Build your own DIY Bow Press and Draw Board all-in-one system

Подписаться 113

Просмотров 9 тыс.

50% 1

Parts I used:
Fingers: www.ebay.com/itm/204851567013
October Mountain Products archery scale: www.amazon.com/gp/product/B07...
Winch: www.amazon.com/gp/product/B09...
Plastic caps: www.amazon.com/gp/product/B0C...
All thread: www.homedepot.com/p/5-8-in-11...
Aluminum rod: www.homedepot.com/p/Everbilt-...
2” steel tubing with 1/8” wall
1 ½” steel tubing with 1/8” wall (if you can find 1 ¾, that would probably be better)
½” flat stock for eyelets
Flat stock for feet
5/8” nuts
Some videos I learned from:
Bow Press part 1: • Homemade bow press
Bow Press part 2: • Homemade bow press Par...
Bow Press: • EASY and FREE - Bow Pr...
Draw Board: • How to Build a Bow Dra...

Хобби

Опубликовано:

29 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@WrxRallyFreak 25 дней назад

Nice Job! I have been contemplating doing this instead of spending the $1000 on one. Thanks for the links.

@ArchersAnonymous-nb4ym 16 дней назад

LCA green press is around $400.

@ArchersAnonymous-nb4ym 16 дней назад

Nice build man

@kennylainhart7148 25 дней назад

Looks good man!!! 👌

@kellymondragon3404 15 дней назад

FYI...I decided I don't like the angle of the bow when I hang the bow on the bar stock for the draw board. I was worried the string might derail. So I've just started hanging the bow on the square tubing. It works better because it keeps the bow perfectly level. I may even cut off the bar stock since I won't be using it for the draw board anymore.

@mansalaija 25 дней назад

Nicely done! 👏👏👏 I’d like to start working on my own bow but bow press and draw board are $$$$. Too bad I don’t have the equipment/tools to build this.

@eddycastillo6185 11 дней назад

One quick question! Did you use a bearing at the end of the 2 inch tubing, mounted on the all thread. This bearing will support the all thread and turn smoothly. Great build! I like your design where you have the two plates welded to the square tubing. thank you for sharing your design.

@kellymondragon3404 11 дней назад

I did not, but that is a smart idea. It is still pretty smooth though. I put grease on it and it has never bound up.

@kennylainhart7148 22 дня назад

Could you show the double nut ,on handle!!? Mine is sliding way out before it connects for pressing etc!!

@kellymondragon3404 18 дней назад

It is as simple as putting two nuts tight together on the other side of the handle. The positive engagement will keep them, and your handle, from moving out.

@kennylainhart7148 18 дней назад

@@kellymondragon3404 thanks 👍👍

@ericcampbell6572 26 дней назад

How long is the tubing for the press

@kellymondragon3404 22 дня назад

The bigger tube is 28" and the smaller tube is 26". Should fit pretty much any bow you can throw at it.

@billstiger473 24 дня назад

You have a Bill Of Materials and cut list

@kellymondragon3404 23 дня назад

The materials are in the description. I'll add a cut list soon. I did measure the tubes. The bigger tube is 28" and the smaller tube is 26". Should be able to fit almost any bow you can throw at it.

@matthewfahey774 28 дней назад

You built this for 150$-200$?

@kellymondragon3404 26 дней назад

Yes I did. However, like I mentioned in the video, I had most of the steel. So all I bought were the fingers ($80), the aluminum rod ($10), the winch ($25), plastic square plugs ($10), all-thread rod ($10), and spray paint ($10). I haven't priced metal lately, but I bet you could get it all from a scrap yard for less than $100 if you don't have any laying around like I did.