something ?

@sundaysgarage 2 года назад

@@GPerformance710 thats exactly it lmao my buddy put it in the wrong way so i was jusy constantly building pressure lmao

@sundaysgarage 2 года назад

@@GPerformance710 only ran it for like 10 seconds tho and i notice it was jot sounding right

@sydewayzmo3905 2 года назад

So much easier to do on S54

@tobitobi5625 5 лет назад

first XD 😆 keep going bro 💪

@williemickbillie 4 года назад

So how’d you block the ccv system below?

@EvanGoyuk 4 года назад

By unplugging it

@williemickbillie 4 года назад

Evan Goyuk ah I feel ya. All open ports of the system are plugged so the open oil separator doesn’t matter staying on

@williemickbillie 4 года назад

Evan Goyuk literally finishing mine tomorrow ty for advice

@williemickbillie 4 года назад

Evan Goyuk is there any electrical plugs that go to the oil separator? Like any electrical plugs you unplugged?

@DriftSpec. 4 года назад

hey im a little stumped here, where does the out go to on themanifold

@EvanGoyuk 4 года назад

There is a tube on the left side of the intake manifold you take the connector off and cut the hose. Reuse the connector

@206dcoe 2 месяца назад

Song name??

@mavricxx 5 лет назад

When you have that mayo type oil in your oil cap it means your valve cover gasket is done

@rghmods4466 5 лет назад

no i had that when i was stock and it was from condensation i live in a cold climate i even got the cover gasket replaced and still had it, after i did my catch can it was all good !

@EvanGoyuk 5 лет назад

Same here the cold climate

@rghmods4466 5 лет назад

Evan Goyuk hey Evan I love the videos! Can you tell me the kind of head lights you have and a install video? I’ll look and see if you already have one but just asking ! Thanks

@rghmods4466 5 лет назад

Evan Goyuk just kidding I just watched the vid, haha I would recommend you change your vanos oil line it looks very rusty and the boot looks ripped it’s a cheap part and easy fix I replaced mine took about a hour, my car was pissing all 7 quarts in like 20 mins and it can fuck up the car! Just some preventative matienance

@EvanGoyuk 5 лет назад

Thanks for the tip! I will look into doing it

@michael_e46s21 5 лет назад

My car acting weird now

@EvanGoyuk 5 лет назад

You didn’t use the correct PCV most likely

@JonathanGarcia-ec6uq Год назад

Vacuum build up when removing the oil filler is never good... you should not have that kind of Vacuum I noticed you might have put the little aftermarket pcv valve backwards which would probably be the cause of that vacuum build up. I installed a catch can on my 330i due to excessive vacuum build up now I can remove the oil filler cap with no issue car doesn't burn any oil at all

@bobafittness1346 4 года назад

Do you have a Facebook bro?

@EvanGoyuk 4 года назад

Instagram @evangoyuk

@eddiejohnson3366 Год назад

I’m gonna have to disagree with this whole catch-can install. I was almost all in with it and ready to tear out the OEM CCV system. But I started doing some research. What I learned was that the C/C (catch-can) system isn’t nearly as effective of doing what the stock CCV system is capable of. And for most of us who drive our cars as daily drivers it’s impractical. The C/C doesn’t effectively remove water vapor and ends up just recycling it back into the system. Another issue is there’s no science in your installation. BMW designed the engine to run at specific internal pressures and when you guys start reducing 7/8” lines and restricting then down to 3/8” that’s changing pressures dramatically. So basically what I’m saying is C/C have a place if done correctly with some proper engineering for racing where you are renewing the oil often. But for us who may run an autocross or track day occasionally the OEM system can’t be beat. I know it looks cool and all but…. I’ve omitted a lot so it doesn’t sound like a dissertation but you get the idea. And the catch-can system doesn’t look any easier to install as a new CCV system. Evan I have watched a lot of your videos and have got a lot out of them. You know a lot about these cars but I don’t agree with you on this.