Change DPF pressure sensor or hoses on K9K 1.5 dci engine 

Hi, would this sensor fail or the pipes being broken throw a pf1400 code? Thanks and what would symptoms be?

Best video ever! Thank you ,my friend! If oneday you came by my house will have a beer!

Well done and very informative, regards

I have a DF016 EGR Command Circuit,Short-Circuit To +12v Active and a DF089 Inlet Manifold Pressure Sensor Circuit,Permanent Low Level Active on a Renault kangoo 1.5 DCI the car won't start and the glow plug light won't go off when I put in switch I don't understand is the car in limp mode what can I do to fix it I doesn't have injector pulse

Excellent walk through. Just done mine and removed the wiper skuttle panel which makes all the difference. Thanks for taking the time and explaining in english subtitles.

I am doing the same job now ,on my mk3 scenic, what a painfully awful job for one rubbish quality pipe , reaunlt haven't even botherd to upgrade the pipe , which they know is a common fault on all models ofthe1.5 DCI engine, shocking really, and the cost in the UK for the two small pipe s is £65.00 totally a true rip off, Thanks for your very helpful video, very much appreciated.

Merci, même si mon Captur est différent cela m'a aidé. Tu es un bon gars.

thanks for the perfect guide line, normally you need a 5 year old child to do this with small hands 🙂

Thank you for your explanation. It realiseren helps me to fix my car

Thank you for the video. Good explanation.

Very clear and informative.. thank you...

Hi, if you blow sone air wihw mouth on these hoses, its blocked or not ?

Brilliant video thanks

Helped a lot!!

Merhaba Aracım Megane 3 15 dci 2012 Arıza kodu P0471 ve P0473 Bu parçamı arızalı aceba bilginiz varmı. Aracım iyi çekmiyor hızlanmıyor. Şimdiden Teşekkür ederim.

Thank you for a excellent video. I don't think i will have made it happen with out

Did this job today on a Megane 3 1,5 dCi 110 hk 2013. I removed the wiperarms (marked alignment with tape on windscreen), the two rain scuttle-pieces and the air hose from the O2-sensor/air box. Early on I took some pics of the enginebay just to have some guidance on how to reassemble. Recommend that you do the same. Then unclipped all contacts obstructing and was then able to reach down behind the engine and could even see what I was doing. First dismantled the pressure sensor (one nut) to reach the backside of its contact and unclipped this one. Then pushed the pressure sensor against the torpedo wall and could see the two bottom clips which I moved upwards with pliers. Bit tricky. Now I could remove the unit with hoses attatched. My short one was broken, the long one intact. Got new hoses from Nissan (they use the same engine in some models) with the numbers described in this RU-vid-clip. The short hose was exactly the same as in my car but the new long green hose had a too large large diameter at the end facing the sensor. Didn’t stay in place so just changed the broken one. When reassabling I first clipped the sensor contact back in and then tightened the nut to hold the sensor in place. Then with the top clips in place over hoses I slid the hoses bottom ends of over the pressure pipes below. I succeeded in sliding the clip down on the short hose but not on the long one so used a hose tightener with bolt instead. Lots of contacts to re-clip and the rest is pretty obvious.

Great helped alot mine was a hex key bolt,and took the fuel filter and carrier out many thanks 😊.

Fixade tjejpolarens bil tack vare din video. Riktigt bra 5/5 😁👍

I just did mine, all I removed was the air intake from the air box and the EGR valve, gave me plenty of space, relatively fiddly but straight forward, hardest part was getting the broken half of the pipe off the bottom but it comes off eventually with a bit of fidgeting and patience, I got some generic 6mm high temp hose from a motor factors. Just want to add that I've never worked on cars before and found it fairly straight forward, took me about an hour in total including time it took to cut new pipe to length, also if cutting pipe to length ild advise to take 1 pipe off the sensor at a time and cut it to length as the pipes are different lengths

Omg I done mine in 2o min with a mirror no need to take the car to bits 🎉🎉

Hi which hose is going before the dpf and which after ?

Jag har en Renault Kangoo 2011 med felkoden P2002 och vad jag läst mig är att det ofta är en brusten slang som orsakar detta. Antar att det är dessa.

Will this help fix p0299 error code?? It’s doing my head in 😢

remove the lhs 3 engine mounting bolts and slide/push the engine forward 30mm, makes all the difference to reaching in to grip the pipes.

DACIA duster with cdi 1.5 renult engine is the same?

very good, thank u

I did this with Megane III 110 Hp 2014. I did not remove the wiperarms. It was possible to operate with mirror and light. There is no need to remove the battery in 2014 Megane. only the air hose has to be removed. As MN told the other hose was not compatible with K9K 636 motor. The shorter one seems to be the one that breaks. The other one was OK, no need to change that one.

Hi has anyone got the link to the pressure sensor?

I’ve got same fault code p1453 but it’s says fuel tank pressure relief valve fault Dacia Duster 1.5 dci . Notice the connector on top of filter was melted a bit so I’ve replaced it but still same code and fault . Where is fuel tank pressure relief valve???? Any help much appreciated

hi Jola, when will you change timing belt ? I am looking forward that. My Megane 4 at 87.000 Km, I have to change timin belt and water pump.

¿Is it dangerous drive with the black pipe broken?

Bra jobbat och bra video! har en Renault Megane och får felkod P2454 vilket tyder på lågt tryck i avgastrycksensorn. tänkte beställa en ny sensor. men kan du tipsa mig var man köper slangarna till sensorn. Var beställde /köpte du dina slangar? tacksam för svar,

Hello . Good job bro ! Let Me know please if The location for The sensor is The same for Renault Megane 3 , 2013 1.5dci 110hp . Thanks

WHAT. i couldnt hear ya

Any English subtitles?

Great video. Thank you!

If you remove the raintrench instead of the airbox, you will work easier.

636 мотор, на 836 по другому