Тёмный

BMW S63/N63 Must do DIY - Oil Pump Chain | 4K 

E70M Garage
Подписаться 1,2 тыс.
Просмотров 5 тыс.
50% 1

Parts Needed:
(1) Lower Pan Gasket # 11137566808 ]www.fcpeuro.com/products/bmw-...
(25) Oil Pan Bolts # 07129909333 www.fcpeuro.com/products/bmw-...
(6) Reinforcement plate bolts(Do not reuse, these are one time use only) #33306772888 www.fcpeuro.com/products/bmw-...
Gasket Tack:
www.amazon.com/Permatex-80064...
Tools Needed
Torque Wrench
Torque Wrench Angle Gauge
Cordless Ratchet (highly recommended, 31 bolts to remove and reinstall)
3/8" extensions
8mm long reach hex socket
T45 Torx socket
E10 External Torx socket
16mm Socket

Авто/Мото

Опубликовано:

 

13 июл 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 25   
@lochlanmckenzie8992
@lochlanmckenzie8992 7 месяцев назад
Nice job mate! great tutorial. it's about time you get those Rod bearings replaced. Unfortunately my e71 X6M decided to spin a bearing at 168,000kms so I highly recommend doing it. haha
@djlazarek5830
@djlazarek5830 10 месяцев назад
Those are some bad ass wheels
@timcallahan1055
@timcallahan1055 8 месяцев назад
Nicely done! I just picked up a 2018 F85 w/37k miles. I will keep this in mind for the future.
@E70MGarage
@E70MGarage 7 месяцев назад
Thanks, and congratulations!
@user-di4px5qg4h
@user-di4px5qg4h 4 месяца назад
very helpful thank you
@Dat550go
@Dat550go Месяц назад
Dont do this! Its a joke. Or lie. Misleading. Should be banned.
@Nohchi777
@Nohchi777 10 месяцев назад
Hi, how 0-100 time?
@farturinn
@farturinn 4 месяца назад
I have re-used my reinforcement plate bolts multiple times, probably not a good idea :D
@E70MGarage
@E70MGarage 4 месяца назад
I have too 😂 but it's not a good idea. Bolts that have tightening torque and degrees specs are stretched or de-shaped - may appear to be the same to naked eye, but aren't.
@Dat550go
@Dat550go Месяц назад
This is inaccurate and misleading information and should be banned.
@sickvick83
@sickvick83 10 дней назад
24nm is way to high for torquing a oil pan bolt you mean 12nm
@Driven_Life
@Driven_Life 2 месяца назад
For the n63tu do you know the torque specs for the rod bolts
@Dat550go
@Dat550go Месяц назад
This video is misleading and should be banned.
@SageXteriorCleaning
@SageXteriorCleaning 11 месяцев назад
About to do this on my 2014 550i. Did you end up buying new reinforcement plate bolts? Since they’re one then use. Also, how are you able to measure how many mm of slack you have.
@E70MGarage
@E70MGarage 11 месяцев назад
I didn't replace the reinforcement plate bolts, but you're correct - they're one-time use only. I eyeballed it, 6-12mm is about 0.2-0.4" but you can find specialty tools to measure the slack from eBay.
@karannanda6517
@karannanda6517 11 месяцев назад
Have u ever timed ur 0-60? How much whp?
@SageXteriorCleaning
@SageXteriorCleaning 11 месяцев назад
@@karannanda6517 it’s supposed to be 4.5 seconds
@karannanda6517
@karannanda6517 11 месяцев назад
@@SageXteriorCleaning "supposed to be" he's stage2+
@philliesclips7348
@philliesclips7348 10 месяцев назад
Do you have a transmission tune?
@E70MGarage
@E70MGarage 10 месяцев назад
Nope, not yet!
@MVaccaTTACK
@MVaccaTTACK 11 месяцев назад
Any symptoms or noise that made you aware of this
@E70MGarage
@E70MGarage 11 месяцев назад
There was a chatter/rattle for 10 seconds or so at cold start, it's still there but fairly less.
@Dat550go
@Dat550go Месяц назад
​@@E70MGaragethose sounds are actually from the 4 throttle bodies. Each cylinder has one. Sounds like a type writer.
@Dat550go
@Dat550go Месяц назад
Did you change your chain and chain guides? That is the only way to truly solve this issue.
@RubenLindgren
@RubenLindgren 11 месяцев назад
'Promosm' 😔
Далее
The Worst BMW Ever?
11:32
Просмотров 748 тыс.
Чистая Правда о BMW S63B44 X5M X6M
37:50
Суши из арбуза?!
00:34
Просмотров 146 тыс.
How to SET TIMING - BMW N63 and S63
11:23
Просмотров 1 тыс.
BMW S63 Engine | Common Problems & Reliability
12:19
Просмотров 13 тыс.
Почему шины стали черным🤔
0:35