Grapefruit Gose Recipe:
rb.gy/gaxtmt
HLT:
Ss Brewtech 37L / 10gal Kettle ( Original Version out of production)
rb.gy/rcmf4p
Spike Brewing 10gal Steam Condenser Lid
rb.gy/getjad
Changed out spikes condenser for one i already had
Craft Hardware Steam Condenser
rb.gy/o0kbar
Ss Brewtech 2.25” Sight Glass
rb.gy/909o6f
The base of the condenser is attached to the kettles handle with an early version of Craft Hardwares kettle Lid Hinge.
Craft Hardware Kettle Lid Hinge
rb.gy/gfvpkf
Generic 3” - 1.5” Sanitary Bowl Reducer
rb.gy/v8hzwi
Brew Hardware Spincycle Weldless Kettle Whirlpool Return
rb.gy/zmn80t
Brewtools TC34mm Weldless Fitting
rb.gy/cgn8ln
Brewtools Dip tube, short Without O-rings
rb.gy/l45dnj
Brewtools 34mm TC Ball Valve, Straight
rb.gy/qfp8hy
Caso Pro 3500 Mobile Induction Hob
rb.gy/v1b915
The hose from the HLT to the B80 has 2 barbed fittings and was cut to size.
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Brewtools TC34mm to 19mm hose barb (X 2)
rb.gy/ufibkp
This leads into the right sparge / pump port of the Brewtools System.
Brewtools B80pro Brewing System
rb.gy/toqaej
Brewtools B80pro Starter pack, 4-valve setup
rb.gy/ebdhgj
Brewtools B80pro 34mm Right Pump / Sparging Port Set-Up:
Brewtools 34mm Dip tube, Adjustable
rb.gy/s1z16t
Brewtools TC 90 Degree Elbow
rb.gy/4pkesq
Brewtools 3-Way TC Ball Valve
rb.gy/sctsa9
Brewtools 34mm TC Tee, L=60mm
rb.gy/aeeax7
Brewtools TC34mm Pull-type PRV
rb.gy/0nqcyk
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Brewtools TC34mm to 19mm hose barb
rb.gy/ufibkp
Brewtools Inline Temp-sensor with adapter
rb.gy/mxkksm
Brewtools 34mm TC to 1/2” F-BSP/R w/Gasket groove
rb.gy/bs90db
Brewtools Gaskets for Pump Fittings
rb.gy/nuj7wv
Lower Left Pump Output Port:
Brewtools 34mm Classic Sight Glass
rb.gy/v1dlxu
Brewtools 3-Way TC Ball Valve (X2)
rb.gy/sctsa9
Brewtools 34mm Modern Sight Glass (X2)
rb.gy/sfbudr
Brewtools TC 90 Degree Elbow (X2)
rb.gy/4pkesq
Brewtools TC34mm to 19mm hose barb (X2)
rb.gy/ufibkp
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Upper Left 34mm System Port:
Brewtools 3-Way TC Ball Valve (X2)
rb.gy/sctsa9
Brewtools Inline Temp-sensor with adapter
rb.gy/mxkksm
Brewtools TC34mm to 19mm hose barb (X2)
rb.gy/ufibkp
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Chiller Set-up:
Brewtools 34mm TC Counter Flow Cooler Pro
rb.gy/snj62m
Brewtools TC 90 Degree Elbow (X2)
rb.gy/4pkesq
Brewtools TC34mm to 19mm hose barb (X3)
rb.gy/ufibkp
Brewtools 34mm TC Garden Hose Adapter
rb.gy/eysmum
Transferring to Fermenter / Filling System with water
Brewtools TC 90 Degree Elbow
rb.gy/4pkesq
Brewtools 34mm TC Garden Hose Adapter
rb.gy/eysmum
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Brewtools TC34mm to 19mm hose barb (X2)
rb.gy/ufibkp
I relocated the Brewtools Systems control box using the available cable extensions and Control Box Bracket.
Brewtools Cable Extension Kit, 2.5m
rb.gy/e15ks2
Brewtools Bracket for Control Box
rb.gy/lxkdj9
The Malt Basket has been upgraded with the Brewtools Laser Cut Filter. The basket has also had the alternate, extra large, malt pipe latches added.
Brewtools Laser Cut Filter
rb.gy/c4p1sb
Brewtools Malt pipe latches, XL
rb.gy/xbwgsy
Brewtools Mash Temp Sensor 500mm
rb.gy/7wmhcs
Boiling:
Brewtools Steam Hat B80pro with Silicone Plug and Seal
rb.gy/rd9vrx
Brewtools Steam Condenser
rb.gy/czc7qx
Attached to the 34mm fitting on top of the condenser is a metal coffee machine hose i found at a local hardware store. i added a 34mm threaded TC fitting to the elbow of the hose to make it easy to remove when i need to remove the steam hat. The other end of the hose goes into the water splitter below the brewing table.
PEX Flexible Metal Hose
rb.gy/a4gi1f
Brewtools 34mm TC to 1/2” F-BSP/R w/Gasket groove
rb.gy/bs90db
Brewtools Gaskets for Pump Fittings
rb.gy/nuj7wv
you will need a joining 1/2” thread as the 34mm TC fitting is female and so is the thread on the elbowed portion of the water hose. These are easy to find in most plumbing departments
You will notice the plumbing on my condenser extends down lower than the standard kit. i just so happened to have a 2” to 1.5” reducer and an extra 1.5” straight pipe i wasn’t using so i decided to add it onto the end of my condenser piping.
This set up requires a total of:
33 X 34mm Tri-Clamps
8 X 1.5” Tri-Clamps
6 X 2” Tri-Clamps
1 X 3” Tri-Clamp
2 X 4” Tri-Clamps
Dont forget gaskets for each.
i think that’s everything….
16 сен 2024