Creality CR Touch - Auto Bed Leveling Kit - Ender 3 V2

Подписаться 235 тыс.

Просмотров 192 тыс.

50% 1

Amazon Links
Buy it here: geni.us/9nGmb
Recommended: geni.us/JustVlads
www.crealitycloud.com/softwar...
Stripes stl: thingiverse.com/thing:5174552
Creality CR Touch Auto Bed Leveling Sensor Kit. Creality Official Specially Designed for Ender 3 v2/ Ender 3/ Ender 3 Pro/Ender 5/Ender 5pro/CR10 for 32 Bit V4.2.2/V4.2.7 Mainboard 3D Printer
Easy to Install and Use
The kit contains 3 different mounting brackets and extension cords. You can easily install
Product Durability
Creality CR Touch is specially designed for 3d bed leveling for Creality 3d printers. Compared with BL Touch, it has stable quality, long service life, and can be reused more than 100,000 times.
Creality ideal companion
CR Touch works for Ender3 v2/Ender3/Ender3s/Ender3 Pro/Ender 3 Max/Ender5/Ender5 Pro/Ender5 s/ CR 10 with 32 bit motherboard.(3d printer accessory with the best experience)
Strong compatibility
CR Touch 3d printer auto leveling,Compatible with PEI / sticker bed / glass bed / metal bed
As an Amazon Associate I earn from qualifying purchases
My website: www.justvlads.com/

Наука

Опубликовано:

14 апр 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 274

@JustVlads 2 года назад

New Channel: www.youtube.com/@Just_Print CR Touch: geni.us/9nGmb Recommended: geni.us/JustVlads

@TheChromePoet 2 года назад

Please tell me this, can't you just replace the springs with something solid now that you have automatic bed leveling. Doesn't make sense to use springs and risk the bed shifting over time.

@eventhorizon492 Год назад

Dude, I’ve been having problems with mine since install because all the tutorials wouldn’t explain what they were doing. Your a life-saver

@andrewhofmann5453 2 года назад

I just installed mine. I would recommend to viewers that you take the extra time to fish the data cable through the flexi-duct, it just adds that OEM feel.

@danielschmidt1990 2 года назад

Any good cable management just gets me off :P love it

@bobbylim1971 2 года назад

Yeah i did that. Was contemplating for 5 minutes if i should do that or not. End up doing it and it felt smart and clean. No regrets.

@mve9924 2 года назад

for the newbs....when you slide the duct back, it expands in size quite a bit

@couryrussell7653 Год назад

I took your advice and definitely appreciate it!

@H31MU7 Год назад

I read this comment after cable tying on the outside it the whole way down to the board... ...yeah, it does look way better fed through the duct.

@joygibson6623 Год назад

I had to come back to level and fine tune my settings. Thank you! I appreciate you showing the whole process. It's seems all good now! Ty again and again!

@GabiFodorrasRO Год назад

Din câte tutoriale am urmărit pe RU-vid acesta este cel mai explicit tutorial Multe salutări din România !

@grasug8550 Год назад

My Ender 3 V2 Neo arrived yesterday - I've never used a 3D printer and oh boy are the instructions insufficient! First successful print I've managed to do is thanks to your advice, thanks very much, I appreciate it!!!!

@shamefulexistence 2 года назад

FYI: The firmware you selected is for adding the auto leveling sensor AND a filament runout sensor. (They make a filament runout sensor that will stop printing if your filament runs out so you can load filament and resume printing).

@summerofsteroids Год назад

@Jane Pimentel Did you ever figure this out?

@LowellBrillante 2 года назад

@Just Vlad thank you so much. Huge help. You got a great voice and tone for podcasting too

@KunaiMelee 7 месяцев назад

2 months trying to figure this out... you helped me so much friend. thank you! cheers!

@wfs1965 11 месяцев назад

your instructions are detailed and thorough,. I used ur vid to build my first printer, the voxelab aquila, thnx ur the best. Glad I found this vid for my Ender 3 V2, a lot easier and more detailed than the others as well, thnx again!

@user-rq6rx5cp7i 2 года назад

Спасибо, мужик! По видосу легче настраивать, чем по инструкции на крохотной бумажке из коробки :)

@burgertim7878 7 месяцев назад

My BL touch port had hot glue all over it, thanks Creality.

@stephenruvalcaba4680 2 года назад

so many step and so well explained!!!! thank you so much! even on my normal LCD monitor, i managed to get my cr touch to work! thanks a bunch!

@bgcm1995 Год назад

How'd you download the file? I have an HP and I keep getting a Adobe acrobat file and it won't download.

@mtschutte18 2 года назад

Was thinking about it yesterday actually and I have an ender 3 V2, so it was perfect timing for this video, ended buying this auto leveler cause the others are plastic and I want the durability.

@jasonlopez5064 Год назад

Thanks dude! Just installed mine following this video!

@santiagodamasco Год назад

Thank you!!!! Finally a good and easy explanation of the process.

@EldrinOS Год назад

Hey man, just wanted to say thanks for this one. Was having a hell of a time trying to figure out how to best configure my offset but this made it painless.

@bgcm1995 Год назад

How'd you download the file? I have an HP and I keep getting a Adobe acrobat file and it won't download

@BavarianLord29 2 года назад

good job. Thanks to you I was able to install everything today!

@edsonx2001 2 года назад

Thank you! This is a good resource for cr-touch leveling 👍

@mcdouble_2475 2 года назад

Love your videos they are so helpful. 👍👍 keep up the good work!

@tammykillian8134 Год назад

I’m having a heck of a time getting mine to level properly. Both with and without the CR Touch

@hufftechsolutions7903 Год назад

Make sure the wheels on the bed are tight. If they aren't, you'll never get it level

@CCR30 2 года назад

Thank you very much for this. It helped me a lot.👍👍

@dylanaalderink1430 2 года назад

This guy has saved me twice tonight alone. Great Videos!!!!

@Kimberlysocialmgmt Год назад

This video helped me figure it out after hoursssss 😅 thank you! I just had issues finding the download page but finally got to where he was at. Only issue was when I put in printer it was in Chinese 🥴

@pianoplayer1224. 9 месяцев назад

Please can you send me the link to the page and which download u used? Thanks

@lpzshaun Год назад

This video was extremely helpful thank you

@thespaundrummer1176 Год назад

Vlad, nice video, One thing... The G29 code needs to be on a a separate line following the G28 command.I entered it as you demonstrated, but the CL-Touch only checked the center point. After moving the G29 to a separate line, it now checks 9 points.

@KaiLucasZachary 7 месяцев назад

Interesting. The instructions that come with the thing very literally tell you to put it all as one "G28G29" the way he did in this video.

@Zack-gs2xt 2 года назад

finaly a ender video

@bgcm1995 Год назад

Everyone please remember that once you open the bottom part, to check your main board number since you need afterwards to install the firmware!!!! I put everything together, took the bottom off to connect the wire and now have to take it off again to check the main board number.

@ekalbtratloc8107 Год назад

I was having trouble with the firmware side of this for my ender 3 max, but this video was absolutely perfect! ... unfortunately I did somehow manage to install what I believe is Chinese version(as I don't recognize any Kanji and it definitely isn't English😂). So I'll have to have to quickly fix that, but that was a me problem anyway. Thanks 👍

@ginoantenucci6424 Год назад

Important note you have to remove the z limit switch as the cr touch acts like the z limit switch now also you should install the firmware that says just the bl touch not filament runout sensor

@miriamwong4200 Год назад

What happens if you don't remove it? I'm new to this and don't want to mess anything up

@ginoantenucci6424 Год назад

@@miriamwong4200 according to the manual it says it won’t destroy your machine but It is recommended what happens is that you unplug the z limit switch so it would make sense to remove it if you don’t it has an unlikely chance to try to move the z down and the z switch is stoping it by force which is not good for your stepper motors and since the z switch is unplugged it won’t stop the z gantry

@SpikeCooks 11 месяцев назад

Hiya, hoping you could answer my question as your reply seems to be kinda what I'm looking for. I feel like I'm having lots of trouble manually adjusting the z height to get the best print, if I got this product, would that mean I wouldn't need to fiddle around with the cogs below the bed to adjust the height?

@ginoantenucci6424 11 месяцев назад

@@SpikeCooks no you would still have to do the same fiddling just after your done fiddling you won’t have to manually level a lot the you can just use the automatic level and that should avoid manually leveling for a good amount of time but note that once in a blue moon you should re level your bed manually to make sure you get the best quality prints (I manually leveled it 6 months ago and it is still leveled good I normally auto level it after every print but if it is a not really important part and you don’t mind so much if it is not the best I sometimes skip auto leveling the bed)

@grahamtimms70 Год назад

Just fitted this hotend and fans on my Geetech Prusa pro with a bowden cable.

@chengkuangan1138 2 года назад

Nice video, thank you for sharing

@holgerst3607 2 года назад

nice video love your content

@calebkincaid3031 2 года назад

Love your videos

@daurham Год назад

If you can't find your firmware version: You can find it on your motherboard, when you open it up. Mine said "4.2.2" just under the creality logo, near the center. ( Ender 3 Pro )

@nathancogbill8429 2 года назад

Please do a video on the enter 3 s1, but either way love ur vids

@cascadesouthernmodeltrains7547 2 года назад

I fed my cable through the webbing to make it all look like it was made that way. It wasn't too hard to do.

@paulherman5198 Год назад

Gonna have to order me one. Already got Jyers UI for mine. Waiting on my 4.2.7 board to be dropped off.

@paulherman5198 Год назад

I would also suggest some Silicone bed spacers. Then you dont have to deal with the springs

@josephjolly1957 2 года назад

Great video.👍

@alesculek182 7 месяцев назад

Definitely install the cable from motherboard to the sensor via the existing flexi cover. Also Z stop should be removed. Edit: check also your motherboard version when you open the cover and write it down somewhere, I had to open it twice.

@thedogporch Год назад

Thank you

@leektah354 Год назад

You didn't mention removing the Z axis limit switch which is no longer needed.

@J2XGaming Год назад

Great video no kap ✅

@onlineshaman Год назад

You forgot to unplug the Z switch, it's not needed anymore and they recommend it to be removed! ✌🏻

@TheGR3ATOne 2 года назад

Great tutorial, only problem I have is my firmware change the language to chinese. And I tried multiple different versions, all in CHINESE. Lol thank god I can understand the letter A in a box means something about languages.

@magicalcupcakenutz8153 Год назад

@KILBILL6331 blessed thank you so much

@mbladeakita9173 2 года назад

One of the things they don't tell you is you have to rename the .bin file or else it won't work. You are all welcome!

@greenshark6899 Год назад

hi, rename it? Thank you

@kenmasters402 Год назад

@@greenshark6899 rename to firmware.bin i just figured this out

@Byrkster Год назад

Wait, those mounting holes at 3:28 were not there at the beginning 0:20, did you get a replacement bracket? If so where did you get it. My Ender 3 v2 does have those mounting holes. I was just curious as to where I can find the bracket, or did you tap and die them?

@juneee7067 Год назад

Make sure to unplug the z switch because if you don't it might not work!

@Adam1llion 2 года назад

Great video! What is that shroud around your fan??

@saturdayshanks3753 2 года назад

It’s the stock shroud on the Ender 3 V2 :)

@crooker2 11 месяцев назад

I just bought the CR Touch but haven't installed it yet. Thank you for your guide. So I'm using the Jyers UI firmware. Will the BL Touch version of the software be fully compatible with the CR Touch?

@Fxxje Год назад

I have it as well, but having some issues with it.. My first probe got damaged because it decided to pop-out mid print bumping my buildplate + print on the floor. Also the probe was bent. Looked like a firmware issue to me, since I didnt get it to again before eventually re-flashing the firmware. I read online that I am not the only one with this issue.. Also, My original glass plate is kind of wonky. @ of the 4 corners are quite low and prevent a good layer adhesion. I would expect the probe to fix this by lowering z on those areas, but it did absolutely nothing. Even after installing a new probe, the corner issue still presists. I mean, what is the use of this product if it doesnt do what it is supposed to?

@MrTurtlefan2 2 года назад

Hi, If the nozzle is too far at one corner, but to close at another corner, will the CR-touch adjust to that, or would I need to?

@dea-animator1906 Год назад

I still have the zip Ties i got when I got the Ender 3 v2

@DennisCrawfordJr 2 года назад

When you are felling it, what should it feel like?

@jaydunsmore050897 Год назад

done all these steps now my auto home is in the middle of bed and super high, I try to lower the z and it won't lower, it has no problem going up

@hufftechsolutions7903 Год назад

Remove the z access limiter switch on the left

@jacobjohnson3116 Год назад

Hey so I followed this tutorial but now whenever I print something it heats up to 175 nozzle, 60 bed, then heats up to 200 nozzle, 60 bed, and then both go to 0 and everything starts cooling down, without even beginning to print anything. How do I fix this?

@SvarogGames 2 года назад

hiho i was wondering if you have some tutorial or something i have flashforge finder and after a year it starts loosing steps or layer shifting but i dont know how to tight the belts

@hakandemir3244 Год назад

Can someone explain what the point is of having a auto bed leveling sensor while you can turn the nozzle down and level the bed

@zach_lush Год назад

I had an issue where the 3D printer wouldn't read the SD card after doing the firmware update. I ended up installing a different firmware and it fixed it. I used this one below. GD-Ender-3 V2-Marlin2.0.8.2-HW-V4.2.2-SW-V1.0.7_E_N_BLTouch

@andrzejgowacki1979 Год назад

I have the sam issue. After installing the new firmware, the printer can't read any .gcode files. It has the auto leveling button but it works only partially - the head moves to the center, the nozzle runs towards the bed three times and comes back to left front corner. BUT WITHOUT THE METAL PROBE MOVING! I will check other firmware versions out

@zach_lush Год назад

@@andrzejgowacki1979 yeah try the firmware, I was fighting with it for awhile but installed a different firmware. Fixed the problem

@danielfiander5731 Год назад

Don't you have to disconnect the stop bed level sensor at the side of the printer

@masony8356 Год назад

My printer isn’t reading g codes anymore but the level function shows up any idea what’s wrong? Any help is appreciated

@planmastercopycenter8801 2 года назад

Just install cr touch and new firmware. Can not see highlight bar after update. Board version 4.2.2

@wendigo6782 Год назад

PLEASE HELP!!! After installing my CR touch, I start printing and it performs its leveling at several points (4×4). The problem is that during this upgrade the nozzle turns off for no reason. On the other hand, the heating plate always remains hot. It's annoying because the leveling will be distorted, moreover once the leveling is done the printer does not wait for the nozzle to reach its original temperature again, and starts printing directly. Result: Unable to perform reliable printing. What should I do to solve this big problem?

@andyerwin3535 5 месяцев назад

Does that g29 need to be put on all prints? Or just for the bed test?

@speedlabsllc3945 9 месяцев назад

Thanks for the video. Advice from something I learned early on, your fingers have oils that the bed will retain if you touch the bed. Always clean the bed to prevent warping, or issues with first layer delamination. It helps a bunch to do a quick wipe on the bed (careful not to touch). Makes all the difference and reduces headaches :)

@9495tj 4 месяца назад

When I hit auto-home, the nozzle moves down until tip of the bed levelling sensor touches the bed and then a little more, and then the sensor tip withdraws fully. But I can see that my nozzle is still about 4-5mm above the bd. When it finally completes and goes home, the nozzle is still too high. I can never get the bed level with the auto levelling kit.

@reikyjimenez9097 5 месяцев назад

After starting a print mine auto bed levels the bed again unlike in your video where it just did the two probes?

@Zack-gs2xt 2 года назад

can you do a upgrades video

@justifiedsins6420 Год назад

I did all the steps, but then when it came time to print it no longer show any prints available. Have tried multiple times with multiple different prints

@BzzFest Год назад

Not sure why only the middle top, bottom, left and right are the ones that isn't lined up. Only the corners are leveled.

@A.Roviso Год назад

Mine when it levels doesn't pull the probe up it does it the first and last probe only the rest it pushes down twice goes from blue to red and that's it and I feel like it's not working properly

@nsvaluto48328 11 месяцев назад

How are you on trouble shooting I have mine installed and a filament sensor. When I auto home the gantry does goes down and the touch does probe the bed

@Flirtz420 Год назад

Hi I did everything up to adding the firmware n turning it on. I set my printer to auto home n it won’t move. The car touch is red also.

@eldiablo3124 2 года назад

I installed mine how you have yours but it comes up short what did I do wrong?

@gray896 Год назад

So I have a problem my auto level device isn't going down all the way I'm at negative 10 on the z axis and it still doesn't want to go down for the auto leveling

@easterlingsminiatures 9 месяцев назад

I just can't seem to get the nozzle to where I want it on the bed... I offset the z axis and still it doesn't go close enough when it comes to print... I did all the manual levelling as well... any tips?

@spray_cheese 7 месяцев назад

Same issue, this isn’t much of a “quality of life upgrade” after all…

@rtxbacon4998 2 года назад

Why my Ender 3 v2 stops every time under a hour can you tell me

@MadEvilLemon93 Год назад

i have the cr touch with my ender 3 v2 and each print requires me to mess with the z-offset and it's usually way higher than 0, the last one was 5.68 and the one before that, 6.29. has anyone else had this issue of it always being so inconsistent? i'm considering just going back to manual bed levelling.

@joygibson6623 Год назад

I can't get it to "barely touch" I am not sure how to fix this issue. I'm still looking.

@ady_kotidou Год назад

My CR Touch touches the bed, becomes red, and then doesn't do the whole movement to become purple. Any help? It auto homes just fine.

@jasonking4899 2 года назад

Hi.... I'm quite new to 3D printing.. Just bought the CR Touch and I've fitted to the Ender 3 v2..... But nothing... The firmware for LCD is V1.0.4 .. what is yours? and any other help will be appreciated.

@spray_cheese 7 месяцев назад

Mine won’t do the 9 point mesh after manually leveling it. I’m just gonna get rid of this thing. Not what I imagined

@sh9688 2 года назад

Shouldnt you unplug the Z axis stop cable??

@leektah354 Год назад

Yes, he never mentioned that, you can also remove the switch all together.

@KatazuiOfficial 2 года назад

Howdy! Great tut! I was just having trouble updating my firmware, does anyone else have trouble updating their Ender 3v2 when turning on your printer? My printer just goes to its standard screen with info on the bottom right corner.

@MyBigThing2010 2 года назад

Format your SD card and then load just the bin file to it. Insert SD card in printer then power on. Should fix it.

@xt3hdkx 2 года назад

@@MyBigThing2010 it didn’t help :(

@amosclark9048 2 года назад

Stuck in the same boat

@MyBigThing2010 2 года назад

@@amosclark9048 format your SD card....then put the bin file on THEM RENAME THE FILE ...then insert onto printer n power on. You're welcome.

@MyBigThing2010 2 года назад

@@xt3hdkx you have to rename the file...it will not update firmware of the same name

@patrickscarbrough9843 2 года назад

FYI..... They make the install of the screws of the CR touch to the Bracket look sooooo easy its not got half way done and the hole is so tight it stripped the screws and now it's trash

@danekincade6299 2 года назад

Did exactly everything you did. now nothing shows up on my print to print. cant autohome, and i cant level the bed. any solutions ?

@mynamejevin6227 2 года назад

Did you install firmware for the wrong motherboard type

@nicholasmarshall3191 Год назад

Awesome video, but I am a total newbie so you were going awfully fast for me. A lot of the terminology is completely new to me, and can make this difficult to understand. I will learn!

@zmost8367 Год назад

W man

@meeshelly9157 Год назад

just pause the video at each step - that's what I do

@UhmazinGaming 5 месяцев назад

Man I’m pretty lost with my ended 3 v2 same setup but I cannot get it to print right

@TopofTheHill3D Год назад

why did you install the screws from the bottom -> up?

@slicedpage Год назад

The support bracket has threaded holes, the cr touch does not so you have to attach it from the bottom. Also don't use the 8mm screws for this as I did LOL. Those longer screws(8mm) are to replace the screws that attach the fan housing so as to accommodate the cr touch bracket.

@ScottieLeess Год назад

Hi i had downloaded the firm ware but my printer wont flash ? any idea ?

@JoshyBoy1214 28 дней назад

Does it even change the bed leveling

@theonepristinemonk5528 Год назад

have you made a video about Esteps for us noobs?

@chadiao791 Год назад

How to allow z to be negative?

@Swiipa1Wrld 2 года назад

How come u didn’t need to unistall the z axis chip ..when i had it on my extruder would shoot all the way to the right and make a grinding noise

@helpforourhomeless1819 Год назад

Hey, did you ever fix this? I have the same grinding problem. Thanks!

@sebastianestevezcarvajal3008 2 года назад

Still waiting cr10 smart pro

@brazed420 Год назад

one of my bolts on the underside is stripped...this is brand new and the first time trying it..im using a precision set of drivers and im highly experienced with working on eletronics l. this is just unacceptable....had to fill hole with soder then place a hot bit into it just to unscrew it

@2Cen0 3 месяца назад

Probably a dumb question, but once the firmware is updated, can I go ahead and delete the bin files from the SD card, or does the printer need those files on there?

@evlsc400 3 месяца назад

You've probably figured this out by now, but yes you can delete them.

@terraxcell 2 года назад

When I move z to 0 I still have more room between been and nozzle than I would like 🤔. Bed can’t be adjusted any higher from knobs either.

@Moonsauc3 2 года назад

Make sure you removed the z limit switch completely, also he talks about fine tuning somewhere after 13:00

@terraxcell 2 года назад

@@Moonsauc3 I ended up lowering the z off switch to like -1.2. Seems to be working now.

@dwolfenstein953 2 года назад

@@Moonsauc3 I moved mine down as far as it will go and there still is too much room

@privatemale27 Год назад

Mostly good, but I bet you're going to regret that electrical tape... Sucks how it leaves a sticky adhesive... I just removed the extra zip ties on the wider cable sleeve. If you slide it down the wires, it will expand and provide plenty of room for sliding your touch connector wire through without any struggle. Then pull it longer and zip tie it again. Nice and clean. You can even hide excess cable in there.