Build a Off Road Mini BUGGY using Engine 163cc - 4 Speed 

Добрый день! Креативность, конечно, на высоте, но... Боюсь, что вы больше будете ремонтировать этот автомобиль, чем ездить на нём. И самое главное - никогда не крепите рулевые механизмы на сварку, это недопустимо!

Keren anda sangat kreatip

Am I the only one who was impressed with the home made hydraulic press??

Ang galing mo ok Yan Ang Ganda, I believe in you woow, The Best ka,,

👍👍👍👍👍❤️❤️❤️👍🙏

Um grande abraço

Mantap. Slamat. Chukcest

Perfect

Parabéns sucessos

Не плохо получилось, но транспорт одноразовый. Ремонту не подлежит, да и ездить на нем опасно.

good morning. Oh! Amazing and cool is fine!😆👍️ But, da ho!😆

it´s is music ????,, belo trabalho .AMAZING

I really like to see this buggy with highpowered 4x4 eletric hub motors! :D

gawang pinoy. good job kaibigan galing

Quá đỉnh

This is important.... Read carefully... In this project, there is a great need for structural reinforcements in the front suspension, because of the way this part of the chassis was manufactured, the cuts made in the bars to bend it , compromised its final structure. The parts to be reinforced are between the swingarms, in this place add a whole vertical bar (no cuts) welded from the bottom part (Bar) to the topmost part, after adding crossbars between the bottom bar to the middle bar, and from the middle to the top bar, forming a horizontal V ( ◀️), weld a support between the middle bar (where the upper swingarm supports are welded) to the added central reinforcement bar, this will distribute the forces applied on these three points (on these bars), instead of only applying force to the middle bar, thus preventing it from bending and breaking... The reinforcement of the middle bar where the swing arms are installed, even the central column is not for because of the force applied to the suspension, and yes because of the welded bar at the end of it (Bar not curved in a single piece (pipe)), compromising the structure of this bar of the upper swing arm... Another very necessary alteration that you will have to make the structural reinforcements, it is the shock absorber support arms, which are at a serious risk of breaking, add a cross bar between the shock absorber support bar to the middle bar of the chassis (where the upper swing arms are located) , this will avoid a great effort in these parts of the chassis, and their breakage, it is vital that their reinforcement be done, to avoid this big problems in the future (The breakage of these structures could cause the overturning)... The last reinforcement but not least , it would be to add a crosspiece (A lock) on the chassis between the upper bars that are attached to the shock absorber supports (from the right to the left side), this will prevent the chassis from twisting in the future (warping, bending, or twisting) ... These problems, if not corrected, could cause the "Mini Car" to overturn and cause serious accidents with serious injuries.

What an awesome project

Cảm ơn bạn đã chia sẻ

Mantap

Deus abençoe Tudo de bom

Top show parabéns 👏🇧🇷🇨🇮

Parabéns só o que posso dizer no momento continue sempre.

Ban chế tác rất hay nhưng có một điều đáng lưu ý là trục dẫn động sau không có khớp thay đổi độ dài ngắn của trục một khi bánh xe nhún lên xuống trục này sẽ gãy đó là chỗ chưa hợp lí

Mantul Bosqu

Adorei seu projeto só uma observação faltou colocar o assoalho para os pés más parabéns vc e ninja abraço amigo

Me:“Oooo is dat a rock?” God: Yea

I fear the universal joints are at an extreme angle but the creativity is great.

Rapais vc é um gênio fazer caicha de transmissão de ré

فل فیل ویڈیو

Предлагаю скинуться пацану на трубогиб!!! 😉

Amazing super good

Good ideas and good knowledge, but you work with hooves instead of hands;😅

Amazing what this man does with an angle grinder and electric arc welder!

This is awesome and the fact is mostly handmade aside from the mechanical flaws i love it

Нет стабилизатора на передней подвеске.На скоростных виражах не заваливается? И как вибро нагрузки на больших оборотах и скоростях?Просто Я посмотрел,что центровка выполнена примерно,а о балансировке речи вовсе не было.

This thing is a complete deathtrap, it won't be long before somebody is severely injured through it, It's an extremely good attempt but Completely under Simplified, Structural integrity is off the chart..

A grinder and paint makes me the welder I ain't

👍👍👍👍👍👏👏👏👏👏👏

Top

Buen trabajo 👍

tracking is spot on... errrr ish

This guy makes me feel less weird for welding in sandals. I knew there were more of us out there.

Amazing BUGGY

Good work & good hand

This guy built a gear box out of scrap parts out of a box ……. Tony stark.

It must took you months to build this highly engineered kart you should put bigger wheels on it and race it Good Job!!

I am afraid your suspension will tear the bearing apart there is no travel in the connection, from back suspension to engine ...

A joy to see every minute !

17:38 the legendary technique

great music

Toptop

Good

Wo maske

Do you have plans to seal up the gearbox? How has it held up so far?

Nice👍

Bro Amazing 😯😯😯😯

Pretty good for peanut butter welding

Awesome build!! But maybe invest in a tig welder, or even mig Welder 👍

What about them county orange slippers! he had on them Bruce Lee Roy's

Cross between a go-cart and a dune buggy. How do you keep the dirt out of transmission?

grind the galvanized coating off before welding ,better welds and less poison in your lungs,if that's a concern at all.

Mama will be angry..since you've stained the house specially guest room. He bro. go and make her satisfied , happy and pleased. Follower from H.K.J ,,, ALWAYS BE HAPPY,,

Great job ,you can build your shop for full time business . 👍👍

có quả hàn tig nữa thì hết bài 😋

I noticed you can only weld in spots, if you want a good continuous weld- drag your welding stick faster when you use it it won't burn through, when it burns through it means you were in one spot for to long, or just turn down the welder, hope this helps

Thanks !!! beautiful workmanship !!! JESUS CHRIST IS LORD !!!! AMEN !!!!!!!

The front part of the Oscillating Arms are the ones that run the most serious risk of failure... Mainly because of the welding on the intermediate tube and the half-cut arcs to be curved. The suspension forces applied at this point are the most vulnerable and subject to breakage due to the welding of this tube (It is not the only curved tube). The front arches will be the first to fail because of their compromised structure, they will not be able to absorb and distribute the forces applied at this point of the chassis.... Unfortunately in this case this curved structure is only for aesthetics (an ornament). on the chassis. It will cause serious problems in the future if these errors are not corrected. A way to avoid breakage at these points would be to add a Triangle in this front part of the intermediate tube, canceling the forces applied to the arches, a Straight Tube welded between the intermediate tubes on the left and right, and a reinforcement in V between these intermediate tubes to the lower front tube of the lower swingarm reinforcement, this would distribute the suspension forces more efficiently, and avoid the previously mentioned problems with the front arches. I know this is a Mini Car and not an ATV, but with a few upgrades it could become a low cost one. Learning in this case making your own mini Car is most important in this story. Good job, hope I helped in some way.

Amazing work

Кастор? Трейл? Аккерман? Углы работы кардана? Нет - не знаю. Но за видео спасибо

Mantap kendera,an yg unik ,,sy PGN belih dimana ya tempt nya MW pesan

Muito massa 👏👏👏👏👏

Legend say till now those bearings still weldered

Bhai bike engine se banao na PUBG wala buggy bike ka wil lga ke Belding kar wil banao plz bhai 🙏🙏🙏

Là on a affaire à un génie et non un bricoleur du dimanche !😎🙀

Why would you weld your bearing races to the plating? I see in other videos you've used pillow block bearings.

The kill-switch is wrong, the rear axles have a funny angle, The gearbox seems like the most interesting part imo.

If harbor freight ever built a gocart

From start to finish u did a great job keep up the great work

Genial

This car machine is beautiful, my friend, but it lacks several things, such as headlights, red night lights, and headlights to see in the darkness of the night. My innovative and genius friend, greetings to you from Iraq 🇮🇶👏👏👏👏👏👏👏💋💐👌🏻👍🏻

Un lavoro molto ben fatto con un ingegno non comune : avrei rinforzato i duomi superiori degli ammortizzatori anteriori e il telaio e avrei messo meno obliqui i braccetti oscillanti la gomma spancia (nota che quando sei salito sopra tendono ad allargarsi sulla carreggiata ) questo è il mio modesto parere comunque i miei complimenti per un lavoro di studio e passione

Можно приобрести редуктор коробки передач в точности как у вас? Сколько это стоило бы?

Amazing 🏅🏅🏅🏅🏅🏅🏅🏅🏅🏅🤗🤗🤗🤗🤗🤗🤗🤗🤗💖💖💖💖💖💖🌹🌹🌹🌹🌹🌹🌹🌹🥇🥇🥇🥇🥇🥇🥇🥇🥇🥇🥇🥇🥇👏👏👏👏👏👏👏

Gooooooooooooood job!!

Awsome video love the in depth film on how you made it all brilliant work

Need to lower the suspension so the angles of the arms are not so sharp at ride height.

Wonderfull congratulacion

Too much angle on the suspension and U-joints

you need to add adjustment to all of these chains for when they stretch

You should buy some bearing blocks.

Amazing!

Sir kaha se ho aaap

Amazing DiY

Buy a TIG weld man, its better than ordinary arc welder

Buenas ideas y buenos conocimientos, pero trabajas con pezuñas en vez de manos ; muy burdo tu trabajo.

this is a really cool thing you have built but i have some concerns like the lack of any sort of lubrication on your drive train im afraid you will be doin a lot of repairs pretty quickly

"Build an Off Road Mini Buggy..."

This thing is awesome. Waaaaay over engineered which is a compliment. I feel like you could get more speed (while losing the reverse and gears ) and just go straight centrifugal clutch . But then again the gears is what kinda made the whole build more interesting

Cara vc é muito top, parabéns.