Brake Lathe Arbor Maintenance

Подписаться 8 тыс.

Просмотров 9 тыс.

50% 1

Sign up for the Raybestos Brake STOP to access premium training videos from Raybestos: bit.ly/2TBs1hx
If you machine rotors with a brake lathe, it is vital that you keep the machine well maintained. With today's tight rotor and drum runout specifications, you must make sure that your lathe isn't contributing to excessive runout. In this video series, we will walk you through some steps you can take to ensure your brake lathe is operating correctly. This will help ensure a quality brake job.
Visit our Website: www.raybestos.com
Like us on Facebook: / raybestosbrandbrakes
Follow us on Twitter: / raybestosbrakes
Follow us on Instagram: / raybestos_brand
Follow us on LinkedIn: / raybestos-brakes
The first part of the brake lathe that we are going to discuss is the arbor. It is important to make sure that the arbor itself does not have an excessive lateral runout.
The AMMCO brake lathe that we are working on calls for a runout of one thousandths or less. When we tested the lateral runout of the arbor, we found it to be excessive (over 10 thousandths).
What do we do in this situation? We must remove the arbor itself and inspect it. Removing the arbor is as simple as loosening the nut at the end of the lathe and removing the bolt. This will allow you to pull the arbor shaft out of its housing.
Once you have the arbor shaft out, it is important to inspect it for any nicks. Clean the shaft with sandpaper to remove any shavings or debris on it.
Additionally, clean the arbor housing with sandpaper. An easy way to do this is to turn on the lathe and press the sandpaper against the housing.
After cleaning the arbor shaft and the housing, make sure to align the witness mark on the arbor with the witness mark on the lathe spindle.
Once you re-install the arbor shaft, check the lateral runout again. If the runout is still excessive, disassemble the arbor shaft, rotate it 180 degrees and re-install the shaft. If the runout is still excessive, you will have to replace the arbor shaft.

Авто/Мото

Опубликовано:

27 янв 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 10

@burkestrand5070 11 дней назад

I love this guy!! He is awesome!!!! Need more videos like this, he's a great teacher and your content is way better articulated than anyone else!

@JAlonge017 Год назад

amazing content, thank you man, i just wish people who needed to see/ hear this would actually watch it instead of automatically thinking they already know best.

@davidikyo2482 Год назад

My arbor wobbles whenever I machine rotors. The lathe is on a perfect ground and I use appropriate type of cone, yet it wobbles. What could be the problem?

@sinned96 4 года назад

Runout is checked near the threads not in the middle. It doesn't bend in the middle. It will bend at the arbor face

@alarconisco116 2 года назад

King pin removal tool for trucks

@peanutbutterisfu Год назад

The measurement should be taken near the threads, the further you get away from the taper on the arbor the higher the runout will be.

@Go69 Год назад

Anyone have any ideas how to fix runout on an accu turn lathe? Mine is doing CRAP work on rotors at the moment. If I can't fix it, I have to trash it as it is unreliable atm.

@peanutbutterisfu Год назад

Never taken an accu turn apart but if you can take it apart like this and clean it I would try that. If u put it back together and it has a small bit of run out use ur dial indicator to find the high spot and then use a heavy brass hammer to hit the high spot then re check until it has less the one thousandth run out. If it has a lot of run out and the arbor is like this one where it’s tapered put valve lapping compound on the tapered area, turn machine on and put arbor in to lap it for like 45 seconds, turn machine off, clean compound out of lathe and shaft and if the area looks good install the shaft and see what you got, if it’s still really bad u might need a new arbor as long as you don’t have bad bearings or something causing that.

@Go69 Год назад

@@peanutbutterisfu I have tried the lapping compound method and it did not help. I believe it's going to be a bearing issue. The reason I think it is the bearings is because with my dial indicator on the arbor (regardless of clocking of arbor) I can lightly push up or down on the end of the arbor and the dial indicator goes crazy. I know that I have a lot of leverage out on the end of the arbor but very light finger pressure should not allow, or be causing, such massive swings on the dial indicator. I can push up, or down, with minimal pressure and the indicator is changing as much as .020"... I don't think that is normal. For as thick as the arbor shaft is I can't imagine that light finger pressure could bend it enough to allow that much deflection. Do you have any idea how difficult it is to change the bearings on one of these? I've been looking on-line and cannot find a diagram on how to disassemble or service it. Last year the electric motor went out and the company I called charged me $1200 to replace just the electric engine. I honestly did not ever imagine it would be that much so I did not ask for a quote up front. Needless to say I won't be calling them for ANYTHING going forward and will either have to fix this myself, or scrap the machine.

@sinned96 4 года назад

Not all arbors or lathes have the witness marks.