Creality Ender-3 S1 - 3D Printer - Unbox & Setup

Подписаться 235 тыс.

Просмотров 159 тыс.

50% 1

Amazon Links
Ender 3 S1: geni.us/CLga
Recommended: geni.us/JustVlads
Official Store: store.creality.com/products/e...
Creality Ender 3 S1 3D Printer, Upgraded Direct Drive FDM 3D Printers, Quick Assembly, with Auto Leveling Bed, Dual Z-axis Screws, Spring Steel Print Bed, Build Size 220x220x270mm
Sprite Direct Dual-gear Extruder
Creality Ender-3 S1 3D Printers Use Brand-new self-developed "Sprite" direct dual-gear extruder features two chrome steel gears . The extruder realizes smooth feeding and discharging of filaments without slipping and works extremely well in printing flexible filaments such as TPU. Compared with other direct extruders, the "Sprite" is lighter and features less inertia and more precise positioning.
CR Touch AUTO-Leveling bed
Ender 3 S1 3D printer is equipped with CR Touch Sensor, which is independently developed. The intelligent leveling system can automatically compensate the error height (accuracy ±0.04mm) at different points of the printing bed, which effectively improves the model printing quality and printing success rate, and makes leveling bed more easily more precise.
Power Loss Recovery and Filament Sensor
Ender-3 S1 features the function of detecting filament runout or breakage/power loss and resume printing after recovery. By accurately recording the printing data at the time of power outage/filament runout or breakage, it helps to avoid the waste of filaments and time caused by accidents.
High-precision Dual Z-Axis Higher Printing Precision
With a Z-axis dual-screw+Z-axis dual-motor design, Ender 3S1 works smoother and more synchronously to lower the possibility of lines and ridges on the sides of your print, thus improving the printing quality.
As an Amazon Associate I earn from qualifying purchases
My website: www.justvlads.com/

Наука

Опубликовано:

27 окт 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 154

@JustVlads Год назад

New Channel: www.youtube.com/@Just_Print Ender 3 S1: geni.us/CLga Recommended: geni.us/JustVlads

@Craftsbymonojit Год назад

Hey can I print with abs filament on this printer? Please answer

@tomlaning4145 Год назад

@@Craftsbymonojit yes

@PodDecks Год назад

You’re a legend. This video was so freaking helpful. You deserve a medal (3d printed of course)

@thefirm7708 Год назад

I agree, very well explained video and very helpful.

@MrCarroll Год назад

This video is exactly what I was desperately searching for. I am 100% new to printing and Creality included basically zero instructions on how to get started or to print. Thank you for making this with such high quality instructions and detail. You the man!

@allenpaley Год назад

Hey Vlad. I'm about 6 weeks into my exciting 3D printing journey, and I just realized something: Your old Ender 3 Pro unbox/setup video was one of the first videos I watched on the subject, and gets credit for convincing me to take the leap. You're putting out good stuff, and pulling more people into the hobby. Keep up the great work!

@monoboy5236 Год назад

This was really great. This is my first printer so I appreciate the in depth things to check beyond the assembly manual. You're a legend and this was super helpful.

@panosfxable 10 месяцев назад

Newbie here just got my S1, i had a very small childish printer send to me to try it out and in about 2 days i was so hooked up with this hobby! Really love it! BIG/HUGE Thanks to you Vlad for helping me out set up this nice Printer! Your video is really what we all starters and non starters need when purchasing something new!

@goddamnit Год назад

Thank you so much for this extended setup tutorial! I made sure to set up everything, including the belts, tightness, springs, etc. that you showed, and I printed the Rabbit with Polymaker PolyTerra Matte White PLA Filament, and it turned out great! I can't believe how smooth it turned out as my very first print! I hope I'm not jinxing my future prints here haha... anyway, thank you SO MUCH again for this video!

@DrenLithear Год назад

New to the hobby and picked up this model on the black friday sale. This was a great vid and will be watching through it a few more times once it shows up.

@BeverlyMiller-hx1yd 6 месяцев назад

AMAZING!!!! I was seriously banging my head on a wall last night trying to figure out my issue with printing - went step by step with you and printing my first project (the rabbit) successfully!!!

@KenMrKLC Год назад

By far the best most complete overview and basic tutorial I have seen. Thanks so much for making this. I will be sure to follow and support you in the future. I am on my way home with my first 3d printer and 3 rolls of filament to play with.

@NebTek Год назад

I'm getting this exact 3D printer and this video was so helpful. It was super satisfying to watch as well from setting it up to actually printing. Thank you!

@WhimsyCottage Год назад

Rookie mistake: the Y axis didn't make that click noise, (started making a grinding noise) scoured the internet for answers, then moved my printer forwards and it turned out I didn't give the wire at the back enough space to move all the way back. Just posting this here in case anyone is trying to figure out the same thing, lol

@MIDNIGHT8212 Год назад

You are awesome. By following your setup instructions, my first two prints were successful! Thanks for making a beginner feel confident!!!

@DC_tronicFPV Год назад

This was incredibly helpful after picking up my first printer in the S1 model.

@vintagecornet 11 месяцев назад

Unlike 90% of these YT videos, this one is extremely well done and informative. One can actually see what you are showing, and even better, I can understand what you are saying. I will be setting one of these up tomorrow and this was a great help. I have to watch the last few minutes to be sure that you didn't, but about the only thing you didn't address was printing from a PC with a USB A-C cable. If that's the case, that might be a nice additional video. I've been printing from a PC on an Anet A8 for several years and prefer that to cards or USB thumb drives.

@dancwilliams 10 месяцев назад

I am brand new to printing and was gifted an Ender3 S1 for my birthday. This video has helped me so much. Thanks for taking the time.

@PennySizedDreadfuls 11 месяцев назад

I simply need to thank you for your help. This video saved me. I opened the box and almost cried 😅the instructions were terrible and I don’t think I could have done it without this video. Thank you so much!

@xerenityapexlegends3940 Год назад

Looooved how you went over the parts while saying their purpose and whether they were optional. Really helped put a goal and direction in my brain before the actual instructions.

@Hokey412 Год назад

Dude you're the GOAT for this video. Helped me out so much setting mine up. Thanks!

@alternativeplan9111 Год назад

Thanks a lot! Setting the printer up was quite easy following your tutorial. First print turned out amazing!

@M7MD0o Год назад

This video might be the best way to display a 3D printer. I’m looking for my very first printer and this made feel very confident of my decision. Thanks a million.

@boogalooG520 Год назад

When I opened my Ender 3 S1 I found a nice booklet instead of the foldout version you received. Pretty cool, thank you very much for this video!!

@staxpetrick 6 месяцев назад

Thanks for the set up video. Set up my S1 perfectly because of this video.

@squatchusmc9133 Год назад

just got this printer, possibly the last one anywhere as i can see at the moment. Microcenter even said they were out. On the way back to get a different printer altogether.... he found it misplaced and no one knew where it had come from. LUCKY ME! Yours is the first video I have watched on unboxing and review as im about to start my journey today! Awesome job and keep up the good work!

@zgSH4DOW 8 месяцев назад

The change from Ender 3 Pro to S1--wow, I'm glad I got back into 3d printing

@gregscarcella519 Год назад

Excellent video. Very informative and good closeups!

@TomInSomerset Год назад

Awesome! Just got my Creality Ender-3 S1, and had some issues w setup and initial use (using the Creality docs and videos). Searching for help on RU-vid, I found this video. It soon became clear what the problem was (user error of course), and all is now well. Creality should pay you to make their unboxing and first use videos. Thanks!

@xvalen4827 Год назад

First of all i thank you for the video Vlad, it was extremely useful, well explained and complete. I also want to point out something critical in it so nobody else (or maybe another noob at 3d printing like me heh) gets hurt in the process. At 16:20 you tell us to loosen the adjustement nut, i do understand the need for a smooth movement but now the problem i got from doing so was a loose platform/bed, it was wobbling and messed my second print up. I did stress out all day believing that my printer had a factory defect but no, the solution was quite easy. Instead of loosening the thingy at 16:20 you need to be really careful or even TIGHTEN IT UP until your platform is stable and doesn't wobble. Cheers folks and i thank you once again for your video Vlad!

@johnkmoore99 Год назад

I was too lazy to read the instructions and found this video. So glad I did, I learned a LOT more than I would have reading that pamphlet. And it was much more enjoyable. Thank you!

@diamondly6250 6 месяцев назад

the instructions it came with is hard to follow to i watched this

@38373145 Год назад

Idk is it just me, i swear the instruction paper was missing some steps. Thankfully I came across your video before i turn it on cause I definitely missed on connecting 2 wires, didn't know where to change the voltage, and have no clue about the leveling. THANK YOU SO MUCH!

@shallahk8403 6 месяцев назад

Wow, I learned so much watching this video. My first 3D printer setup and print came out perfectly, your detailing was so helpful. 200x better than creality’s. Truly 3D printing intimidated the heck out of me, just reading anything about it, half the terms were unknown to me, I bought the printer and let it sit for a month because I truly dreaded putting it together. If I’d seen your video first, I’d have jumped on getting it done right away. Thank you so very much for all the detail and walkthrough, even the quick overview and explanations of controls, & adjustment recommendations for the programing on the computer really made working with this printer seem doable, lol!! 🎉🎉❤❤ Thank you very very much! I’m putting your video name in my Amazon review to help others like me!

@scottsomebody4578 4 месяца назад

Nicely made video and review. Now I think I want one.

@edwinocasio1622 Год назад

Thanks for the help with the leveling you’re amazing

@jocquismith643 Год назад

Thank you! Saved me a lot of time!❤

@paulosimoes1891 7 месяцев назад

This video is awesome, thank you very much for the explanations

@akashsonawane5297 Год назад

Great tutorial sir. It seems very helpful to me assemble my 1st 3D printer. Thank you very much.

@lewismealing1531 Год назад

Thanks so much, this was incredibly helpful!

@matthewchotai662 Год назад

Great vid you cover alot for beginners or people who are shopping for a new printer. 👍

@angietrichell9849 Год назад

I put the instructions down and watched your video. Got it going. I have a few other Enders even though I am still very new at this. You helped get me started with this printer easily. Thanks. Rabbit printed fine but there is a bitcoin looking gcode with Ender on it that I had to tweak with some to get it to stick. Plain white PLA. I managed. Like the duo z rods and direct path from the spool to the extruder. I have so much to learn and promised to not buy anymore 3d printers after this one. Lol.. I use all my printers.. I love how easy you are to understand. Please keep making these videos for noobs like me.

@nekohuntress99 Год назад

jugging by the small size of the models you printed the printer did a good job specially in the price range

@dannypboy 9 месяцев назад

, I am Daniel from London I just have to say I I am so impressed with your video. I've just bought one of these and you have helped me so much you explain so easily and simple. Anyone can understand I thank you because I have your video on save And refer back to it even your installation set up impresses me. I will use that step-by-step to build it so once again thank you, the best help video around

@akaiphone 10 месяцев назад

Awesome video. I used it to set mine up. The problem I’m having is leveling the bed I manually level three or four times and then set a Z offset and Ron auto leveling readjust, the Z offset at the end, and when I come to print the nozzle is either dragging on the plate or about 3 mm off so I am constantly adjusting it in the beginning of each print. I tried the leveling process know multiple times but it’s the same outcome, it’s driving me crazy. When I go through the leveling process everything is perfect. I click on auto home and bring Z down to zero, and every single time zero stops at a different place than where auto leveled but most of the time it sits right on the bed, so I have to check before each print if not, I will drag the nozzle. I use the PA sheet and when he drags it damages the nozzles subcontractor nozzles already because I forgot to check the leveling before printing.

@knoptop Год назад

Great video! Very helpful, thanks!

@3dman875 Год назад

very great video I really enjoy your video on the printer

@Stephmadeitforyou 11 месяцев назад

thank you for this very informative video!

@mirandaploss9547 6 месяцев назад

Hi! Thank you making this video. It’s helped me so much in setting up my printer. Can you share the settings you used for printing with TPU?

@caseyboone7018 Год назад

Awesome video! I just got the ender s1 which is my first ever printer and your video covered basically everything I needed to know to get started. I have one question though, on most eccentric nuts the screw holding it would spin with the nut, this wasn't a problem for most of them except the ones on the bottom of the build plate. Do you have any suggestions?

@albertocarmona3815 Год назад

Thank you sir you saved me a lot of time

@rickgranados7844 5 месяцев назад

very helpful. thank you.

@johnh.miller1112 Год назад

Hey Vlad, Your videos are my go to when it comes to 3D printers. I spent the morning looking high and low for the E3 S1 bed handle file. Go figure why Creality named it “shaking hands”? I finally found it and printing it now. I own three Creality printers, CR-10 Smart Pro, E3 S1 Pro, and E3 S1 and they were all very easy to setup and run especially after I watched your step by step video. The all run 24/7 with very few problems. Still working out a few adhesion issues but it’s part of the learning curve. Only printing PLA for now until I figure out recipes for TPU and PETG. I’ve recommended your videos to others on Facebook. Thanks again!

@jclosed2516 Год назад

He demonstrated that bed leveling, but I wonder if you have to store the Z axis value after tuning in. He did not showed it. Is it automatically stored? Because if not all these settings are lost when powering off, giving you some nasty surprises when powering on and start printing without checking the Z-axis. I very much like to buy this printer. I guess it's a tad less modifiable then the standard Ender 3, because it looks like you cannot replace the motherboard for another brand like BigTreeTech. However - There seems to be a very much improved (open sourced) version of Marlin firmware available, so you can at lest do some tweaking (unlike the Ender 6, 7 and Sermoon printers that only have closed source firmware, what is definitely holding me back to purchase them).

@mbjac Год назад

When you start an ender print, it does a line of filament from front to back to purge the nozzle, now when you pause a print, and want to resume, and the print you've paused is higher in hight than the gantry does it still do that filament test from front to back on the bed again because if it does the arm will hit the print?

@GhostForge Год назад

Thank you so much for this video!

@readme373 10 месяцев назад

really helpful thanks

@dang4254 Год назад

Great video! Thank you so much

@user-ci8lb2hx1d Год назад

Best video for sure! What should i use- cura software or the one in the video?

@br0k3nilluzion Год назад

Are you going to be using the Sonic Pad with this? Could you show an install with it on this and how you'd mod a PrusaSlicer profile for it for tuning and all ?

@rogerthatstudios Год назад

Thank you!

@chaitanyaaashritha3264 Год назад

Thank you so much sir. Such a greate expalination.

@jamesc.7988 Год назад

I want to swap out the touch screen on my S1 Pro for the V2 display with rotary knob. Is it a simple plug & play? Or will there be additional steps required?

@JDHitchman Год назад

I did not get an SD card with my Ender 3 S1 so I did not get that handle file. Do you know where it could be downloaded from?

@ijt540 11 месяцев назад

great video thank you

@user-ci8lb2hx1d Год назад

Can you make a video about all the parameters from the software?

@drksun Год назад

I have an extra bag of screws, 2x m5 + nuts. What are these for?

@midwesttumblersllc3822 Год назад

This is a great tutorial, however the slicing software seems a lot different now, unless it because I’m on a Mac. Anyway you could do an updated video with the updates software? I don’t see any of the settings your talking about.

@calebkincaid3031 Год назад

I love this guy

@urkskn8842 Год назад

Thanks dude

@MUDHD Год назад

Hi, would you recommend this printer more, or an Anycubic Kobra?

@m47tito 4 месяца назад

I have a question about this ender 3 S1? I have this ender 3 S1 and I don't know if I can see anywhere on the screen during printing which layer is being printed at that moment. Is that visible somewhere?

@JaySingh-gu7pg 5 месяцев назад

Hello Vlad i bought the Creality Ender-3 S1 and i have been trying to do test prints but the cooling fan touches the print and then knocks off the print from center. do you have any suggestions to fix this from the fan moving the print?

@jswc3 Год назад

This was a great video. It helped me a lot. Do you worry about fumes with PLA? Should I take precautions when printing in my living space? I am new to 3-D printing.

@MrAmity009 5 месяцев назад

Bud what is added value in comparison with the original ender 3 ??

@devarora4969 Год назад

Can you recommend which 3d printer should I get between the ender 3 S1 or the elegoo Neptune 3 pro ?

@bugrademirel Год назад

Hey great video, do you think i should go for the cr 6 se or ender 3 s1?

@woltea Год назад

hey dude, when we compare the creality ender 3 v2 neo with the Creality Ender 3 s1 print quality, which one do you think is better v2 neo can print at 0.05mm layer height, s1 is 0.1mm layer height. I'm thinking of buying the v2 neo because it's both cheaper and more up-to-date.

@dareka9425 Год назад

I SHOULD'VE WATCHED THIS VIDEO FIRST! This is my first ever 3D printer and I built it straight out of the box with the included instruction manual...a manual that was apparently made for ants since I had a hard time reading the microscopic prints! Either I missed some essential parts or it was omitted from the book but I connected the wrong cables to the Z- Axis motor. So when I chose the leveling option as per instruction the motors creaked out loud like an old car and dragged the print head across the bed. Now, here's a scratch mark running right in the middle of my magnetic plate! I took a break and finally watched this video. I discovered the mystery cable still taped to the base is the actual connector to Z-motor. It ran smoother and quietly as it should but it still took me a couple of more hours to solve the failed prints(the print head was way too high from the plate).

@jacobholmes8982 Год назад

How did you fix that. I’m having that issue now

@dareka9425 Год назад

@@jacobholmes8982 RU-vid was my fix. I started adjusting the bed level using the paper technique at optimum bed heat so the early failed prints begin to get less. The early failed prints still pop up occasionally because the bed's height fluctuates with the heat and messed up the calibration. Failures or errors past the early layers, however, are a bit harder to explain. Currently, I'm facing a particular filament that is giving me a lot of headache. It blocked two hot ends and fused one of them.

@erwinn58 5 месяцев назад

You are an amazing help

@Goody1926 11 месяцев назад

Thanks!

@luemas2766 Год назад

How did you get the display screen to auto black out? Btw well described video. 👍

@toadsage Год назад

Is there a reason why you recommend preheating before you level the bed?

@66customsnj Год назад

Do you know if the machine stops if the filament runs out?

@SpaceXToMars Год назад

Wow, better video than the one from Creality! Thanks

@taofiqlawal4917 Год назад

28:47 What?? Does anyone know how he raised the printer after "disable stepper." I tried pulling on it after hitting this option and mine wouldn't budge!

@WoodenRailwayFan1234Production 4 месяца назад

Will any 3d printing software work? Like Sketchup?

@L1FEPORTAL Год назад

can u do a video with the new biqu hurakan

@paulhindley8803 Год назад

Just got this for £219 a Black Friday deal! had to cancel the V2 Neo i had ordered but they are the same price and this one looks load better. Hhope ive made the right descision!

@beau6699 Год назад

How is it? I’m thinking about getting this one.

@justyouraveragepeiceoftoas1988 Год назад

What are the wrenches and the m5x12 screws for ?

@milosdjordjevic8272 Год назад

Ender 2 pro when will it be? Tnx

@SnappyDrift 10 месяцев назад

Would you mind sharing your tpu settings with us?

@Marcel_C5 Год назад

Hello! What are the real dimensions of this printer? All official measurements include the Spool holder on top, but I need to know the measurements without it.

@mssweetychessgir 11 месяцев назад

do anyone know what filament he used for each 3d print he did?

@arsenalprime6933 Год назад

I don’t know why but every time I try to print something the filament doesn’t stick to the base. It just comes out hardened

@jakabgipsz4788 Год назад

14:48 There's a label with an arrow on it to put it in the plastic holder. So exactly where it is marked. Why didn't you?

@kimjin1194 День назад

I had an Ender 3, and the s1 will be my second 3D printer. Any suggestions?

@luckyplayzminecraft0006 Год назад

yeah the one near the connecter on the fillment detector is out.

@Tidumm Год назад

Hi just vlad! Following u for a long time since like 2020 n I like watched almost every video of yours since then. Please guide me I want to buy a 3D printer for myself this time so pls gimme some advice, I always get confused which printer should I buy resin printer or a filament printer. Pls help me you would do me a huge favour 0:22

@aarongoodman3705 Год назад

When I drag and drop or choose Open File with Creality Print I'm stuck at preview mode and can't access any of the toolbox, anybody else having this issue? When I cancel it just clears the model

@toadsage Год назад

Thank you so much for making this video, Vlad. I had some difficulty with leveling my bed (and I accidentally melted a hole in it with the hot nozzle 😅) but for the most part, setting up my printer went smoothly thanks to this video. My first print, a Cali-dragon, went flawlessly because you recommended settings for the slicer. I appreciate it!

@Bluedragonfrog 7 месяцев назад

thanks

@vex123 Год назад

Excellent video. I'm completely new to 4d printing and looking into buying a S1 and this has really helped me get a head start. All said, I think you should get a better camera. You have great content, but some of the video shots are blurry especially the UI screen even at 4k.