BMW Headlights Condensation repair part1

Просмотров 706 тыс.

% 8 062

Hi, in this new episode you can see how I repair a headlight that take water and make condensation, on a BMW 5 Series F10, at first I thought it was cracked but it turned out that someone changed the lens and did not mount it correctly, I had to disassemble it again and do it properly, to open it I used the hot air blower set at 250 degrees Celsius and for reassembly I used a reusable mastic for which you can find the link below . Another adventure successfully completed !!!
For part 2 a more easy repair : ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE--ErJ6iC3Ip4.html
WARNING ! This is NOT a DIY , and I'm not responsible for any damage you may do trying to copy what you see in this Video.
I've been doing this for over 15 years, that's why some things may seem simple in this videos. I have a vast experience working with BMW MINI and Rolls Royce , abbreviated BMW Group , and that's why you may see things that seem impossible or very difficult to do, done easily !
I do NOT offer services! This channel is not an advertisement for a shop or something like that, it is for Educational and Entertainment Purposes, Thank You for Understanding !
If you want you want to support me :
PayPal : paypal.me/MunteanuO
Patreon : www.patreon.com/keddy_ovidiu?fan_landing=true
The white Grease that I'm using is "Molykote EM-60L"
Amazon Affiliate, Commissions Earned : if you buy from these links you'll make me rich :))
Reusable sealant : amzn.to/2JhtNVy
Main diagnosis HP tablet : amzn.to/372lmcq
HP rechargeable stylus for my main HP tablet : amzn.to/3NCh1xq
Multimeters and probes :
Probes KAIWEETS KET11 : amzn.to/3hoZVnO
Main multimeter KAIWEETS ST600Y : amzn.to/3M7lUO7
Second multimeter ZOYI ZT-X 9999 : amzn.to/3pnhNUq
Old multimeter UNI-T UT33A : amzn.to/3HpqGD1
Panel Clip Pliers for removing clips and harness :
amzn.to/32St4nC
Tesa Highest Quality Heat Proof Engine Compartment Wiring Tape :
amzn.to/3aoNHbE
Tesa adhesive wiring cloth tape : amzn.to/3gTycbZ
VIOFO A129 Pro Duo 4K Dual Dash Cam : amzn.to/3anGDMd
VIOFO Hardwire Kit for A129 : amzn.to/3x5F0wx
BMW e46 GM5 Relay : amzn.to/3d2qbTv
Ultrasonic bath (mine is painted black by me :) ) : amzn.to/3rU3tlj
Seat Thigh Support Actuator Repair Gear : amzn.to/35TSsXp
BMW f10 Leather door pull handle : amzn.to/3oLYIZV
FRM repair tool : amzn.to/3qKgr5o
DSO5102P USB Storage Oscilloscope 2 Channels 100MHz : amzn.to/3jPVAJd
3 in 1 Rework Solder Station : amzn.to/2F0BgWC
Flux Grease RMA223 : amzn.to/356CWcg
Chemtronics 60-1-5 SODER-WICK : amzn.to/2Z7iRP5
Chemtronics 80-3-10 Soder-Wick : amzn.to/3319i5i
Loctite #243 Threadlocker : amzn.to/356voG7
For filming /editing I'm using :
DJI OM 5 Gimbal Stabiliser : amzn.to/3Izu1DI
MY Camera Samsung s22 ultra : amzn.to/3ZlSKBE
Camera tripod : amzn.to/32SDRey
Microphone setup : amzn.to/3jS2uTL
Microphone lavalier : amzn.to/3iiXE1o
My work station MacBook Pro 13 2017 : amzn.to/3ckBIvx
!!! Ops it looks like you've reached the bottom !!!

Авто/Мото

Опубликовано:

26 дек 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 720

@tomytza123tomescu2 3 года назад

finally a romanian diy channel that make quality content

@MOvidiu 3 года назад

Nice !!

@michaelmaddox6646 Год назад

detailed, thorough, and to the point. This video should be used at all BMW training labs. well done, sir!!

@vfeinman Год назад

Second video I've watched of yours with the trusty knive you use. I'm in awe of your attention to detail and cleanliness. Thank you for posting!

@jegerm6752 Год назад

This is the video I was looking for! I shouldve watched part 1 before part 2 lol. I love how you opened the headlight using heat gun and pried it open. In other videos I saw on youtube, people just cut the headlight cover and fit new cover or just glued over the cut area, which scared me. I’m gonna show this video to the guy who’s going to repair my headlights. Thank you so much.

@stadug Год назад

If you are thinking of doing this yourself, there is something not mentioned here, the screw on the back of the headlight is very inaccessible, it gave me a lot of trouble like everything else I removed. Removing the plastic from the headlight is a separate story, after losing my temper with it I took it to the gentleman who does it to have it replaced. Thank you for everything else, very well explained!

@neaiskinksupratai8008 2 месяца назад

Now I'm stuck with those screws. Any suggestions?

@MrSbpool 11 месяцев назад

Thank you. This is a great video. The second screw behing was a nightmare with my limited tools. Thanks to your compressed air method I found a crack on top of the glass 😊. Fixed with a soldering iron. Pressure washed the car today and all good. No water 😊

@anc1741 3 года назад

What a great, well explained video. Thank you for taking the time to go into so much detail.

@MOvidiu 3 года назад

Glad you enjoyed it!

@Adrew133 7 месяцев назад

First one I've seen so far that properly (besides the knife action in the beginning) opens the cover without damaging, cutting, baking,, the headlight. This confirms that you can keep the OEM Hella headlight without going for expensive/cheap alternatives. Thank you sir for the REAL DIY FIX example 🙏

@MOvidiu 7 месяцев назад

Thank you for your feedback !

@JGV_IX 3 года назад

Though I love all BMWs, and yes even the controversial “Bangel” BMWs, the F10 5 series has a special place in my heart! I remember visiting the dealer just to sit in the driver’s seat...dreaming of one day driving a fantastic car like that! Thanks for the memories and the video 😏 Take care and keep well! Also as a side note...I miss my E46 where you could remove the headlight without touching the bumper 😂

@gtwhome 2 месяца назад

A fantastic guide - with some brilliant tips and pointers. Thankyou and bravo !

@dragosmarr7276 3 года назад

Lucrezi foarte bine! Detaliat și curat!bravo. Mi-as dori sa găsesc oameni ca tine sa lucreze asa si la a mea. Am un f10 . Un far începe sa se exfolieze si rămâne mat.se rup parca ar fi solzi de peste. Succes in continuare!

@valentinmindroc8889 3 года назад

Ovidiu, unde te gasesc? Imi place f mult ce faci si cum lucrezi. Esti genul de om de care toata lumea are nevoie. Bravo!!!

@jameswilliamson911 3 месяца назад

Thank you thank you thank you! Your air suspension video helped me a while back. This video (and part two) helped me find and fix a leak in my headlight. I got the common errors after I got really bad condensation in the head light. No cracks, but the seal on the outer side was bad. Dried out the light, check the module (luckily no corrosion and the connectors were clean), put it back on the car and no errors. Ended up resealing the area with clear silicone. Now let’s see what happens next time it rains 😅 Thanks again!

@Didyouseeitreally 7 месяцев назад

Excellent tutorial video. Just what I was looking for same headlight. Will attempt tomorrow.

@MPowerGPower 3 года назад

Very good video. And i understand your English perfectly. Keep up the good work!

@StasysFPV Год назад

Great video. I just had this problem, which was not cheap, but I didn't even think about doing it myself, because you need to have conditions. It is very strange that this is a big problem for BMW F series models.

@guillaumeerard 2 года назад

Very informative, thank you!

@alltheway99 Год назад

Thanks Ovidiu, Nicely presented 🙂

@khyzer4029 Год назад

Brilliant way to explain in details.

@headlightdesigngradacac 3 года назад

Awesome video... The way you check where is leaking is something new i learned. Greetings from Bosnia

@MOvidiu 3 года назад

Glad it was helpful! :)

@IrishScott71 3 года назад

I enjoyed your very good attention to detail and perfection with your work! I can only imagine the cost of the actual headlamp housing vs the time you took to do this repair.

@MOvidiu 3 года назад

Glad you enjoied !!

@joemayo3650 2 года назад

I need have mine done and bmew want £1250 for parts labour and tax

@danielhu8305 2 года назад

I need to have mine too, daylight + blinkers don't work anymore due to the condense... it will be a 3k fix...

@Vince-VA 2 года назад

Very time consuming, I enjoyed it

@damianspencer9057 2 года назад

@@MOvidiu how much do you charge

@derekstocker6661 5 месяцев назад

Thanks for this. When we see how many views these lamp condensation video's have is it not time the manufacturers did something positive to stop the problem! I have had this twice on a BMW E36 but cannot find a video showing how to cure apart from putting a hair dryer over the glass, and lasted for a few days. I then had the headlamp replaced and same thing happened. Now just hoping for sunny days to hopefully cure the problem until next winter!

@julianappelt3516 3 года назад

And finally i seal my headlight in 5 minutes with silikon ... its dry since 50 tkm ... but finally nice professional work bro! Everything is perfekt!

@MOvidiu 3 года назад

I'm glad you enjoyed !

@jerryliu8970 3 года назад

great job. i hope I can find someone who can take care of my care as much as you do.

@MOvidiu 3 года назад

You will definitely find it , it will cost more than someone normal . but you will find

@kaviator Год назад

Thank you very much @MOvidiu, this was truly an excellent video, very detailed and thorough. Watching this video, I figured there are really two sets of skills at work. The first (and easy) set of skills was just the removal of the bumper and the headlight assembly. The second (and difficult) set of skills was the disassembly of the headlight unit and the resealing of it. Your video taught me to do the first, but to skip the second and take the headlight to a specialized shop to be resealed by a professional who has plenty of experience in this specific task (in my case, it was Headlight Factory in Sun Valley, CA, near Los Angeles). There are 2 minor areas that could be improved in your video: 1- You mentioned 2 plastic clips at the bottom of the bumper at 5:15. I could indeed remove them, but could not put them back for the life of me, there was just no room to push them down. Any tips on how to do this would be appreciated. 2- You did a really good job telling what screw was what size and you showed where it was except for 2 of them at 6:08 and 6:23, I assume it was a difficult angle for the camera and the light. All in all, you did a phenomenal job!

@AleksandarLukic-uq5ln 4 месяца назад

😮

@gutnick 3 года назад

Great work. Impressive attention to detail

@MOvidiu 3 года назад

Hey , glad you like it !

@Kuma_Cordova 3 года назад

Amazing work! Thanks for sharing.

@MOvidiu 3 года назад

I'm glad it was helpful and thank you for the feadback !

@Alin_KIR 3 года назад

Foarte frumos lucrat! Felicitari! 👏

@martinbur200 Год назад

Thank you so much. U saved me 2000€ with this tutorial. God bless u :)

@michals8351 3 года назад

Another perfect video 👏👏👏 Thank you for your hard work, bro 👍

@MOvidiu 3 года назад

Hey there! I'm glad that you like it

@giorgitsalatze1370 3 года назад

@@MOvidiu hello bro thnks for this video where i find this silikon

@MOvidiu 3 года назад

@@giorgitsalatze1370 Read the video description:)

@FamilyBusinessZone-hh1pp 2 месяца назад

Thanks for this video. Very helpful. In my case, I realised I didn't want to take this on myself! For those in the UK, Home of Headlights in London reseal headlights at a very reasonable price. I'm a happy customer, having a BMW 5 Series F10 left hand side headlight resealed.

@paulbear. 2 года назад

Perfect job. Thank you

@MaximeSourbeer 3 года назад

Impressive work, thanks for the upload

@MOvidiu 3 года назад

Glad that you like it, check out the rest of my videos!

@russellwilliams5336 Год назад

Ok, so this weekend I finally took the nearside headlight out - in the rain! I was able to drain out about half a mug of water through the vent on the far corner, so it had gone way beyond 'condensation' stage!! I used soapy goodness as described and used a pump up water sprayer (empty of course) and only saw massive bubbles coming from the two caps - lots of bubbles. Nowhere else though. Having popped it in the oven for about an hour on 50 degrees fan and hiar-dryered it, the following morning it was dry, but the little control board was clearly being submerged because, even gentle acceleration was triggering many faults with their associated bings and bongs warnings, including no left indicator. So I used some double sided sticky tape to bulk-up the seals and then they were hard to put back on - excellent. I have just reassembled it all after drying the little control module and cleaning the terminals/contacts and the whole thing works beautifully. I did this on my narrow driveway exposed to the elements. I feel I need a week off, counselling and a pay rise. Fortunately, I only have one bolt left over and I have absolutely no clue where i removed it from. Thank you for your guidance - particularly regarding that bolt right up behind the rear inner aspect of the headlight. That was clearly positioned there just so someone could design a new special tool to get to it. Pure evil BMW, pure evil...

@bogdanb6415 3 года назад

This is great mate, thanks so much I will do mine tomorrow just before setting to work

@MOvidiu 3 года назад

Have fun :)

@cino4919 3 года назад

Clean job!

@nicolaepetrescu601 2 года назад

Super tare! Felicitări!

@REALLYRANDOMREVIEW5 2 года назад

Good Job i have this problem with a BMW 1 series and This is the Best Demo of tear down and Repair Thanks !

@MOvidiu 2 года назад

Glad it helped

@MartinMaat Год назад

Thank you, this cleared up a lot for me. I am struggling with the same issue (I have an F11, practically the same head light). I didn't mind the wetness that much until failure messages started to popup, later followed by actual failures of direction lights along with just strange behavior. Both the local repair shop and an official BMW dealer only offered a replacement, no repair, claiming it was impossible to take it apart. Anyway, the offered replacement was way too expensive to take lying down (over 1500 Euros) so I started tinkering. I first tried to dry the thing by putting a hair dryer in the circular hole after screwing off that cap. Put the engine on, big lights on, warming the thing up real good and it visibly dried up in an hour or so. I then stuffed a bag of silica gel into the hole and screwed the cap back on. This operation actually made the problems go away for a couple of weeks but of course that didn't last. I never really replaced the wet air. It looked like some of it escaped when heating it up but most of it remained trapped and was just distributed internally, temporarily drying up the affected electronics. I am not enough of a mechanic to take the bumper off so today I drilled some holes into the transparent part just under the hood and pumped in dry air to replace the wet air. That worked a bit. Once dry I intend to plug the holes again with sealant, hoping it will be OK for a couple of months. I will probably have to repeat this process in the future to keep it in working order. And nuke the silica gel in time before it gets saturated.

@jpctc2008 Год назад

i have same problem now, did this work?

@MartinMaat Год назад

@@jpctc2008 The silica gel was not that effective after all. Just taking the screw cap off and leaving it off worked better, I haven't had any condensation in the lens since I did that. After a short lived recovery the problem remained stable: no direction light from the unit (the direction light on the side panel still works). It has been like this for months now, all winter. During really wet periods I still get the odd problem with the right direction light not working either but this typically clears up quickly. I can live with it but my car is up for periodic inspection (mandatory where I live) and probably won't be approved with this issue. So I will have to have it fixed after all. I did learn the problem is in the electronics. That could be a cheaper fix than replacing the whole unit. Back to the dealership...

@jpctc2008 Год назад

@@MartinMaat i live in Netherlands, its cost about 1300-1500 euro by bmw-dealer, i think it's not necessary to replace it for such price. i dont worry about the fog, but the rust/corrosion with too many water in the cap. i will open the cap, try some silicagel after this. thank you

@MartinMaat Год назад

Here's an update. I found and ordered the TMS module online and replaced it (Googled for serial and part number which are printed on the circuit board). It is accessible though the hatch in the front wheel cabinet. The original module was corroded at the contacts. The replacement worked a little better, it fixed the turning light but not the angel eyes. I read on the internet that the module might need to be "coded". I found a shop that could do this but it made no difference. A couple of days later, after some rainy days, all of the problems returned. The TMS module compartment appeared to be all wet. I dried it with paper towels and then everything worked again! Then I dried it some more with a hair drier and it stopped working again. It turned out the connector slot the TMS module is seated in was badly corroded. The outer contacts were all gone and others were half gone. I could see this after taking a picture with my phone with flash. With too much water I got short circuits, with it being dry there was no contact. I looked like I hit the sweet spot for a moment but obviously this was not going to become better. It looks like I need a new unit after all. The connector does not look replacable.

@FrodoBeutlin1984 2 года назад

Guy you are very skilled! Thx for your tips!

@MOvidiu 2 года назад

Glad you like them!

@nigelbarratt6825 6 месяцев назад

My mate has a 2012 reg 530D which he's had from new, always BMW main dealer maintained. The left hand (HiD) headlamp was misting up to the extent that it was throwing up faults on the computer due to the damp in there. BMW quoted £2,300 for a new headlamp and fitting. We hinged up the plastic cover under the bonnet and removed the bayonet-fitting circular cover in the top of the headlamp, which now lives in the driver's door pocket. with the top of the headlamp open. We then dried it out gently with a hot air gun and put a couple of silica gel bags in from the top. The cover was left off, and since then it's been through a winter and a summer with no trace of internal condensation. (It is always condensation by the way, not water ingress). No problems at all. I also recommended this to another friend who had the same problem with the same model and he's had clear lamps ever since as well after doing the same thing. Much better than all this faff!

@dgoettel13 3 месяца назад

I sealed the wheel well panel that gave access to the back of the headlight after I put gasket silicon on the round seals. When driving in the rain, water should not come through the plastic cover. The air escaping would allow water in if the headlight was under water but not from just rain. A crack maybe. Sealing the wheel well access panel helped and I have not had issues since. Bad design. In heavy rain the wheel well is splashed constantly from the tire carrying water up.

@nigelbarratt6825 3 месяца назад

You're assuming that the moisture in there is water ingress due to water leaking into the light. There was no water ingress, in these two cases at least, it was just condensation forming within the light. In the second case the owner removed the light and proved that there was no water getting in and that the misting was just condensation, so there was no point in trying to seal leaks when there weren't any.@@dgoettel13

@EddyKuul 2 года назад

Great video. I wish someone like You could fix my car. Thanks

@m4nu98garage 3 года назад

Nice work, 👌🏼 greetings from a BMW Driver to, from Germany ✌🏻

@MOvidiu 3 года назад

Hello there! :)

@bolniqtmozuk9159 Год назад

Great work! With that video you helped to many peoples! Thank you

@MOvidiu Год назад

Glad to hear that!

@vichenderikx8365 Год назад

Perfectly done!

@goldshakal5600 Год назад

Thank you for this Video, really good Job 👍

@paskepaske6250 2 года назад

Nice and clear video M. Ovidiu. Next week i will give it a try. Just some questions: what is the diameter of the silicone seal u used? And you prefere a silicone seal or butyl?

@allmech_BMW_fault_finding 3 года назад

Great video pal! Looking forward to watching more of your content.

@MOvidiu 3 года назад

More to come!

@dainizz3330 Год назад

Nice, good job! Loved your video.

@miodragpetrovic7915 7 месяцев назад

Great tutorial! Much appreciated!

@seanjefferyrobinson 3 месяца назад

Amazing job and so patient with it. I wish you could do mine!

@willyemongo5179 3 года назад

Amazing job !!!!!!!

@andrear1727 Год назад

Finalmente un video che mostra quanto realmente è difficile aprire un fanale!

@cliffjohnson7298 2 года назад

A job well done!

@martymeyer4125 3 года назад

Did a replacement lens on an X5. Make sure you use compressed air to blow out all the accumulated dust particles before reassembly. You can use 3M windshield adhesive in the channel, for the reinstall. I needed to sharpen a screwdriver to dig out the old adhesive.

@erfan6269 2 года назад

Hello Marty. I am looking for someone to do my BMW 5 Series headlight. Would you be interested ? Where you based ?

@martymeyer4125 2 года назад

@@erfan6269 I'm in NC. I would advise doing both, so they match. Not sure I would want to do it for someone else. There is a risk involved in screwing up. The lenses I put in a year ago already need to be polished. Plus it takes about 5+ hours per light. So I'd have to charge $150 per light, plus the cost of the lens. Cheaper than new, but not cheap.

@erfan6269 2 года назад

@@martymeyer4125 Hey Marty thanks for replying. I am in Manchester, England, so North Carolina going to be a bit too far 😉.

@silvialake5829 2 года назад

So clean! I want to do this to my BMW - it's a family car. It was my Grandmother's, then she gave it to her daughter, and then my mom gave it to me. All I need is a garage and cool tools.

@MOvidiu 2 года назад

Nice to hear that! Go for it, but be aware that it is a little bit hard !

@ernestbilesjr8818 2 года назад

What a great video.

@bmw_f11-simple.repairs73 2 года назад

Auto Po zalaniu.zadanie wykonane na 10.bardzo dobra Robota 👍👍👍

@valefur72 Год назад

I have had a big problem with the rear screw of the left headlamp on my 2014 520d b47: there is an electric water pump in that place and removing the screw is almost impossible. I have broken away the light (it was already broken doing to a deer collision). When I have mounted the new light, I've simple swapped the clip with the screw, to put the screw from the front of the headlight. The right light had a problem of moisure and I have sealed the light all around with a special silicone . Thank you for the video!!!

@user-pr8fr1ls2m Год назад

Excellent instructive video thank you. It helped me fix a leak I had in the passenger headlight a couple of years back - thank you. When the drivers side showed heavy condensation recently I tackled the job with a little more confidence but on removing the unit, I cannot find the leak anywhere! I have sprayed soapy water and puffed air for ages. I'm stumped. Reluctant to put it all back together without diagnosing the problem. Any suggestions? Please?

@rainerzufall9480 10 месяцев назад

Great work!

@MinhNguyen-yk5mx 3 года назад

Good job, your work place nice and clean

@MOvidiu 3 года назад

Thanks 😊

@user-vs5lo4ej3k 8 месяцев назад

Super schön gemacht!!! Super!!! Super 😮❤

@Viktor-lv1ro 2 года назад

Klasse Video. Thank you.

@olivman4795 5 месяцев назад

Very good job and well explained, well done man

@MOvidiu 5 месяцев назад

Much appreciated!

@lucianrata280 3 года назад

BRAVO ! Super canal, te încurajez sa continui. Imi permit si o remarca constructiva consider eu. Lucreaza un pic la dictie în Engleza. In rest te felicit, tine-o tot asa ! :)

@zenerii 3 года назад

We just inspected the same thing on my E65. In my case it was low beam bulb cover😀👍

@fixitwithjake 3 года назад

How did you seal the bulb cover better? Mine is leaking badly too!

@ricardobrown1940 Год назад

I like the instrumental in the back ground playing

@syedaurazee 2 года назад

Great video. How did you deal the headlight again using only pliers? Do you have to heat up the sealant first?

@AleksandarLukic-uq5ln 4 месяца назад

Dobar klip...pozdrav iz Srbije

@southbrit 3 месяца назад

Love this and I am doing just this on the facelifted version. Seems to me though that BMW have made it harder as the lens is now attached to the housing with a screw that is impossible to reach.

@zeothorn 2 года назад

Great video and the job well done!

@MOvidiu 2 года назад

Glad you enjoyed it!

@user-cg9nm5zk5v Год назад

Very good I will be giving my garage a bell thanks😅

@gari4kata 3 года назад

Parts OEM de cinta headband black Nice 👍

@jmerodgers 3 года назад

Really thorough work. Great video work too! Subbed

@MOvidiu 3 года назад

Awesome, thank you!

@ZA-du3dm 2 года назад

Very helpfull video , you are true profesional , thank you

@MOvidiu 2 года назад

Nice! Thanks for appreciation

@taha200795 3 года назад

“Was smart enough to do this iob but not smart enough to do it properly” 🤣 so true

@mikewilliams4947 3 года назад

But it got done without damage :) Success! Five more times and you'll have it down:)

@nilowilliams6981 Год назад

Great video. What's the approximate cost for fixing a leaky headlite?

@ooorobbo Год назад

Good effort doing the whole video in English, well done mate 👏🏼

@markfitzgerald7556 3 года назад

Thanks for the video, next time make an oven out of a cardboard box to heat up the headlight adhesive fully using your heat gun, that way you can do the job of removing the lens easier. Then i would use a product called Selleys D Mastic specially designed for headlights and windscreens etc.

@casst346 2 года назад

nice quality work!

@MOvidiu 2 года назад

Glad you like it!

@markalcomdmarcos7132 5 месяцев назад

Nicely done 👍

@fixitwithjake 3 года назад

Really nice video dude! I removed my light and could only find a leak on the two caps to the bulbs. But, yet I have a ton of water in the housing. 1. Does that sound right? 2. What grease should I use to better seal the lens caps? Thanks for the great video!!!! You helped me out a ton!

@MOvidiu 3 года назад

Glad I could help , use normal grease you just need to lightly grease the gaskets to slide in place

@nachnamevorname5917 2 года назад

Very good work! With love 😁😊👍🏻

@MOvidiu 2 года назад

Thanks for appreciation !!

@DG-od4si 3 года назад

nice video, thanks

@hannibalmugen 3 года назад

Nice video. Well done !!

@MOvidiu 3 года назад

Thank you very much!

@cristimarcea 3 года назад

Multumim pentru munca depusa, sa ne prezinti intreaga operatiune!. Cum se numeste banda aceea de lipit? E speciala pentru lipit sticla de faruri sau e pentru parbrize? Mult succes in continuare!!

@Kietux1 3 года назад

Nice work !

@MOvidiu 3 года назад

Thank you! Cheers!

@rileymakay2024 3 года назад

Great video - thanks for sharing

@MOvidiu 3 года назад

Glad you enjoyed, and thanks for feedback

@michalkowice1989 3 года назад

Clean work nice done 👌

@MOvidiu 3 года назад

Thank you! Cheers!

@ndumbadavid20 3 года назад

Thank you very, this is an amazing video 👏👏👏

@MOvidiu 3 года назад

Glad you liked it!

@tumke86 Год назад

thanks, i'm going to do it this way too! Can I also use glue or sealant kit ?

@tonyhughes7792 Год назад

Thank you, that`s really well done of you. I`m saving this video. I have seen people get units apart by warming a whole assembly in a cooking type oven, have you tried to use this method for a stripdown? I`m interested in getting both mine apart, Mazda, as i have dust inside on my lenses.

@endurozone3825 3 года назад

Nice and clean job Bro

@MOvidiu 3 года назад

Thanks 👍

@avp8430 2 года назад

Mișto, mulțumim pentru video, foarte util. Mi-am reparat un far de Hyundai urmărind asta. Inițial am lăsat masticul vechi (am urmărit alt clip) și i-am turnat niște silicon negru de jur împrejur. Dar, aparent, nu s-a sigilat suficient de bine. La prima spălare cu jet a intrat puțină apă printr-un colț. Am luat mastic nou, demontat, curățat iar de mi-au venit dracii, pus mastic, încălzit, împins bine componentele, testat apoi cu săpun și pare să nu răsufle pe nicăieri.

@MOvidiu 2 года назад

Super tare ! ma bucur ca ai reusit ! Bravo!!

@moholdt3335 2 года назад

Happy smile in end very nice!

@MOvidiu 2 года назад

Awesome !

@esergeckalan8163 3 года назад

Perfect jop thanx for video this video has been a guide for me and i done it whit a friend

@MOvidiu 3 года назад

Glad it helped

@SoloSurvior 3 года назад

Going to attempt this on my f20 wish me luck !

@SoloSurvior 7 месяцев назад

*update* didnt work for me, i took out the headlight and noticed a very big crack so just bogutht another one - luckily i only had halogen back then so wasnt too expensive, i now own a different model with adaptative LED headlights :o