Cheap 12 Inch Brushless Spal Fans 

Overall size of the fan is 16.5 x 26.5 x 3.5 with some wings that stick out you could use or just cut off.

05:12 I grabbed two 10 inch pusher fans off a 2010 Land Rover SUV for $17 each at U-Pull and put them in front of my 1990 F150 AC condenser and now my AC went from 65 F in stop and go traffic with 96 F ambient to 47 F out the vents....Salvage yard OEM parts are far better and cheaper than new on-line knockoff garbage...great video!!

Just found a pair at the U-pull out of a Volt and remembered having in my 14. Spal are my go to like a McIntosh receiver. Signal wire sealed brushless and the Spal housing for a fraction! Now I have my rugged set for the continuous solenoid set up and one to run at my exact needs. Great right up bro, not many know.

Hey brother I just want to thank you from the bottom of my heart .I figured the cooling fans they work amazing . God bless thank for all the information

Love those fans, I used the Z06 fan on my last ls swap and I'm using the big dog 19" fan in my latest swap. BEAST

Dude! This is the bee's knees! Thanks for the info for the Holley/PWM crew.

Like the info. Surprised no one mentioned the thumbnail says burshless and not brushless.

Fantastic ‼️ those fans move some serious air. That should make a big difference cooling the boom

Awesome. I just hooked some dodge intrepid fans up to my ls swap s10

Great information I have been wondering how to do this

Good work dude!

Awesome vid. I was looking for something like this for my build I called at my local junkyard which is hour and a half away and order me some pick them up Saturday. Thanks

Thanks for the info.

Great work, thanks for the information

Nice! So you only use one of the outputs from the Holley. If my F150 fans ever die I may go with a set up like this.

Getter done bro great fan set up

If the controller failed you could probably open it and solder on a brushless motor controller but I don't know about that input signal

Great video!

Bad ass. The signal wire makes me wonder if there’s a built in mossfet driver Since brushless motors run on ac. Thanks for the tip 🤙

What a kickass setup

For fan power what size fuse are you using? Great set of videos. They have been very helpful

Awesome tip! just one quick question, do you know if the PWM signal has to be a positive or negative signal (PWM to ground or 5V positive?) Thanks!

I guess spal is a brand maybe that makes them for OEMs or something but just brushless motor is the important part

Nice 👍. I’ll be stealing this 😁

OEM spal...nice!!

Pretty good no-nonsense DIY video. I did something similar with a set of Ford 12" dual fans out of a 2002 Ford Contour. Ford uses Bosch motors but they are not brushless. I have them in a custom shroud, cut away all the excess material just saved some sections for flanges. Don't think they are as powerful as the SPALs you're using. I'm trying to cool a 461 BBC with a Holley double pumper using an external PWM. I want to know how you can control these fans, is there an aftermarket controller that will work with brushless fans? What about temp sensor? Gonna check out your page and see if you have the next steps. How big is the actual shroud section without the side wings?

Thanks for your video. How many Hz need the pwm controller to adjust the velocity?

What fans are these from

Is this only for the GM genuine fan assembly that they are SPAL? I'm seeing them as discontinued but TYC, Spectra, and Murray all make aftermarket replacements

Thank you when you finish the table please do another video how too..

Great info. What fan would you recommend for 65 chevy c10? I currently run 14 in generic brand and looking to upgrade. My truck is just a 350 small block with mild cam abd headers. Would greatly appreciate your input.

great job, so no relays are needed with this setup?

Do you have the dimensions for that fan setup? I have a small Radiator and wonder if they will fit.

Would these fans be a good choice for my setup? 70 Chevelle LS swapped, twin turbo, air to air blocking the front of the radiator and I’m currently putting air conditioning on the car and the condenser will be between the radiator and intercooler. Super budget build I need a good brushless junkyard find the Holley can control

Hello I have a 1987 mercedes 300d with the 3.L turbo diesel. Currently it has a clutch fan that i want to swap out for electric fan. The cooling surface on my radiator is 19x29. You have any suggestions for a fan I can use. I cant use a fan like what you have because there is no computer So I would need to run relays from temp switch. I live in the boise area which is often 100deg and up. And if you run ac the motor runs hotter than I like. Any suggestions would be greatly appreciated. Thanks for your time. Robert

is there anyway to get them to come on with the a/c

Does a gen 3 ecu control them or signal on? Or am I looking at an aftermarket controller? Any ideas?

👍

What is start amperage and running amperage full speed?

Would the 2016 volt fans work the same?

Do you have a link to the fans ?

👍👍

how many watts or amperage each are these chevy volt 12 inch fan ???? C7 Corvette 600watts ,,what diameter ??

need 10 inch

Do you have the connector part number?

🐓

get a couple sets make a hovercraft

Are you PWM negative or PWM positive?

You can all follow this video and go try to source you those fans from a yard....or you can check this video out and go grab you a Mercedes fan that will pretty much destroy both these fans ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-kGylouOxVL0.html

I don't do junk yard race cars sorrt

What fans are these from