No video :(

CAN AM MAVERICK X3 RIDE HEIGHT ADJUSTMENT

Подписаться 683

Просмотров 34 тыс.

50% 1

In this video I demonstrate how to set your ride height with an aftermarket dual rate spring kit on a Can Am Maverick X3. The same basic procedures are still relevant to any UTV using a dual rate spring set up. So there is still some good relevant information you can gain no matter what machine you drive.
Note: This is just one variation on setting ride height, and we will not be following the factory settings procedure, or the Fox Race Tune procedure.

Опубликовано:

24 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@Bullyveldt Год назад

Very clear, very easy to understand. Awesome!

@grumpyg9350 Год назад

Better than ST video. Very clear and great video close up.👏🏻👏🏻👍👍

@SideX_Each Год назад

I should do it again. Learned a shit load about making video since then lol!

@jamesthomas5580 2 года назад

Great job and thank you for making it simple for a “bubba” like me. Keep the tutorials and videos like this coming.

@SideX_Each 2 года назад

No problem brother hit me up if you have any questions!

@davidhotton3093 2 года назад

Great info, great job. Keep em coming..

@SideX_Each 2 года назад

Thanks man. I will keep em coming. No real method to the madness, just filming whatever I happen to be doing at the time. Too bad I didn't start 2 years ago!

@SteelTallon Год назад

I bent a rod my 1st time out, because I didn't do this tune. Lesson learned.

@SideX_Each Год назад

Sometimes we learn the hard way. But breaking stuff is not uncommon lol. Happens...

@ShockTherapyllc 2 года назад

Nicely done!

@SideX_Each 2 года назад

Thanks guys👍. Just wish it wasn't one of my first video attempts and not on a front porch! I could definitely do a little better now haha. Quite a learning curve making vids. Not as easy as it looks.

@craigprice2286 Год назад

What was the measurement from to of the shock the the first locking nut? Please and thank you.

@SideX_Each Год назад

I think I mentioned it in that video. But yours is not likely going to be exactly the same as mine. You just do what you have to do to get the desired rude height.

@mandytuning 2 года назад

The front preload compress 1"=1/2 increase of height

@SideX_Each 2 года назад

On stock springs perhaps. Not that its written in stone, but Shock Therapies springs it's approximately the opposite. Just a general rule of thumb for a starting point. Either way, do what you gotta do to get the ride height you want👍.

@mandytuning 2 года назад

@@SideX_Each what i mentioned is what ST says on one of his videos.and makes sense since front aren't straight.but yea,at the turn that bastard ring until your happy

@ICOM1219 2 года назад

1/2 spring compression = 1" of ride height. Correct my friend.

@randyd2093 4 месяца назад

Did this adjustment make the car ride a much rougher

@RubSomefastOnIt 11 месяцев назад

arent your front shock resiviors supposed to be on the inside? that's how mine came stock. am I missing something?

@user-yn3is9kf3p 6 месяцев назад

People flip the shocks to give it a cooler look...You have to trim the inside of the plastic where the shock comes through or else it will rub hard when your shocks compress while drivin