Braze A Gas Vs Mapp Gas Video 

Usually the music is annoying but you made a good choice. And, as a newb, I appreciate the brazing demonstration. Thanks!

For one off brazing jobs, like repairing a pipe i like my mapp torch, i have three different ones, i use a double burner one on bigger pipes. But for install, bigger pipes or component replacement such as driers, tev's, compressors etc you need an oxy fuel torch. Its not just the time to do the braze, but the time to carry the brazing torch from the van to where you are working that is a factor.

I tried once brazing with maap gas on a 7/8 elbow fitting. I was up on a ladder about 20ft and shit let me tell you... I would not do it again. I gave up on the MAAP and went back down to get the B-Acytelyne tank. I had to rope it off the side of my ladder but it was just alot quicker. That flame on Braze-A-Gas sames really long. I wouldn't recommend using it in tight corners, especially if its a clients house. Learned that mistake :P

Does braze using mapp gas leave dust after inside the copper?

Did you think people would like the music?

The elbow is faster than the union to braze because the elbow dissapates heat slower, show comparison brazing same fittings

It should be used the same kind of torch to compare.

That music is horrible, lol. Does the pipe really need to get glowing red hot melt the solder?

Not a damn thing was done wrong here. The puddle was "properly laid", the "silicon bronze 15% silver" brazing stick achieved a nice "plastic state", and flowed 'into, and onto' the joint , about as nice as I've ever seen - without going the "acetylene route". This work, without question, would easily stand up to the 750 psi required for a great deal of the refrigeration work done these days. About the nitrogen,,,,,,,,

Cook it! Cook it good! 🔥🌡👎

mapp or map pro? and what is ''braze-a-gas''? No reference to it anywhere (google) other than this video and a site that sells refrigerant equipment -but makes no reference to this torch or gas -or whatever it is.

You're bringing the torch too close to the fitting. The hottest part of the flame is just above the cone!

Maybe next time use the same torch for both gases, otherwise this comparison is entirely meaningless.

of course it takes less time, you're using oxy-fuel!

Of course oxy/acetylene is gonna be faster...mapp is good for small repairs and a lot less weight to carry around.

You don't know how to sweat you bunned the fitting up making it weaker

My choice is the cheapest! Someone else is paying for the time! 😜

Πολύ καλό το φλογιστρο το mapp pro gas turbotorch κάποια στιγμή θα αγοράσω και εγώ τετιο φλογιστρο είναι καλό για δουλειές .

That's a real bad braze joint, with oxy acetylene it looks like wayy too much heat & all the braze flowed out, on the oxy acetylene you gotta learn how to control the heat man, a little practice & you'll get it man,that flame is wayy too big for that 5/8" pipe it looks like. With the mapp gas it looks like you did a good job, that's pretty much as good as it's going to get with mapp gas as the temperature of mapp gas is pretty low especially for brazing, for soldering mapp gas is good enough for sure

That pipe is way way way overheated. Terrible job

no need flux for silver brazing copper to copper!!!!!!

Get rid of that music.

Whats the song?

Cooked

I’m no professional but watched my plumber do this under our sink and I have to say, whoever you’re guy is doing this, is terrible at it. If he’s not professional then he shouldn’t be doing a comparison video.

WTF is A gas?

My choice is not to listen to that "music"

τιμή μου οκ.

Music is horrible and not needed or wanted

But takes twice the time and skill set lolol turn it in climate center your kidding no one lolol

What’s up with that irritating, stupid music

Kaput 😂😂