Can you reuse head bolts? Or why can’t you? , The in Depth video of Why 🤷🏻‍♂️ you may be surprised

Подписаться 121 тыс.

Просмотров 32 тыс.

50% 1

So for several decades I’ve been reusing head bolts and I’ve had people lately question me on why I could do that and tell me I could not do that…… but not really given me any reason other than that’s what they were told…… so I decided to make a end up the video of why from a mathematical standpoint and my personal opinion and if it is possible and why it is possible….. I hope you dig the video you’re more than welcome to give me your thoughts,
In a nutshell though The compression ratio on this engine is 9.8 to 1 this is not a super high compression ratio and since the cylinder generally has only 125 to 135 psi from the factory of compression and because there’s 10 large bolts holding the cylinder flat to the engine and because the bolts only stretch 1/16 of an inch which is 1.58 mm leaving a gap of almost 3 mm between the bottom of the bolt where it goes into the head gives me good reason to believe that I can reuse these bolts unless you believe that your bolts are different lengths I say reuse them but this is just a personal opinion I can’t be held responsible for what you do in your garage. …….. on my personal cars I’ll do whatever I want if I was working on your car I would do whatever YOU want….. yeah I’m a hoe like that lol
We would very much appreciate if you would watch the whole video .(sometimes I’m fun) So you can inform yourself with all the great information that I put in my videos and God bless. I hope the videos helpful for you!
And Thank you for viewing!
Have a great day
FOR THE BIGGEST AND BEST PARTS CATALOG, CHECK OUT DORMAN PRODUCTS AT: www.dormanprod...
“You can’t really break it if it’s already broken!”
Please subscribe!!!
if you want to reach out to me and get a message to me hit me up on clays ac and auto repair on the facebook And if you have any questions it’s easier to message me straight through Facebook
Why should you Subscribe to my channel ? I constantly make these videos that show you how to use your tools and show the techniques that we use in our auto repair shop every day. And all it does is help me send you stuff . I do not sell your information I do not solicit you. all it does is add a couple 100 thousands of a cent to me . And it cost you Nothing ! you would only be helping me . And hopefully i was able to help you !! So please be kind and enjoy!!
The Clay Way nor makers,producers and installers will not responsible for ANY damage that happens to your Vehicle or if we are incorrect about any of my information contained in this or any of our videos ,any accidents that happen while you’re performing the procedures that We explain And you perform or anyone else perform. The Clay Way will not be liable in Way shape or Form. By viewing content you are agreeing to these terms.
This video is property of the Clay way Channell and root 66 productions. No portions of the video can be copied and re-distributed in any shape or form without written approval from root 66 and or the Clay way Channell!
Products that I use quite often.
PB blaster penetrating oil
Lisle tools
Snap-on tools
Matco Tool‘s
Dorman Products
List of cars names
Chevy trailblazer ,GMC envoy , Cadillac Sts ,Cadillac SRX ,Cadillac Escalade, Chevy avalanche ,Chevy Silverado ,GMC sierra ,Toyota RAV4 ,Honda CRV, Acura MDX, Volvo XC 90 Volvo S 70, Audi A4 , Audi asix Audi S4,Volkswagen Passat, Volkswagen tiguan Chevy Equinox ,GMC terrain , Chevy Silverado, GMC sierra, GMC Acadia ,Chevy traverse,Pontiac Grand Prix ,Pontiac G6, 1995,1996,1997,1998,1999, 2000, 2001,2002 ,2003, 2004, 2005 ,2006 ,2007, 2008, 2009 ,2010 ,2011, 2012, 2013 ,2014 2015, 2016, 2017 ,2018Jeep grand Cherokee ,jeep commander ,jeep liberty,Jeep patriot, 1995,1996,1997,1998,1999, 2000, 2001,2002 ,2003, 2004, 2005 ,2006 ,2007, 2008, 2009 ,2010 ,2011, 2012, 2013 ,2014 2015, 2016, 2017 ,2018 Chevy impala ,Chevy Malibu, Ford F150, Ford escape ,ford fusion ,ford Taurus, Dodge Nitro ,Chrysler 300 ,Dodge ram. Pontiac Sunfire, Pontiac Sunbird ,Pontiac Trans Am ,Pontiac transport Chevy uplander. Mazda CX7 ,2001,2002 ,2003 2004 ,2005 ,2006 ,2007, 1995,1996,1997,1998,1999, 2000, 2001,2002 ,2003, 2004, 2005 ,2006 ,2007, 2008, 2009 ,2010 ,2011, 2012, 2013 ,2014 2015, 2016, 2017 ,2018 Mazda CX9 ,toyota tundra
Toyota 4 runner ,2001 2002 2003 2004 2005 2006 2007 Ford explorer 2001 2002 2003 2004 2005 2006 2007 ford F150 ford F350,ford F250, 2001 2002 2003 2004 2005 2006 2007Jeep wrangler , ford Windstar,jasper engine, engine rebuild, best repair shop in grand rapids michigan, best mechanic in grand rapids michigan, (im not), ratchet strap tie down.

Опубликовано:

25 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 82

@pjj12345789 2 года назад

On a boosted vehicle always change them… they can snap when you tq. them down.

@sharpcarco 2 года назад

I definitely agree with you. I think at one point in the video I did mention that. If you’ve got thousands of dollars in your engine I don’t think you’re even considering reusing the head bolts.

@privatedata665 2 года назад

I reused a LS Engine head bolt , it's now a hitch pin on my lawn mower . So there ya have it , yes you can reuse head bolts

@norain31 8 дней назад

2014 to 2019 gmc 6.2 first 22flb second pass 67flbs third 84 flbs in sequence gets you away from the 70 an 90 degrea ..Thankyou for such a good video ! couldn't get over why nerds have to make easy stuff so hard and waste hard earned dollars . Yer one of the smart ones Clay !!

@charlypr88 Месяц назад

As a aerospace technician I worked with thread rolling machines for a while and you can get away using the same bolts in a lot of applications. I know lots of ppl don't have access to a shadowgraph but with that you can see and measure the pitch and thread of the bolts. For automotive tolerance vs aerospace is quiet huge gaps and you can get away re using a lot of parts if the car don't have crazy miles..

@siliconvalleyengineer5875 Месяц назад

thank you for checking the depth of the holes, it would appear to be about .400 thousandths of space. You may want to tell your subscribers and viewers to use a botton tap which douse not have the long starting pointy end to chase those bolt threads, thats what i use. I reuse my head bolts too, but I install new crank mains bolts

@sharpcarco Месяц назад

Yeah, I would definitely never recommend this on crank or mains thanks for confirming

@maxpert1540 2 года назад

the oem bolt has an extended taper pilot tip and the aftermarket bolt has a flat bottom, that length comparison was not useful

@dave0z96 2 года назад

I work on Diesel engines and I have gotten away with reusing torque to yield bolts on connecting rods just fine on a 6068 John Deere, but the head gasket blew . The head gasket blew after about 200 hours . I changed the head gasket and it’s got around 12 thousand hours on it and it’s fine .

@antiochiaadtaurum3786 2 года назад

what do you mean? the head gasket only lasted 200 hours with the reused head bolts? and then lasted 12,000 hours with brand new head bolts? Did you install a new head gasket again? What you've said is about as clear as heavy fog

@dave0z96 2 года назад

@@antiochiaadtaurum3786 Yes one engine only lasted 200 hours with reused head bolts . After I changed the head gasket I used brand new bolts and it was fine . I have reused torque to yield bolts with a lot of success but I just don't like doing it after that 200 hour head gasket failure .

@MrPicoli Год назад

I changed my first head gasket on a 2009 3rd gen prius. I didn't know what I was doing so just went cheap and reused the bolts. It blew again 90k miles later. I'll change the head gasket again but this time I'll change the bolts...

@sharpcarco Год назад

I would also consider may be changing the way you drive my father-in-law has 400,000 miles on his Prius and has never had a head gasket issues… I’m just saying.. I think you kind of missed the point of the video

@ky-effect2717 Год назад

And another point to consider- torque isn't the best measure of clamping force due to the friction at the threads and at the bolt head. Bolts are like springs so if it stays stretched too far and didn't return back to normal then its clamping force probably decreased. It would be interesting to see the test done with a load cell.

@fullautocare4403 2 года назад

This is a very tough subject. When I reuse try, I just torque it about 3% more than spec to insure a bit more stretch so the bolt will grab the way it was designed. I've never had a single problem in 15 years.

@ek8710 Год назад

Do you re-use on boosted vehicles also?

@sharpcarco Год назад

No … conventional

@ArmyGrunt1986 Год назад

My opinion is that yes you can re-use them as long as they weren't over torqued/stretched or abused. However the price of new bolts vs the possible cost if you use bad bolts. So to me the $70-$150 is definitely worth the peace of mind knowing my engine won't go into Self-Destruct mode. Again that's just my thoughts.

@sledgenwedge 5 месяцев назад

For a 150 bucks, you can get Arp headstuds.So why would you bother buying torque to yield

@himeedajew Год назад

Hey thanks for the info! Not to be the backyard youtube mechanic heckler im just asking.....i recently did a head job on a 3.7 jeep Cherokee, i could have sworn it said in the repair manual the bolts were not torque to yeild and to just make sure bolts werent necked.Maybe some models are different?

@sharpcarco Год назад

Yeah, I don’t know. You’re probably right different years probably had different Bolts, even though they were the same.. head bolts are going to stretch no matter what because of pressure.

@rotate85 2 года назад

As long as the bolts were never over torqued you can safely reuse it. However it does require a higher torque on its second use so that it has the same clamping force. I would say 5-10% more. I would not use it for the 3rd time. If you’re worried about the bolt bottoming out then put a good quality washer and call it a day.

@sharpcarco 2 года назад

I guess I wasn’t very clear but I wasn’t worried about the ball bottoming out I was showing people that it wouldn’t bottom out.

@dontibbitts9490 Год назад

Yes they will fit . But the yeild point is where the material will not spring back and start to stretch. It's a different curve for every material. The further you stretch a bolt past it yeild point the less force it takes to stretch it further until it breaks. Plus it lowers the elastic strength. Even if it's very small. Every time a combustion happens some of the power pushes the heads up and the head bolts act like a spring. They do wear out just like a spring. Especially if you have already stretched it further past it's yeild point. It may be fine for a while.. but if you want you head gaskets to last 100k plus miles.. listen too the engineers.

@ihopness1668 Год назад

Good info

@Toniez0 9 месяцев назад

This is an perfect opportunity for an experiment in my case what could go wrong 😁

@sa-ma-dhi 2 месяца назад

If you scared, go to church! Or buy more insurance. Take a risk, it's minimal.

@sa-ma-dhi 2 месяца назад

Brand new parts fail every day.

@LouiseTurner-x9z Год назад

I have been using K-Seal in the cooling system to seal the head gasket with favorable results for a few years. The latest problem is that oil is now getting into the spark plug wells due to brittle O-Ring seals under the rocker cage. I ordered a complete top-end gasket and seal set. How flat does the under-side of the head have to be in order to be considered flat enough so as to not compromise the head gasket? What is the safest way to UN-stick the valves head from the cylinder head? The car is a 1989 Honda Civic DX 1.5 Any helpful thoughts are welcome?

@sonoramurphree6538 5 месяцев назад

we had a problem with one of our head bolts on 2007 Cadillac escalade with 305 ltr .we could only hand crank motor half the way each direction and then it stopped .we torched to 22.2lbs as per our guide said.we removed the rods one at a time and tried to hand crank still it got stuck and continued to be stuck ,until we started on head bolls .any ideas about what's going on? motor has 250k on it

@raymondconnor5022 2 года назад

I've reused head bolts on every engine...which is many....never had a problem...ever

@edwardherrera2239 2 года назад

Happy Easter , Quick question would you use any type of threadlocker on the Headbolts ?

@sharpcarco 2 года назад

Should not be necessary no I wouldn’t recommend it.

@edwardherrera2239 2 года назад

Awesome !!! Thanks for the information and keep up the good work ...

@MrLoso19 6 месяцев назад

Random question I just had a head bolt snap when torquing down. Is it possible to re-use one of the older head bolts if I can extract the one that snapped without removing the head? If I were to take the head off to get this bolt out, would I have to replace the new gasket I just pressed in?

@alpha_cg5 2 года назад

I know you explained it, but does this apply for Honda head bolts too?

@sharpcarco 2 года назад

I’ve reused Honda head bolts several times

@alpha_cg5 2 года назад

@@sharpcarco okay gotcha, appreciate the info.

@bseries8826 2 года назад

Was wondering this as well. I know I have a super low mileage JDM K24A so I'm going to reuse it

@DjDestinyChicago 2 года назад

The first head gasket I ever did was on a Civic… I reused the head bolts and drove it for another year afterwards with no problem

@marknegrete9353 2 года назад

If I have an oem bolt that stretched out and bottoms out before achieving correct torque on head can I add some washers and not damage? Washers are not in the way of anything,

@sharpcarco 2 года назад

If I remember right there was about 6 mm to 8 mm of depth left inside the hole if it’s that long I would recommend replacing it the only reason it would hurt anything putting washers on it would be if it struck the cam. But if it’s that stretched I would consider buying new ones… And I’m about as cheap as they come

@marknegrete9353 2 года назад

@@sharpcarco thanks for the reply. I was measuring from the top of the head.which was giving me incorrect spec length. Also I was thinking it was bottoming out cause I had coolant leaking from head. Turned out to be three stud holes for the exhaust manifold. What a week . Thanks anyways brother. Keep up the great work.

@garylarson6386 Год назад

I liked the old hard bolts that you didnt stretch just torque, if you overhead and aluminum engine the new bolts stretch more and the head gasket leaks !!!

@ImNotHereToArgueFacts 9 месяцев назад

I just have 1 question... What would cause you to need to reuse the same headbolt several times?

@sharpcarco 9 месяцев назад

You’re taking the word several to literally….. I’ve rebuilt more than one engine. I’ve rebuilt several engines, so I’ve reused several head bolts. lol good try though if you don’t wanna reuse them, don’t reuse them like I said in the video I’m just telling you my experience

@ImNotHereToArgueFacts 9 месяцев назад

@@sharpcarco😂 I get it. Do you have any records for like torque to achieve 90° on a new vs once used bolt? OD just above threads?

@kellycoberly3634 2 года назад

So if you reuse them after they are stretched should you torque them the same? Polaris goes to 26 foot pounds plus 180 degrees. I wish I knew what the torque value was after the 180 degrees. It would seem after the first strech it might be better to just torque to the proper spec and not stretch again??

@sharpcarco 2 года назад

⭐⭐⭐⭐If you liked the video and want to show your support, you can use any of these links to purchase ANY ITEM you normally would off of Amazon and we get a small commission with no extra cost to you! Make sure to complete orders through the links! Thank You! DEWALT 20V Max Impact Driver Kit, 1/4-in: amzn.to/3y0vDRJ 5 Pieces Magnetic Telescoping Pick-up Tool Kit: amzn.to/3knxckI Magnetic Screwdrivers Set with Case, Amartisan 42-piece: amzn.to/39sTSxT CRAFTSMAN Mechanics Tools Kit with 3 Drawer Box, 216-Piece: amzn.to/3Nux6UL ANCEL V6 PRO Bidirectional Scan Tool: amzn.to/3wRcvDy CASOMAN Master Torx Bit Socket and External Torx Socket Set, 60-Piece Set: amzn.to/3NbWUpe Thorstone No Spill Coolant Funnel Kit: amzn.to/3m1dADS

@raullopez9639 Год назад

Thank for you video 👍

@stellarv5689 Месяц назад

I would do this with oem bolts

@sharpcarco Месяц назад

Yeah, that’s kind of the point. I’m getting it definitely wouldn’t reuse with some cheap knock offs.

@flintknappingtools 3 года назад

God Bless!

@vendetta1306 2 года назад

Much obliged

@roryt420 3 месяца назад

Thanks

@kingkotkot2341 2 года назад

100% love your video

@sharpcarco 2 года назад

Well thank you for taking the time to say so we greatly appreciate it welcome to the Channell we’re very happy to have folks on board just like you

@harrish1978 Год назад

Hey mate my Manuel says loosen to on in the torque procedure. Is it mean torque to specs then loosen it then torque again ?

@jab5521 Год назад

You can resues toilet tissue it will work. 😂😂

@sharpcarco Год назад

😂😂😂 but only if you really wanna save the landfills…

@hastyhillfarmand4x480 2 года назад

Couldn't I just over torque them by 1 lb?

@lanceamerica9405 8 месяцев назад

Face diaper = done

@sharpcarco 8 месяцев назад

🤔lol funny thing is you have no idea why I’m wearing the face diaper and it’s not because of the reason you think it is….. 😂 You see during Covid the dog ate my false teeth and Governor Gretchen Whitler shut down all the dentist…. Yeah I never got those teeth replaced, but I’m not really embarrassed about it anymore.

@PaulHenreid Месяц назад

ten big bolts, cmon, torque to spec and reuse.

@sharpcarco Месяц назад

This !!!!

@lucientjinasjoe1578 8 месяцев назад

If i tell you that in the third world mechanics in the hinterland welding these broken head bolt and torque them to specification

@MoeLarrycurly1 3 года назад

👍🏼👍🏼👍🏼🏍🖖🏼

@user-ds9zd8eq6u 3 месяца назад

New Bolts are Chinese! Use the old bolts! Unless you you wanna buku bux on ARP!

@clickonmike Год назад

The last time I did a head gasket was in 2003. A 1994 ford straight 6. It even said in the work manual you could use the bolts twice. Also to mark the top of each bolt with paint as a reminder.

@BP021 Год назад

Reused many head bolts. Even on boosted cars. Never a problem

@sonoramurphree6538 5 месяцев назад

sorrey the motor was a 403

@electricbaylinergoesfishin870 Год назад

youre by yourself, talking to your hand held camera and wearing a mask

@sharpcarco Год назад

Yes, because I was embarrassed….. you see governor Wittler… shut down all the dentist during Covid… and before Covid I was doing good business, so when Covid came along, I had money but not for long because everything was shut down… including the dentist, which I could’ve really used because the dog ate my false teeth…. Had nothing to do with Covid

@skatertrash4205 Год назад

Il with u brother am poor too😆 no rich person realize how crap these parts are

@Toniez0 9 месяцев назад

If we just use our head for a second there should be no reason you cant reuse several solid metal bolts

@galesams4205 3 месяца назад

This is such bull shit about not reuseing head bolts this is just parts supplyers wanting to sale more parts. Im a diesel mechanic . I can tell if there is a STRETCHED head bolt or NOT. On cumming, cat, detroit, the old HEAD bolts are reused on these 500 HP engines.