Can I Even Get It To Print!? - Kingroon 3D Printer Review 

I've had this printer since Aug 2019. My first printer and I still love it. I did some upgrades on it like hardwiring the power supply to the motherboard, new spool holder, adding a parts cooling fan and upgrading the firmware to Marlin 2.0. Those were all cheap upgrades and I think it prints pretty damn good. Very happy with it still after 6 months of using it.

I just got this 3-D printer and all these problems he pointed out I couldn’t find looks like kingroon saw this video and fix their problems that they had with their printer. Except with the lead screw and the filament That was the only problem i found but everything else on this printer is great!

When I receive mine; I will first print out an extension for the screen to advance 2-3 inches and if it works; I will give out the model data and explain how.

ya your not going to find a better beginner printer for the price, color touchscreen, heatbed, linear rails, etc. i looked all over the internet and thisprinter i found was great by the reviews. most of the mistakes in this video were caused by you, no offence.

that under extrusion looks like you didn't seat the bowden tube tightly onto the hotend. i did the same thing when i swapped mine out. it'll print fine once the plastic fills the gap between the hotend and bowden tube, but the resolution is garbage afterwards. i'm sure the printer can print at a quality that competes with some of the $500 printers.

Thanks for that review 🙂

do you know of anywhere other than the SD card to get their slicer? I had just received mine and it prints the two files on the card but anything else I tries fails. I'm curious if I have it set up wrong in the settings, such as maybe reprap vs marlin?

You must have got a very 1st model as I have this printer and I love it. No problems what so ever. The Guardian Model is the extruder knob.

I’m in the market for a 3D printer and this helped

could someone please link a download for the slicer

How did u fix the gcode when u said it was not printing cause it had space on it im new to 3d printing and learning gcodes and everything from 3d modeling my printing was 3 hrs but it only printed 1 hr because of the space and when i check the gcode for that i see everything is good no spacing but its probably because i didnt see it please reply to this i need to know

i have it and use it everyday. love it. its top 10 for best printers on market for the price.

My issue with the print bed is that it's impossible to get the thin pla layers off.

I got mine last week, and all the file on the sd card have vanished. Every time I put it in the computer it says to format the card. Also when I print mini (characters mostly) I get lots of strings and sometimes no face details. I really need some help.

I just got this 3d printer for christmas, and it's alright. The printer came in very good condition with no broken or slightly moved parts, but the .gcode files for one print I wanted to print was messed up and way shorter than it should've been.

Hey my bead appears to be glued down. This printer was bought in 2019 and gifted to me a few months ago did the previous owner glue the bed down? kingroom kp3-3dp180

I bought one but I need you mind if ya help me please?

the slicer looks just like creality slicer 1.2.3 which is the same thing as u said its a reskin of a older version of cura but it works so well for my ender 5 im curious tho if u could take the numbers from the slicer that came with them an move them into cura so u could take advantage of all the settings it offers over the reskin of older cura.

Nice and informative.

Hi, do you need to buy a filament censor every time it runs out?

Can you make kashyyk clone Trooper armor with it

My Kingroon came with sample filament, but the filament was extremely brittle and kept breaking as it was going through the extruder. Any tips to fix? Do I just need to get better quality filament?

I may get this for Easter. Besides filament what else do I need for it?

Hello, I have the printer but I accidentally deleted the KingRoon3D software (the exe file(. Can you please share a link so I can download it Thnx

I can't keep the t-nuts oriented correctly in assembly.

It definitely isn't perfect, but its not bad, print quality can always be improved with a parts cooling fan, and the under extrusion can be fixed in the software. I'm glad I chose this as my first printer, it has issues but that's the best way to learn how to fix them. The facebook group is awesome too, everyone is super helpful and the company is there to help as well.

In canada its 219 cad $ but thanks for your awesome review , im going to get it for my first printer !!

What type of filament do you use,

Hello where can I download Kingroon3d software for printing

I think you had underextrusion because you were printing in volumetric mode

Hello, what motherboard inside the printer? 32bit? What drivers of step motors?

they have changed all the issues u pointed out in this video. i got my kingroon kp3 about a month ago an it has been the most hands off printer ive ever owned. all ive done to it was print a sd card slot cover to help with directing the sd card into the slot and a part cooling fan duct which i did end up having to model my own cause they must have changed the x carriage cause all that i tried didnt line up with the hotend. an u should be able to take the settings from the kingroon slicer an move them to cura. the power jack has been changed an it fits nice an snug now an dont stick out as much as the old one. the filament run out sensor is changed an is lined up with the extruder so the filament has a straight shot from the run out sensor to the extruders hole where it goes in. the end stops look different on mine too an dont site cover by the x motor cover. they have listen to the community with this print cause every early review of this print points out all the same things an they are all fixed on mine. im guessing thats why the x carriage is different on mine also. anyone else that has a new kingroon kp3 let me know what part cooling fan duct you used. id like to have a dual fan setup if possible. i just remodeled the mount for a fang to get something on it and right now im using 3 different slicers the kingroon slicer for my kingroon kp3, creality slicer 1.2.3 for my ender 5 and cura 14.07 for my anet e10. they all came with the printers sd cards and have worked better for me than the newer cura profiles ive found, but ive point out that these slicers are a reskin of a cura 3.xx version so u should be able to move the settings over to cura an they work the same in a few facebook groups an the ones that tried it reported back with success so i plan to make a profile for each of my printers on the newer cura so i can take advantage of all its options i just havent found time to site down an copy everything over. if anyone has tried this let me know how it worked out for u an if u had to do any tweaking. and for the incomplete gcode. ive had this happen before with my ender 5 using the creality slicer. i think i closed the program out before it was able to finish writing the gcode to the sd card. either way it was the same as urs. would get to the end of the gcode an just stop. my temps would stay at what it was set to til u canceled the print. not had it happen since. after realizing the gcode wasnt complete i figured i had pulled the sd card before it was done writing an now i make sure the files is written to the sd card an eject it, if its still being used it was pop up something asking if u want to continue retry or cancel. i always cancel an give it a few seconds an try it again an it always ejects then and ive not had the issue since. and i switched to better sd cards from the cheap un marked ones that came with some of my printers.

How long did each print take? Thanks!

so most of your complaints are things that you just needed to learn the machine. all printers need a little honing into it's particular qwerks. overall a nice little printer with a small size over all yet with a bigger than normal print size.

Thanks fro reviewing this printer, its cost about 150$, I had made a video also.

Helpfull

I recommend you to re review this printer, it got a whole lot better.

Really really

That printer was't designed by kingroon.The staff of kingroon stole another company's drawings and manual.And that was the reason of there manual was wrong.So i don't recommen it.

I just ordered this and this is the only bad review

I got mine for $107

Should have done more research, I guess. I got this printer as my first 3D printer. Have had issues with it from the start. I got it because of the price. Like they say, you get what you pay for. Biggest issue is not having any kind of manual. I am used to having a manual with any piece of equipment I get, be it computer or radio. Got a few good builds out of it, but had to replace the bed. First one came apart. Now I can't get filament to feed. Guess I need to figure out how to take extruder apart. I guess it is good to know that others are having issues. Not just me. John KB5GGO

Are you the same person that finds everything WRONG with any printer that doesn't cost an arm and a leg...well if you find something that you know is not right than fix it tell others how you fixed it also send an email to the company but this video is like l found this and that and that and this and is very discouraging to others.

lots of user error in this review. I wouldn't expect to have any more printers sent to you for review.

For free, I’d play with it. But not interested in fixing it up, to get it workin, if I bought it.

The more I watch the more i cringe. Different printers require different profiles. smh.

This guy doesnt know the difference between a shark and a dolphin

Can you 3D print a gun and give it a review?

no printer in the world can print that dog well without supports. You are way out of your depth.

imagine printing pla plastic at 215 C, and making a bad review some people man. have u ever printed pla before omg. 180-200 C is the recommendation, in which 200 is a bit high.