Cylinder Install Lycoming O360 Engine

Подписаться 2,6 тыс.

Просмотров 22 тыс.

50% 1

See how we install brand new cylinders on a Lycoming O360 aircraft engine. This engine is being major overhauled and we are installing new Continental Lycoming O360 Cylinders. Once it's complete this engine will go to Ketchikan, Alaska to be installed on a Piper PA 12
Follow along, watch and enjoy!
We will post PART 2 of the Cessna 150 restoration next week. Please subscribe and click the notification bell to see our latest videos when they are released.
Check us out online and on instagram :
www.alaskaairc...
/ akcylinders
We hope you enjoy our videos, thanks for watching!
We are a small aircraft engine overhaul and machine shop located in Wasilla, Alaska.
***This video is meant for entertainment purposes only and should not be used as a guide. You must be a certified mechanic to perform this operation following only the applicable manufacturers instructions.

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 36

@mbe9682 2 года назад

No clips for the gudgeon pins? He failed to clip the piston pins in to position.

@skipper3733c 4 года назад

I see that you torque the 1/2 inch nuts in a diagonal crisscross pattern. My 1974 Direct Drive Manual shows a circular pattern. Has Lycoming revised this. I like your improvised torque plates!

@tl3139 2 года назад

I used to work at a shop called Mattituck Aviation. I was responsible for cylinder overhauls on Continental and Lycoming cylinders.

@carlospiezzi4030 3 года назад

Good morning and congratulations on the video, when you saw the installation of the cylinder heads and saw that they did not place the piston bolt locks, check other comments and many of them had the same thing that happened to me and do not ask about this, in more than Fifty years repairing automobile engines I have never seen anything automatic in the installation of piston pins, I will try to get information on this system, thank you very much and greetings from Buenos Aires.

@wp4246 Год назад

These are great, why did you stop?

@derheeheehee6941 4 года назад

The OH manual and SI 1029 says lube the through stud threads, but doesn't specifically mention the deck stud threads. I can't tell what you guys did. Every shop i've called says lube all threads liberally. Lycoming will give you two different answers, depending on who you talk to.

@akcylinders 4 года назад

Yes you’re right, it’s a bit vague. At our shop we have always put oil on all of the cylinder base threads. 👍🏻

@derheeheehee6941 4 года назад

@@akcylinders Interesting ly enough, the 0-360 MM Says to lube all threads with food grade anti-seize. What the hell!

@crazypilot4017 Год назад

Nice 👍

@danielbastino8376 4 месяца назад

Excelente job.

@charleskuss8538 2 года назад

I note that you only installed torque plates on one side of the engine. Is that because this crankcase uses studs threaded into the other half of the crankcases? A bit misleading as you don't show the wrist pin buttons being installed onto the wrist pins prior to shoving the cylinder down.

@av8tore71 2 года назад

This will bolt right in to my Mooney

@stevewillis1708 4 года назад

Nice work!

@akcylinders 4 года назад

Thanks!

@airplanemechanic5561 Год назад

Thanks! I'm replacing all 6 on my Continental 470. What do you use for assembly lube?

@andyamendala6611 3 года назад

I would also add that the torque pattern used is not consistent with Lycoming's documentation. More concerning is that no lubricant appears to be applied to the stud and through bolt threads, nor to the cylinder base plate area. The lack of lubricity will result in inadequate preload being reached during the torquing operation. Lubrication of the fasteners is clearly called out in Lycoming's documentation and has been standard practice for eternity. Please do NOT dry torque these fasteners if you're doing your own cylinder work, you will not achieve the appropriate clamping pressure on the crank bearing, or reach proper fastener preload, which may result in a cylinder departure from the case or a spun crank bearing and subsequent oil starvation.

@MrElkhunter01 4 года назад

Great videos! In the process of rebuilding my O-540 cylinder (just 1 cylinder). Had leakage thru the exhaust valve. It appears some carbon was holding the valve up and also the ex. guide is worn. My question is, can you do a video on replacing the guides and reaming to the proper size, etc. Thanks!

@akcylinders 4 года назад

Right on good for you! Not surprised to hear the exhaust guide is worn. Thanks for the recommendation that is a great video idea. We will try to do that in the near future! If you need any advice/help repairing that jug message us on Instagram @akcylinders

@rx7fanrx8owner64 4 года назад

What keeps the piston pins/gudgeon pins from pulling out and damaging the cylinder wall.

@akcylinders 4 года назад

Nothing! The pins have aluminum or bronze plugs on the ends to protect the cylinder wall. But they just float in there 😄

@rx7fanrx8owner64 4 года назад

@@akcylinders thank you for your reply. Good job you guys are doing there. I always learn something new from you .

@k-lubgamingchannel3771 2 года назад

How do you get the connecting rod to top ddead center?

@chippyjohn1 3 месяца назад

People in the US restore a lot of WW1 engines

@badattitudeaviation 4 года назад

Great vid..I didn't notice piston pin plugs going on?...is it different than my io 320?

@akcylinders 4 года назад

Good eye! We installed Superior Air Parts piston pins, which have pin plugs pressed into the ends rather than the OEM Lycoming pins which use a removable plug on the ends. 👍🏻

@T18skyguy 3 года назад

What kind of assembly grease are you using there ? Good video by the way !

@akcylinders 3 года назад

Thank you! We use a mixture of engine oil and lubriplate #105

@bice19701 2 года назад

Irritating note in the lycoming manuals state to torque 1/2 and 3/8" nuts........the nuts are actually 9/16 and 3/4" I believe. I assume they mean the studs are 1/2 and 3/8"

@akcylinders 2 года назад

It is misleading and annoying but that actually is the correct way to say it. 1/2” nut or 3/8” nut refers to the thread size, not the size socket it uses. Might also see 1/2-20 or 3/8-24 giving the the thread diameter AND thread pitch. You are correct on socket sizes though! They use 3/4” and 9/16” socket 👍🏻