DERALE REMOTE TRANSMISSION COOLER INSTALL ON CHAOS THEORY CAMARO 

Glad it was helpful!

Thanks brother. I appreciate it. Hopefully it does it’s job. For me AND fpr you. 👍

Glad I could help

Thank you sir!

Glad you liked it

That’s the video I was referring to that made me pull the trigger on this cooler. Mines not mounted to a flat surface. It’s mounted in a bubble so there’s about 1/2” of space behind it already. 😉

If its got a fan then I dont see why not!

@@BadLuckGarage currently it done I got it from Novak which specializes in jeep V8 swaps relocating box on the winch will help some too I’ll show you a picture on Fb messenger

So far it seems to be working great!

@@BadLuckGarage Got mine in..

Glad you enjoyed it brother. 🤣👍

Because the shape of the floorboard blocked them.

What power steering? 😄

@@BadLuckGarage right lol, forgot your not running it ha

😉

Yep. This videos almost 2 years old so there’s entire playlist of them. Check out the Chaos Theory Camaro playlist. We actually just moved the cooler to the rear of the car a couple weeks ago to make room for subframe connectors. But we had zero issues with it under the floorboard. Of course we weren’t using a transbrake up until now either and obviously that builds heat fast.

Yes is preset

😄

All that was covered in the first 2 minutes of the video.

You need a thermostat switch wired inline. Having the fan running all the time will just wear the fan out that much faster. It may also cause the transmission to never warm up in cooler weather.

Works great

I hope so! Got rid of two extra lines in the engine bay too!

@@BadLuckGarage cleaning up the engine bay for more turbo space 😎😈

Doesn’t matter. Only matters that the sensor is on the trans output line. Cooler comes with instructions that explains everything.

Yes and no. It was jetted for a 200 shot but it wasn’t flowing a 200 shot because my solenoid line was too small restricting flow. I explained that and upgraded the line several videos back.

No issues. Check out the newer videos for updates. 👍

Yes the Holley HP EMS was donated by one of my subscribers.

Your transmission has a pump

eBay cable cutters

Thanks for watching! Glad this video helped you out!

Watching the video would have answered this question.

​​@@BadLuckGarage watched about 4 minuites of it and can't finish it because I'm at work but thanks for your enlighting comment I'll figure it out.

@@JeffAMay your welcome. And ironically enough your question should have been answered within the first 2 minutes.

@@JeffAMay 4:30

@214 Parka Also 1:45 and at least four other times throughout the video. Lead a horse to water and all that. 🤣👍

Lol, when I’m watching other people’s videos I do the same thing brother. 🤣🤣👍👍 I actually contacted Motion Raceworks after I saw that video to confirm exactly which cooler they were using on the Nova to make sure I got the same one.

Yes I stated that in the video. The way I wired it is exactly the way it’s supposed to be wired. Except the relay would be activated by an ignition hot instead of the temporary switch I installed. There’s no need to buy any special relay. If you want to override the thermostat switch all you have to do is run ground from the fan to a separate switch. But there should be no need to activate the fan outside of the temperature parameters of the thermostat switch. The only purpose for the switch I installed was to prevent the fans from running, not to override the temp switch. And as I stated in the video, this will actually be controlled by the Holley dash in the future so that switch is only temporary. It’s basically doing the same thing an ignition switched 12v would do.

@@jamesscarberry3128 Just FYI, the fan only draws 5.3 amps and the temp switch is rated for 15amps. Derale doesn’t even recommend using a relay at all for this installation. The only reason I used one is because I didn’t want the extra draw on my ignition circuit. Here’s a link to the instructions if you need more clarification on wiring other than my video or still somehow think I’m not giving the correct information. 😉 derale.com/product-footer/product-instructions-footer?download=101:13900&start=100

Years ago I had so many people getting triggered over me not lining up my fittings that I do it on purpose now just to fuck with people. 🤣👍

@@BadLuckGarage lmao well keep doing good man cause i refrence your channel for alot of shit so definitely keep the jokes coming and the good work😂😂😂😂

Will do brother! I can’t do it any other way!🤣👍👍👍

LMAO! I know right?🤣👍

😅👍

Soldering is always the best option and I generally do that here in the channel when it comes to sensitive permanent electronics. If you watch more videos on this car you’ll see we’ve actually moved this cooler several times now. It’s currently in the back of the car. Lol

This cooler IS a stand alone cooler and has done excellent job on this car for over 3 years now, even with this car making over 900hp and running mid 5s in the 1/8. Take your nonsense elsewhere bud.

Hi Richard Scarlett! Thanks for watching. Glad this video helped you out!

@@BadLuckGarage 🤣👍

Sorry about that brother. lsxinnovations.com/product/6an-transmission-oil-cooler-adapter-fittings-gm-th350-th400-700r-4l60e/

@@BadLuckGarage thank you 💪