Carbon Fiber Bodywork

Подписаться 316

Просмотров 2,6 тыс.

50% 1

In this video, I build a full carbon fiber belly pan and upper fairing for my race bike. After finding that my previous belly pan was too wide at the rear and scraped the track when cornering, I knew I needed to remake the whole thing. Then I just did the upper faring because carbon fiber is the coolest thing in the world 😄
Here are some links for the products I used in this video:
2X2 3k Twill Carbon Fiber Rolls
amzn.to/4fsdyiE
2x2 12k Heavy Duty Carbon Fiber Rolls
amzn.to/4fnhqS6
Slim 1” Header Wrap
amzn.to/4d0cxwR
Inner Fairing Heat Shield
amzn.to/3SsZATW
If working with carbon fiber and other composites interest you as much as it does me, you might want to check out these other creators who have taught me a lot within the past few years:
⁠‪@xylafoxlin‬
⁠‪@StreetBandito‬
⁠‪@BuilderCreator‬
Beginner Motorcycle
Affordable Motorcycle
#motorcycle #racing #carbonfiber

Опубликовано:

11 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 16

@thegolfdude 29 дней назад

The close up of the welds had me for a minute, not gonna lie

@Extra-Medium-Skills 28 дней назад

Neither confirmed nor denied 😁

@filipporolandi9529 Месяц назад

I think you could use expanding foam to fill the alluminum cage, than shape it. Doing this you could make the curves right and avoid pockets of air and resin having a nice surface to lay it on. Other than that, Great work!!

@Extra-Medium-Skills Месяц назад

Great idea! I’ve not used expanding foam in a project yet, I’ll put it in my to-try list 👍🏽😁👍🏽

@HadleyUnited Месяц назад

my favorite bit in these series is "heres a close up of my welds"

@Extra-Medium-Skills Месяц назад

…not to brag, but y’know 😉

@jamesdangercarpenter Месяц назад

Really enjoyed this, keep up the good work 😄

@Extra-Medium-Skills Месяц назад

Thank you! 😁

@RyanCorbett-d5x 26 дней назад

Cheap kitchen scales would be more accurate for the resin mixing and not just a single use tool (y), nice video bro

@Extra-Medium-Skills 26 дней назад

Good point @ryancorbett-d5x! For this particular epoxy, I use volumetric measurements. The manufacturer suggests volume bc the density of each part varies. But totally true that epoxies can be weighed very accurately with cheap scales! Great budget hack 👍🏽👍🏽

@viboldsok 25 дней назад

Not perfect but better yet not bad at all. Can see why this channels call extra medium. 😂

@Extra-Medium-Skills 23 дня назад

Thanks haha! Always improving… but enjoying every minute

@pictie Месяц назад

best option for carbon is a vacuum system thair rather cheep to get the components a pump from harber fraght you want the expensiveness one the cheep one is know to exsplode and a chamber to catch resin run off " easaly made from a pice of shedual 10 4 inch pvc pipe 12 inch pice shuld suit just fine matching end caps and two thread in barbs that fight 1/4 vacum hose one in from the work pice and the other out to the pump . i only say this becaous carbon is at is strongest with a one part carbon to one part resin composition and you get a sanifigently beter surface finish and way less issues working as long as your molds clean and buffed out to a glossie finish that is . nice job ither way most defitly a funtional part keep taking big bights one project at a time if you keep taking them you will surprise your self .

@Extra-Medium-Skills Месяц назад

Thanks so much! I agree vacuuming and a real mold would be the best! I aim to do a higher quality vacuum part sometime in the winter. Lots of good instructional videos out there. You made great points! Stayed tuned my friend!