No video :(

Complete Guide on How to Remove/ Install a Nissan 300zx Power Steering Rack

Подписаться 9 тыс.

Просмотров 13 тыс.

50% 1

After a long season with my Nissan 300zx Drift Car I have noticed that my power steering rack had a massive amount of play due to non exsisten bushings. So for my z32 I was able to score a power steering rack off of Mark. So I used it to my advantage to swap a new rack and the bushings at the same time! I hope this tutorial helps you out. Remember to like and subscribe!
Parts used in this video:
-Energy Suspension Bushings:
shop.advanceau...

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 34

@bennyhinton5562 Год назад

Just did my rack without dropping subframe. Just remove hardline located on top of rack. Rack will slide right out. Take hard line off new rack and slide in. Mount it down with brackets and reattach hardline. No worrying about subframe nor motor mounts.

@findalefinnie 2 месяца назад

Same here. Worked for me.

@royels3016 3 года назад

I had to replace my rack and pinion recently, thank god for this video I had no clue how I was gonna do it until now, good job bro keep it up 🤙🏼

@ZBruhzchannel 3 года назад

Thats great! I'm happy you found this helpful ☺

@kojimasuda 4 года назад

Thanks to you, just had my bushings done. It is soooo much easier with the engine out. Keep up with the good videos. They have helped me to save a lot of work and time. Tks!

@ZBruhzchannel 4 года назад

Awesome! Thanks for the support

@codyc5787 4 года назад

Channels like this really make me want to get into grassroots drifting. Subbed

@ZBruhzchannel 4 года назад

Awesome! Thank you!

@stevewalker4964 2 года назад

Good video. Definitely should've done this before I did the LS swap in mine. Lessons learned. I'll be doing mine this weekend.

@sailingblacklotus 4 года назад

Just removed my steering rack thanks to the video. THANK YOU. I couldn't remove the outer tie rods from the knuckle as per video however. I had to use a pickle fork. Chowdered up the ball joint boots but that's the only way I could do it. I also broke one of my studs off my tension rod passenger side lol...

@reygm3639 4 года назад

Awesome man that's a big help i recently bought a 300zx I know in the future I'm going to do that 😬💯

@alosha4321 11 месяцев назад

Great vid. I dont need to do this but good to know in case i do

@stone726bl Год назад

Good job....This will help..I have to do mine too👍🤓

@JunieMunoz-qj5ug Год назад

Hi, thanks for ur channel. I can’t afford to pay someone to work on my Z. I get my work done thru ur channel. I’m working on my oil pan and im now on the pan now. I dropped the subframe. I removed most of the 10mm bold and stopped for the day and left the corners. Am I able to remove the bolts driver side. Where the oil feed, the bracket where 1 bolt goes thru the Tran house. I hope my clutch doesn’t come out?

@ghostsmoke11 4 года назад

1:19 You have your flag hanging wrong. The union is supposed to be facing to the upper left when it is hung in this orientation.

@zeda9253 Год назад

This might be a dumb question but how important is the power steering rack gear cap? Would it be dumb if I drove without it?

@ZBruhzchannel 11 месяцев назад

I'd say it's important to be honest

@noahhh111 4 года назад

Thanks man perfect fucking timing with this video

@ZBruhzchannel 4 года назад

No problem!

@megashem101 4 года назад

Im looking for a steering rack for a right hand drive 300zx TT 94. Any recommended sites?

@ZBruhzchannel 4 года назад

That may be tough, I would contact z1 motorsports or concept z performance to see what they can get. Or a possible JDM warehouse

@megashem101 4 года назад

@@ZBruhzchannel thank you. Keep up the good content.

@ZBruhzchannel 4 года назад

@@megashem101 thank you!

@kyricwallace9843 4 года назад

Good luck! If you have the old one off your car concept z or z1 will rebuild it and send it back

@ZBruhzchannel 4 года назад

@@kyricwallace9843 that was the plan!

@MatSnake5000 4 года назад

i can’t figure out how to get the inner tie rods off of the old rack, any recommendations?

@ZBruhzchannel 4 года назад

They are probably loctite in, do you have the rack in or out of the car?

@MatSnake5000 4 года назад

Z-Bruhz it is out of the car

@ZBruhzchannel 4 года назад

@@MatSnake5000 if you have a vice I would put it in that, or what andrew and I did was we had one person step on it and the other work the wrench

@smknblnts 2 года назад

Is the NA rack same as TT ?

@ZBruhzchannel 2 года назад

No. I believe the tt has a little less steering rotation when compared to the NA. NA has 2 3/4 rotation to each side and tt has 2 1/2. I would do some research on twin turbo.net