DIY 3D printed pinball machine - Testplay with Controller & Sound- Part 6 

Hi, thank you 🙂! Here is the Video of the final Pinball - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Sgq4DvL_ENM.html all my Pinball Videos you can find here - www.youtube.com/@fabe1690/videos and if you like to rebuild some parts, i provide them there - cults3d.com/en/users/wilfriedfabian/3d-models

Thank you! Yes it is a Replica of the Williams Spaceshuttle. Here is a Video of final Machine ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Sgq4DvL_ENM.htmlsi=cNUQFCCiwbqSofBC Regards, Fabian

THX!

THX!!

Thx!

THX!

Hi, the Ball has 21.5mm diameter, the playfield is ~1000x500mm, greeting, Fabian

Hello Simon, sooner or later i will share the Files on cults, probably it will be later. Because when i share STLs i provide usually an electronic circuit example for operating the specific Pinball Part . Even the Spinning Target in terms STL are quite simple, the electronics are not - so i need time for preparing and documenting this. However, pass me your email and i will send you the STLs. For the Target i use TCST1103 Photoelectric barrier sensor, On the side there is a "half" wheel attached to the axis of the spinner, this will trigger the sensor on/off each time the spinner turns. For the wav trigger implantation see Bobs instruction - it helped me a lot! www.hackster.io/BobB/pinball-sounds-and-music-bac92b Good luck with the pinball construction! Greetings, fabian

@@fabe1690 Thanks for that, I've just sent an email. That's actually the sensor I was thinking about in conjuction with a type of a 'wheel' with holes that is added to some of the arduino car toys. I did follow bob's tutorial already and have the trigger implemented

Hello, yes that are original Sounds from the Willimas Space Shuttle, my machine is a 100:70 Scale model of it. Greetings, W. Fabaian

@@fabe1690 Nice approach that you have taken. Plenty could find space for a reduced size pin table, but a full size machine could be problematic for some households.

Hello Rafael, i will provide some assemblies on Cults, but i need time to do it. Providing STL on Cults is quite work intensive, because the most of the assemblies will need an instruction manual. I will go ahead and will start with the Slingshot. I let you know when its online. Greetings, Fabian

@@fabe1690 Thank You .... I will continue to wait patiently but there are no problems ... I appreciate it I would like to show you what I have done ..... In fact, your bumpers work very well with the solenoid that you advised me, but since I had problems with the microswitch, I modified the upper part and put some sheet contacts and it works very well.... it looks great....

THX! i do not use the same for Bumper and Flippers. The one for the Bumper ("JF-1038" ~3A at 30V) was to weak for the flipper. I used a stronger type called "KK-1039B" (~5A at 30V) and for each Flipper i had to use 2 Pc! Greetings from Vienna.

@@fabe1690 Many thanks, I bought your bumper design and is very nice and well documented.

Thanks! I do already provide some STLs on Cults3d, In the moment im in the process to provide the Flipper STLs. Check out from time to time my Cults page cults3d.com/en/users/wilfriedfabian/creations Regards, Fabian

Lo puedes encontrar en Aliexpress

@@KaLiDEM Hello, yes you can find it on AliExpress and somtimes at Amazon as well. Here ist the link to the one i use in the Bumper : de.aliexpress.com/item/32365551790.html?gatewayAdapt=glo2deu and this one i use for the Flippers : de.aliexpress.com/item/32365820918.html?spm=a2g0o.order_detail.0.0.271663687b6ih9&gatewayAdapt=glo2deu i use the 12V rated types.

sorry - that anwer should go to Rafael

Hello Theo, i use per Flipper 2 Pc. K-1039 Solenoids, i need to supply it with ~30V to have adequate power. But Anyway you need some protective Electronics even operated with 12V, first a general overheat prtotction -> watch this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-GWccjgqyEhg.html and PWN to keep the Flipper in the active position. Greetings from vieanna

here you can find it -> de.aliexpress.com/item/32365820918.html?gatewayAdapt=glo2deu&spm=a2g0o.order_list.0.0.21ef5c5fLjC14R

i use the 12v Version

PWN should be PWM -> pulse width modulation

Hello Rapahel, i just put the Big Ramp on Cults3D. cults3d.com/en/3d-model/game/pinball-ramp-nr-1 Greetings, Fabian

Muchas gracias ---- thank you .....

Hello, i think thats possible. What Pinball did you think off? Greetings, Fabian

Danke!

Freuen *

Hallo, Hugobobo bin natürlich an deinem Flipper interessiert, hast einen link wo du deinen Vortschritt postest? Grüße aus Wien!

Hello Harry, yes - just post your question here, regards Fabian

@>>Fabe

@@harrylala8373 Hello Harry, well thats a quite genaral question. i have some tipps for you how i startet: .) dont put yourself unerder pressure, it took me 2,5 Years for a quite simple Machine from the eraly 80s. Atteack from Mars will be much more challenging .) start with a proto Type, where the aproach is "trial and error" .) Start collectin the knowledge you need: x) 3D Printing/Cunstruction was the esiest part x) you need electronictsknow how, get familar with LT Spice (electronics simulator) and Eaqsy EDA (PCB Production) for Eledctronics. x) You need to make Stickers - you will need Vector Graphics programm knowledge - i used "Inkscape" x) As Cad i used "Tinkercas.com"

.) also you need programming skills, is unsed an Ardunio Mega, i didn't use any "ready to go" Pinball Borads or Pinball Libarys for the ardunio. To speed up, i reccomned to use some parts i provide via Cults3d -> that would speed up a lot your building process (i do not only provide the stl files but also sample electronics circuts). if you like to get in touch via mail - pls, see my channel info -> www.youtube.com/@fabe1690/about STLs you can find here -> cults3d.com/en/users/wilfriedfabian/creations regards, Fabian

@@fabe1690 thank you very much >>Fabe