Cutting Board Handles Using a Router Table - A Do Over!

Подписаться 9 тыс.

Просмотров 13 тыс.

50% 1

Cutting Board Handles Using a Router Table - A Do Over! My new process for putting handles on cutting boards without using math!. This time I actually show the outcome!
Original Video Here 👉 • Routing Handles into a...
NOTE: Some links are affiliate links.
Parts used in this video:
Pocket Squares - amzn.to/3WH2moj
Core Box Bit 3/4" - amzn.to/3WInZEx
Bowl Bit 3/4" - amzn.to/3GmfEBq
Table Saw - amzn.to/3jvHdPE
Router Lift - amzn.to/3VrnAWj
All my Tools and Gear 🛠 🪚🧰
👉 kit.co/cyberre... 👈
STAY UP TO DATE (@cyberreefguru)
👉 linktr.ee/cybe... 👈
■ Etsy www.etsy.com/s...
■ Instagram / cyberreefguru
■ Twitter / cyberreefguru
■ Blog www.cyberreefg...
■ Shop www.cyberreefg...
Don't forget to subscribe and ring that bell!
Music by:
ampletunes.com and Epidemic Sound

Опубликовано:

16 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@davidf9630 7 дней назад

Thanks for a great video. I came across some sticks that were going to be thrown away from a cabinet shop and I’ve made 30 cutting boards. I have a 10 inch planer and a lot of glue. So far they’ve came out looking very nice, there are a mix of black, walnut, cherry maple oak, and even some purple heart.this video has given me the information I need to complete the transformation from sticks to beautiful cutting boards. Thanks again. You do nice work.

@cyberreefguru 5 дней назад

Thanks David -- sounds like you have a great project. Thanks for watching!

@rfrhoad 10 месяцев назад

One suggestion would be to run both flat sides against the fence - this would guarantee a perfectly centered handle.

@cyberreefguru 10 месяцев назад

I used to do that but stopped simply to save some time. Perhaps I will start again - thanks for watching!

@kenerickson4923 11 месяцев назад

❤I put tape on the face of both ends of board and mark width of groove on the tape. I mark left and right edges of the bit on the router insert. Then I make the cut starting and stopping when the marks align with bit edges. No measuring and no stop blocks needed. I also have the half finder jig to align bit center to fence distance. This method is simple especially when doing multiple boards that vary in width.

@cyberreefguru 11 месяцев назад

Thanks Ken - do you cut the full depth in on pass? I usually take 3-4 passes so I wouldn't rely on myself hitting the same stopping point each time. Thanks for watching!

@kenerickson4923 11 месяцев назад

@@cyberreefguru I do 3/16 deep groove in 1 pass.

@blandry021 9 месяцев назад

Great instructions, I will be saving your video for future cutting boards.

@cyberreefguru 9 месяцев назад

Thanks Brian - thanks for watching!

@MrDfurlong Год назад

Nice technique

@cyberreefguru Год назад

Thanks and thanks for watching!

@wileybucey1740 11 месяцев назад

I find keeping the board vertical and not tilting it towards you is the challenge. I’ve wondered if two sided taping a right angled triangle(s) to the board would help keeping it vertical.

@cyberreefguru 11 месяцев назад

I brace mind against the fence and slowly lower it down. Sometimes I accidentally tip it one way or another, but it usually works. Having something that extends the fence up would be best, like you can do for a tenon jig or cross cutting on a table saw. Alternatively, there are jigs that seems to work well. I'm going to check some of them out and see if they are easer to use. Thanks for watching!

@wileybucey1740 6 месяцев назад

Thanks. Do you round over the board edges with a router before or after you router the handholds?

@jaa522 11 месяцев назад

what type of router bit did you use?

@cyberreefguru 11 месяцев назад

Hi John - I used a 3/4" Bowl Bit - amzn.to/3GmfEBq. Thanks for watching!

@jacktrotter5357 4 месяца назад

Do you cut board in vertical or horizontal position , thank you ? Jack in Idaho

@cyberreefguru 4 месяца назад

Hi Jack - I cut them in the vertical position (6:38) since the bit is facing up. You can get a ball bit (amzn.to/3ULJvcq) to cut horizontal, but then your depth is limited to the width of your bit.

@Itmovesme1 11 месяцев назад

way to complicated...

@cyberreefguru 11 месяцев назад

Hi Carl - please help me -- describe a process that is less complicated? Thanks for watching!

@WalterMelons 7 месяцев назад

@@cyberreefguru⁠I am not the person you responded to but I found Amana makes a fluting bit with a bearing so you can set the height and then run the board on its side rather than on its end. Thats the only thing I’d change in your process. Also woodline USA makes one too.

@cyberreefguru 7 месяцев назад

@@WalterMelons excellent - I will have to check that out!

@WalterMelons 7 месяцев назад

@@cyberreefguru Yeah for sure. The bit is less exposed, I still take a few passes to get to full depth but at its deepest cut the outermost part of the bearing is exactly even with the fence. Also I feel like I have more control over the board because it’s on its side on the table instead of on its edge against my small fence, and when finishing the cut I just pull away from the fence so you don’t get the artifacts like you were explaining, or at least not anything noticeable.