Hi Lads, first off I apologise for the audio and video quality in some areas, i wasnt using my normal camera so therefore it wasnt as good quality. Anyways sit back and enjoy this longer video!
After watching this, I immediately went online and ordered heated mirrors to replace. Finally received it a week later. Impatiently I went straight to pull off the old mirror. Lo and behold, There were already heated mirrors on the car, I never knew because there is no separate button to operate them. They work with the rear defroster button. 22 euro down the drain. :) Well not really. I replaced them with the new ones anyway. :D
Hey! Hope you're keeping well and safe. Been binge watching your videos, even though I don't own a Corsa D. Just nice to see how things are done. You are certainly knowledgeable and your Corsa must be the most maintained out there!
Hi Tom, Thanx for the amazingly instructing video! I've just completed this project and I must say the mirrors get nicely warm 😍 Putting the door back on was indeed a nightmare for one person 😅 Anyways, cheers again for your videos. I love them! Greets, John
Eres MUY GRANDE TÍO..gracias por enseñarnos tantas cosas del corsa D..lo explicas muy bien y gracias por subir vídeos gracias a ti nos ahorramos mucho dinero, con toda la información y conocimientos que tienes....
Your crimping job was unfortunately not 100 % correct. The seal/gasket for the connector around the cable has to be crimped with the cable onto the connector. Each crimp contact has two different sized tabs which grabs the outer cable insulation and the other one grabs the striped copper cable for conducting the current. The round seal/gasket should be crimped onto the bigger tab which would hold the outer cable insulation when you do not use a seal/gasket. Anyway nice job!! I will do the same thing on my corsa d in the summer. Also I will fitting heated seats, dimming mirror, rain sensor, new interior lamp, heated steering wheel, maybe rear speakers, and pre wiring fog lights, park pilot... Everything as original as possible... Thinking about filming videos about it in German.
Hi Tom Merci pour ta vidéo Very useful I don't have your strenght I will cut the old wires and connect them to the new wing mirror outside I will hide the quick connectors in the cover French guys are a little bit lazzy ;)
Hi Tom, Would love you to do a front footwell lights tutorial video and possibly puddle lights at the same time buddy. Just a thought for your next project...... Sy.
Hello Tom, I watch your videos and are very very helpful , you do a nice job. I just finish install on my corsa D front fog lights and cruise control. The only thing wich i can’t do it with Opcom is to do the setup , apparently don’t show me all that options when try to change variant configuration. The cruise control i setup already on engine module , but i can’t on Body and Instrument. Were do you think can be the problem? Maybe Opcom? Thanks
Hi Tom, one of the bulbs in the foot well of my Corsa D has gone out, along with one behind the fan dial on the centre console below the radio, do you know where I can purchase replacement bulbs?
Few places you can buy them really, here is the title from Ebay I found : VAUXHALL CORSA D HEATER CONTROL ILLUMINATION BULB (93190474) GENUINE NEW 07-14
Merhaba Türkiye den yazıyorum 2008 Corsa d 13 .aracım eletrikli aynalarım çalışmıyor sigortaların sağlam kontrol düğmem sağlam .konnektör den olabilirmi sizden bilgi almak istiyorum arıza nerede olabilir
Great video, how do I go about getting them to work if I have the factory heated wingmirrors? I installed them hoping it would be plug and play but they dont work unfortunately. Thanks
@@TomsDriveway what I meant was I have bought heated mirrors and fitted them, the wiring harness of the doors matches up to that of the mirrors etc but it doesnt come on with the rear window? Thanks
Do you know how can i disable the seat belt chime? It activates even if i have the seatbelt on and it's quite annoying at some times when travelling long distances because it activates at random times. Can it be disabled in opcom?