Because of this channel I completely over hauled our barely used ‘73 Bridgeport. I never knew I would have such interest in restoring machines like this. Thank you H&W!
Outstanding instructional video. Terse, concise and to the point. No 15 minutes explaining what a screw driver is and how to use an open end wrench like nearly all the overly talkative videos show.
The bridgeport milling machine is one of the best machines for manufacturing precision parts. I was working for many years when I was young with an equal and when I watch the video I remember those times. Greetings from Spain
Awesome video. I ordered your rebuild kit to rebuild a Prototrak head. I’ve rebuilt quite a few machines but having this video makes it so much faster. Will definitely be ordering from you again.
Thank you very much Barry! I disassembled my Bridgeport top half and I’m in the process of putting it back together with new parts from your company. Everything has gone smoothly thanks to you videos. Keep posting your videos. Thank you. -Rey
I need to thank you for creating these videos. With these I was able to breakdown and repair the bushings and bearings my own 2j head. I did need to buy a new motor pulley unit as my one was an old type and the new bushings didn't fit. Because of your work, the whole process was so simple and far easier than I anticipated. It also allowed my to better understand the machine and I feel a lot more confident in using her now. Keep up the amazing work!
Thank You for the great videos. I will definitely be re-watching as I rebuild my Bridgeport - and when I need replacement parts- H&W will be first on my list when I go shopping.
Men, you really know what you're doing, a very helpful video, thank you for your dedication and for passing your knowledge and experience. It's greatly appreciated.
Thank you Barry and H&W. I use a series 1 two HP and I'm pretty sure the brake shoes are on their last legs. When tightening collets I really have to swing on the brake lever to hold the spindle! I could not imagine doing the teardown to get to them without first seeing how it's done. Excellent tutorial, no mess, no fuss. Thanks again form the U.K.
Shout out to H&W! They are THE place for any info , problems or parts you need for your genuine Bridgeport mill! From their rebuild kits with high-quality parts , belts and bearings w/diagrams and step by step instructions , to Barry's excellent step by step instruction videos. We bought 2 top end kits and the videos here made the rebuilding so simple. We didn't realize one of our machines was a 1 1/2hp and the other a 2hp. No problem! A very pleasant phone call to Debbie(?) got the different parts explained and exchanged.
Excellent video! If you guys ever get an Excello 602 in the shop I would love to see a video like this about it. I'm having a hell of a time working on mine.
Great video! Thank you for sharing the info on all of these segments -it will help me immensely when I rebuild my mill I like your assistant's tattoo - Mr Scissor hands.. LOL
Silly me was trying to pry the bull gear off without sliding out the high/low gear control assembly. Must have rewatched the video 10x before i realized
There isn't a bearing at the bottom of the motor, so you wont have to worry about checking that. Usually with clunking coming from the motor area its because the bushings need to be changed out on the Adjustable Vari-Disc. You will have to take the disc off of the shaft to check it. We do have a video with directions on how to change the bushings. If you want to call and talk it over with a tech you can give us a call: 1-800-285-5271
@@HWMachRepair Thanks for the info, I'll definitely check out your video. You can hear the sound mine is making at the end of ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bq988KFv-5I.html if you're curious.
Best job ever. Great technology u ppl had got. CV belt in cars these days. U got that years back. Far West invent n build. Near east copy n earn n enjoy.
Hi Barry, great video mate, to the point, very instructional. I have actually watched it 4x now as about to do a teardown on my head as the spindle has seized. Can you tell me why this head is being stripped please, what were the symptoms/problems before you got it. Is it possible that the head spindle shaft bearings seize very often? As I mentioned, my spindle has seized, any advice for me to watch for. I hope you also have posted a video on putting it back together again. I can't find a Bridgeport dealer here in Australia, if I need to get parts from the States can you suggest a good dealer please. Keep the good stuff coming mate, Cheers, Gordon
Thanks Gordon! The head that I was tearing down was in for a general rebuild. This head was just in general poor condition with worn out bushings, belts, bearings and many other things. If your spindle is locked up and you have a variable speed head you don’t have to disassemble the entire head, you can just remove the spindle from the head by following our video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-T1YJQUpNuaQ.html As far as a dealer goes, you are correct, as far as I know there are no dealers in your part of the world. We do ship quite often to Australia and we can always quote you shipping if you get in touch with Virginia at support@hwmachinerepair.com. Our website for parts is: www.machinerypartsdepot.com Let me know if you have any additional questions.
If you remover the three 11/16 nuts on the bottom of the bull gear assembly, can you lift the top half off the machine without fully tearing it down? I have to replace a quill dust cover and am hoping to do it without tearing down the whole top end. These videos are great!
In the interest of helping someone else with this who stumbles across this video, you can get to the quill dust cover through the bottom if you take out the spindle and quill. No need to disassemble the whole head to get to that, although you may want to buy the "how to rebuild a bridgeport" manual off of ebay.
No, the two machines are not compatible. We may have parts that will work with the Frejoth but I need to know what you are needing and we may need some measurements. support@hwmachinerepair.com
Refreshing to watch how a pro gets the job done. You don't get to be that fast without doing a couple of hundred of them first I'd guess. Any thoughts or tricks on getting the broken thread from the knurled knob out of the feed reverse control that I stupidly broke while moving mine Barry? It's snapped off below the surface. It's on a Taiwan Bemato built mill that I'm sure was cloned from a step pulley Bridgeport since all the controls are the same and are all in the same location if that makes any difference.
The good news about that broken screw is that it does not bottom out so many times you can get a pick and unthread it with that. If that does not work I use a Dremel with a thin cutting blade and grind a slot into the broken screw. I then use a very small screwdriver to unthread it. You may have to cut into the outer shaft a little but it will not be seen once you install the new feed reversing knob.
We just ordered your variable speed head rebuild kit. I’m excited to tear into this nasty old head. So far I’ve discovered the gear housing plate is missing. How critical is it? Please let me know if I need to order a replacement. Great video by the way..
That 'last component that was dissembled at the 18:10 min mark - can that be removed with the motor, back gear still assembled? I.E does loosening those castle nuts allow you to remove everything above the downfeed engagement lever as one assembly?
Yes, you can remove the bull gear housing as well as the rest of the upper head in one piece. You have to remember that it will be very back heavy because of the motor and when you put it back on the quill housing assembly the spindle spline must line up with the spline in the splined gear hub.
It is actually very different and easier to change out both belts on a step pulley than a variable speed. You have to remove the motor from the belt housing. You can do this by removing the locknut and handle from both sides of the motor that allow it to move. Slip the v-belt off the motor pulley and you can lift the motor off. For this next step you will have to lower the quill to the absolute lowest it can go. There are six socket head cap screws that hold the belt housing to the bull gear housing. Remove all screws so you can lift the belt housing and assemblies off all in one. The timing belt will have to be slipped off the timing belt pulley. This is easiest with the quill all the way lowered. Turn the belt housing upside down and you can remove and replace the v-belt. At this same time you can remove and replace the timing belt then put everything back on. You do not have to remove anything that has to do with the cam ring. If you have any more questions please give me a call.
The original 6F board isn't available anymore, so you will have to use the 6F upgrade kit. It comes with the board, mounting bracket, and instructions to wire it correctly to the 6F. machinerypartsdepot.com/product/038-0217/ We have 3 in stock as of today and if you have any questions, give us a call 1-800-285-5271
There is for a Step Pulley, but not a Variable Speed. We suggest using a phase convertor. We sell a solid state phase convertor that we highly recommend. If you have any questions you can call us at 1-800-285-5271 or you can see the convertor here on the website: machinerypartsdepot.com/product/pc02vs/ We also have a new video coming out soon that shows you how to wire one up.
+The Texas Gun Guy Yes, the housing that the spindle is located in is the same for both the Variable Speed and the Step Pulley type head. If you have any questions or run into any problems give us a call and ask for Barry. 1-800-285-5271 or 260-422-0020.
+H&W Machine Repair and Rebuilding: Thank you guys. I've rebuilt this head with your help already, you were spot on with the parts and services I received, and for that you have a customer for life. I now have to rebuild the lower end, and knee, it needs to be scraped 😵🔫 I'm going to send it out for that. Do you guys offer scraping services?
If you are working in the upper half of the head, most of those repairs can be done with the head still attached to the machine. For work in the quill, you may have to remove it, depending on how what you are doing. We have a customized table in our shop that can hold four heads at once, but it wouldn't be hard to make a small workstation for one head, you just need a workbench and some steel to make the bracket. I would post a picture here but RU-vid won't let me. If you want to email me at support@hwmachinerepair.com I can email you some pictures, or you can call 1-800-285-5271 and talk to Barry. He has done a bunch of on site repairs and he can help you figure out the best way to complete the repair you are trying to make.
There can be several different issues but, the most common would be an issue with the adjustable vari discs and the shafts they move on. The issue usually lies with the motor vari disc and shaft so, taking off the motor will generally give you a good idea on what is causing the problem. You could also have a problem with the speed change assembly. The tilt plate could be bent, the chain could be broken in a spot, or some other small issue. Give us a call if you would like us to help over the phone: 1-800-285-5271 / 260-422-0020
The tension in a Bridgeport is actually created by the spring on the motor vari-disc. You may need a new spring if you are having issues. Give me a call at 1-800-285-5271 if you have any questions, or would like a new spring. I think a new one is around $30, or I could get you a good used one for around $15.
Hi this is Alan it's my mill Robin is talking about, it's an Ajax Turret Mill is that something you would have parts for, I'm also looking for the replacement plastic bushes for both pulleys I'm in the UK so bear that in mind. Regards Alan.
Hi Alan, I don't have a source for Ajax here in the US, but it looks like they are still being made in the UK. You can try contacting them directly: 44 (0)1590 67600 or sales@ajax-mach.co.uk. If they cant help you, you may have to manufacture the bushings yourself. I can email some instructions if you need help with that, just let me know: support@hwmachinerepair.com
H&W Machine Repair and Rebuilding , hi I think I would like to make the bushings would you still be able to send me some information on the material I would need and any advice would be welcome on how to make them. Regards Alan.
music is quite annoying when you speed up some of your shots, please forget the added music, it adds nothing ! The videos are informative and stand on their own without adding someone's sad music choices !