Looks like it will move but that clutch will not last with all that weight unless you live in a totally flat neighborhood. It will be a good time watching you build it. Looking forward to the suspension!
Убил бы. Я от наждака после правки резца отхожу, воздухом обдуваюсь, не дай бог хоть одна песчинка на станину опадет. Сальники направлявляшек каждую пятницу мою, а то и меняю. Станок 16к20 1979года,на метре 2сотки конус.
@@gerbourke1952 more accurate than using wood , and now post covid with all the screens in the shops getting taken down it could be a good time to stock up with perspex as well.
I love this idea. I am gearing up to cast an adapter out of aluminum to mate my opposed twin experimental aircraft engine to a flywheel and clutch for a MGB transmission and then to a driveshaft and rear for a replica 1928 Morgan RIP GN special hillclimb racer. I may do it your way. I wil be video-ing it either way.
You should cut some pipe that fits your bolts and weld them to your motor plate instead of all of them nuts. Looks good man can’t wait to see move great ideas
He knows what he's doing but unlike others writing if they being crule or joking others are friendly others just joking I can tell others hard to tell cause seems real but you more down to earth and like it and not cruel at all friendly and have opinion i like that but I think he's doing it to make it more sturdier like robots to make building sturdier
Yes me and you both like this guy he's giving us ideas and he's an inspiration to little kids and youth that can do this and not getting in trouble just building these yes we like this guy he's a hero of our society he's really motivating us like euroupeans did if we look at what they did
Nếu tui đoán ko nhầm hộp số xe 500kg..vậy thì phải qua hộp giảm tốc mới chạy nổi...góp ý cùng bạn để cùng nhau phát triển đam mê...tui khoái lắm mà ko có tg
Cái côn đó có vẻ không ổn bạn ạ . Liên kết giữa động cơ và hộp số nhờ vào lực quán tính của mấy búa văng bên trong cái côn đó mình sợ tải nặng không tải được .
@@Techchannel91 có thể bạn sẽ không vào số được khi máy nó chạy . Vì bản chất nó không phải là li hợp .mình chỉ góp ý trên những gì mình được biết . Còn thực tế bạn sử dụng bạn sẽ hiểu :)
Ok you have a lathe and machining skills. Please make proper spacers, after everything you made you used nuts as spacers. The nuts make it look horrible. Otherwise it's very cool.
You knw there's an easier way to remove a stud by putting two nuts on the stud and locking thm tight together thn undoing thm instead of welding a bar to thm. Also you can reuse thm for something else
I don’t see the point in the adapter plate, because it would be possible to put on chains or belts, the second would be even better, because the centrifugal, for example, in this case, will not live long and will quickly fail
У них мышление другое. Да и соосность там , плюс минус полметра, поэтому им похрену, что соединять, лишь бы соединить, а там трава не расти. , он думает, что соединив через проставки мотор, он достиг центрации. Бублик резиновый, соединил бы это , за пару минут, при этом соосность там , вообще на глаз может быть. Прежде чем что то делать, нужно им книжки умные читать, по компоновке, и соединении агрегатов. Альфа Ромео, Вольво, мотор впереди, коробка сзади. Первое через бублики, второе через сайленты , через трубу.