No video :(

CURT TruTrack™ 4P Weight Distribution Hitch Installation

Подписаться 12 тыс.

Просмотров 146 тыс.

50% 1

This video depicts the installation of the CURT #17500 TruTrack™ 4P Weight Distribution Hitch. This install will the same for #17499, #17500 & #17501.
Install Sheet:
www.curtmfg.co...
For more information:
www.curtmfg.co...
MAINTENANCE: Keep the socket-mounted ends of the spring bars and the lock pins in the head assembly free from dirt and well-lubricated. Excessive wear in this area may indicate an overload or inadequate lubrication. Keep the head assembly exterior clean. Do not allow dirt or stones to lodge between the spring bars and the head. Keep hitch parts painted to prevent rust and
maintain a good appearance. Do not paint over labels. Keep lift brackets clean and lubricated to ensure ease of operation.
Special Notes:
All Steps must be followed to ensure correct function. To verify proper installation once installed, test by connecting a test light or properly wired trailer.
CAUTION: The tongue weight rating of the spring bars represents the capacity of a pair of bars, not an individual bar. Always use a pair of spring bars and be sure they are of the same weight ratin
Looking for help with your weight distribution hitch setup? Here's 8 easy-to-follow steps: www.curtmfg.co...
Follow CURT for more!
Facebook: / curtmfg
Twitter: / curtmfg
RU-vid: / @curtmfg
Instagram: / curtmfg

Опубликовано:

25 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 16

@curtmfg 4 года назад

Towing requires the right products and the right setup in order to keep you and everyone else safe on the road. If you have any product questions, or need installation help, we're here to help. Give us a call at (877) 287-8634 ext. 2 to speak directly with our product support team. Tow safely!

@jondrew55 3 года назад

I just installed the 17499 which is quite similar. It took about 4 hours to install and adjust. If you’re thinking of DIYing this here are a couple of suggestions. Dry fit the bar support arms on your trailer frame and if you have more than 3/4” of extra threads on the bolt cut the bolt down. This applies to the lower bolt in particular as you will be taking this one on and off several times to tweak your spring bar tension (unless you get very lucky). Also. Put the head on and see where the bar arms will have to be located. (4” in from the end of the spring bar). Depending on how your trailer frame is constructed and wheee your LP tanks are located, you may not be able to install this hitch. I literally had 1” to spare. You’ll need a torque wrench capable of tightening the hitch head 3/4” bolts to 200 ft-lbs. this is not something most DIYers have laying around. I’ve had a couple of weight distributing hitches before. They were all the chain adjustment type. I’m not sure I really like this style of hitch. It is not easy to adjust spring tension. Based on a difficulty scale of 1-5, with 5 being the most challenging I’d rate this one a solid 3 and probably a 4.

@ReadySetAutismFamily 3 года назад

Great information you have provided! Thank you

@uglybobhere 5 лет назад

OK here goes. Had the Curt 17500 installed at dealer and now ready for first trip out with it.

@curtmfg 5 лет назад

How did you like it?

@uglybobhere 5 лет назад

@@curtmfg so far so good.

@mhardy006 8 лет назад

At 6:00 you suggest using the lift bar as a lever to pry the spring bar off of the L bracket. That instruction and your demonstration makes no sense. Putting the spring bar on top of the lift bar requires SIGNIFICANTLY more effort than to just pull it off of the L bracket. Aside from that, Great instruction and very helpful! My dealer did a terrible job setting this up and using your instructions I was able to do it correctly.

@libbey01 2 года назад

Awesome video!

@alvashoemaker8536 4 года назад

Thanks for that info...! 👍👣

@ztrguy 3 года назад

Anti sway too ?

@curtmfg 3 года назад

Built-in!

@debraparoli1733 8 лет назад

Hello;I purchased the Curt Weight distribution complete kit with sway control part # 17063. Do you have a video on how to install this kit? Thank you.

@curtmfg 8 лет назад

+Debra Paroli We apologize for the inconvenience, we have filmed the installation video because of your comment! It will be available shortly. Thank you!