Your camera work is exceptional and I'm off to replace my impeller pins! Unfortunately my craftsman came with hardened rolled steel pins that rusted out. Seems as if part of the 2 pins rusted into the shaft so I have no way to just replace the pins without drilling the holes clean. You have explicitly showed me how to separate the snow blower into 2 parts so now I can work the shaft to connect the impeller back onto the shaft! Thank you!!
Same, virtually exact, issue here in Sweden. Different brand name, assembled in US. Your video helped loads. Haven't got the right tools, but some stone will do for 'anvil', some heat and a carpenters hammer. 'Elbow grease'. And I have the time, so why not! Thanks Fixer Merlin!!!
Yellow things are augers and they fit into the auger housing. Yep got the same issue after catching a bundle of newspapers in a snowdrift. Stalled the engine and bent one of the tines on the impeller. Thanks for sharing your great video.
Great video of your repair. I recently picked up a 25 year old, 8.5, 26" craftsman for $50. Hadn't run it 2+ years. Cleaned the carb and got it running, but when I engaged the auger, the impeller was making a big noise and bouncing in and out. Seperated the housing from the engine and found that 2 of the 4 impeller blades were bent, as well as the auger blades rusted solid to the shaft. The steel they used 30 years ago in these machines is thicker that nowdays. Applied a 50/50 mixture of acetone/ATF to the impeller shaft as well as the auger. Took a few days of soaking and a couple of 18" pipe wrenches and I was able to remove everything off the shafts. If I was still working, I would use the company's hydraulic press and maybe even weld it to our welding table. That said, one option I might use is add a 1/8th" spacer between the impeller shaft and the housing, quick fix, $1 for a 1/8th" thick, 3/4" hole washer to keep the impeller from hitting the housing.
@FixerMerlin doesn't really "remove" it however it does break it down. It did however break the bond between the auger shaft and the auger. The machine I was working on didn't have and grease zero fittings and most likely had never been serviced, greased or taken apart since it was made. Patience and drops of the ATF/acetone 2x daily worked for me👍Used 80 grit sandpaper on the shaft after and I removed the auger blades and will install zerk fittings on the auger shaft before I put it back together
my impeller just got bent yesterday... no where nearvas badly as yours ive got a Poulan... but it looks identical to your craftsman.. .. thanks for the vid
Haha thanks! Cold working light steel like that takes patience but I’m really happy with how it turned out. Very glad it wasn’t something more costly and time consuming.
word of advice ....take that chute brush off the machine and leave it in the shed or garage. When you run over that and get it jammed in the auger it isn't good !!
I have the same problem with my Troy-Built impeller. A friend sent me a link to this video. I can't believe there's not more videos on this. Anyway, thanks
Interesting. I have had my MTD snowblower since new in 1997. It has vaporized newspapers, chewed up extension cords and slung rocks everywhere. No damage..not even a sheer pin. Lucky I guess.
That tool box is for extra shear pins, wrenches, etc. Not a common feature anymore as most people just aren't capable of doing their own maintenance nowadays.
They're probably going to get me for $300 + pickup/delivery charge. You made it look simple. I wonder if they're going to straighten the impeller and charge me for new.
Jeez man sorry to hear that.. Could end up costing a good part of a new machine? Next time you'll know exactly what to do and be back plowing snow in about an hour!
@@FixerMerlin I wish I could do more to thank you! Merry Christmas. We've been getting a ton of snow and I bent my impeller the other night. I don't have a garage but we got a little sun this morning and I was able to straighten mine through the chute window! Normally I'd separate it like you did but I'm in a pinch and my house is buried lol thanks again!
@@TrillMurray just like and subscribe! Knowing that people like what they are watching is all the thanks I ever need! I hit a stone again this year and was also able to repair minor damage using a long punch without opening it up
Haha actually I think I got off really easy! It sounded so much worse than it was! I’ve heard tons of stories about gearboxes blowing up, thankfully it wasn’t actually too serious!
I just did a simplicity 2 of 4 severly bent other 2 bent some. Had to cut welds on 2 about a 8"" piece of railway rail for dolly big hammer got it back in place. Weld it fixed. Had to sacrifice bearing with torch to get it apart. Someone else tried to fix it but failed.
@@FixerMerlin I got it all taken apart but hit a little snag when it came to removing the impeller from the shaft. In your video, at 8:29 you were able to simply slide it off away from the augers. Mine was apparently assembled from the other direction and would not come off that way. I just put the whole thing in the bench vise and managed to straighten the bend parts with a large pipe wrench and a smaller adjustable wrench. I just need to re-assemble it all and give it a test but I'm pretty sure it will work fine now. Thanks for your video, it was helpful to see the process before taking it on myself.
@@ridefastjumphigh420 way to go man! You probably saved yourself 2 or 300 shop charges at least to get that fixed and who knows how long until you would get it back
I have same exact one and my gearbox housing blew a hole on both sides from the steel roll pin breaking in half and digging its way out of the housing with the centrifical force. Just a heads up.
Towel got caught in my impeller and the engine stopped. Spent a long time trying to cut out the towel but finally gave up when I realized the motor itself will no longer start anyway. Did I break a hard-to-access part in motor? I have replaced shear pins in auger but this seems a more serious repair, do you agree?
had same problem too, thanks. But..... could you change out the 2 bolts that hold the impeller to the shaft for sheer pins so it would give if another rock got jammed in there? Just askin.....
@5:44 there is a small hole, maybe 1/4? And a bolt should go through the impeller and the shaft. If it sheared off flush it might be hard to see and you might need to drive it out with a punch?
@@FixerMerlin Is it supposed to be a shear bolt? I guess that would have prevented the deformation of the impeller blade and would have left you with an easy fix. Are you the original owner?
@@wryanddry2266 I bought it new so I’m assuming if there was supposed to be a shear bolt there they would have used one, but it doesn’t seem to be. The augers both have shear bolts I’ve replaced a handful of times.
@@FixerMerlin I would be inclined to use a couple shear bolts there, if they seem to fit okay. If they shear too easily, you can reach them easily by removing the base of the chute.
My thought exactly, get it running and working again. I’ve heard about adding the rubber pads but not sure what the benefit is other than adding a seal where they contact and making the blades more efficient?
That looks like a real weak design. All my blowers have braces behind each impeller blade to reinforce it from bending. I can run small branches thru mine without bending anything. If I were you I would weld some small supports behind each blade on that impeller to strengthen it.
Ya it’s crazy to see how cheaply made they are, reinforcing it could definitely help but I do t think it was designed to be used as hard as I push it..
The bearing that sits in the housing between the auger pulley and the impeller might be damaged or worn out. If it has too much play the shaft will not allow the belt to maintain proper tension and will probably slip off the pulleys.
Really not sure, engine oil? or gear oil? If you clean it off well you should be able to see where its coming from when it is running and heats up? Anyways good luck!
@@FixerMerlin Thanks Well that’s what I am not sure It was working fine week ago today was blowing snow fine all of a sudden I wouldn’t drive no more or back up. I put it away like that yesterday when I went to look at it and was oil all over the floor comes from around motors Frame
Id start by checking the engine oil level, if it’s empty don’t run it! Could be gear oil? I’d check that the drain plugs are secure, not sure but maybe some how you could have cracked a housing or unseated a gasket? Hopefully it’s nothing too serious..