DIY 4 Tire Inflation System

Подписаться 1,1 тыс.

Просмотров 3,9 тыс.

50% 1

In this video we demonstrate how to build a four tire inflation system to facilitate in the air down and air up process when off-roading. Thanks for watching please like comment & Subscribe thank you :)
Harbor Freight 20% coupon: go.harborfreig...
50ft Air Hose: www.harborfrei...
Tire Chuck with lock lever x 4: www.harborfrei...
Barbed 3/8 fittings x 6: www.harborfrei...
Coupler x 1: www.harborfrei...
Quick connect x1: www.harborfrei...
Psi gauge x 1: www.harborfrei...
T connected x1 : www.harborfrei...
Valve /lever x1 : www.harborfrei...
Teflon tape x1 : www.harborfrei...
Barbed T fittings x1 pack of 3 : Joywayus 3/8" ID Hose Barb... www.amazon.com...

Опубликовано:

17 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@evansautomotive307 2 года назад

1/4in hose should be perfectly fine for this. The reason is, the shrader valve is the limiting factor when inflating and deflating. Unless you remove the valve core, the valve will be the bottle neck. So save a bit of money and get the 1/4in. In the end its up to you. I am going to build a kit with 1/4in and post a vid fairly soon. great video bro.

@roughpatchroad 9 месяцев назад

OK, that’s great to hear. And thank you

@tidalrootsadventures 3 года назад

Yeah I did a two tire and had the issue of pressure not completely equalizing but like you said in one of the comments that it’s only like 1-2 psi. Great video dude! Keep it up!

@roughpatchroad 3 года назад

Hey thanks brotha! And yeah just watch your Video. It’s a fun little project

@tidalrootsadventures 3 года назад

@@roughpatchroad true and it’s cheaper than buying the $200 + one. I appreciate the view!

@MrAndres722 3 года назад

Great video

@roughpatchroad 3 года назад

Andres Andujar Thanks brotha 🤠

@bradstevens993 3 года назад

😂 those cutters were frustrating me

@roughpatchroad 9 месяцев назад

Big-time 🤣

@roughpatchroad 3 года назад

Watch Vid at 2x speed! Pause and playback when needed

@malfunction6993 3 года назад

3/8 is smaller that 1/2 dude. Sorry to correct ya.

@roughpatchroad 3 года назад

Ahhh the old mistake. Thank you for the correction. Meant1/4* Thanks for watching 🙏🏽

@IFHSP2 3 года назад

Was thinking the same thing. Had to play it back...lol.

@IPinoyBoy69 3 года назад

Great video , will be doing this for sure. Definitely a great way to save some money. How is it holding up and would you change anything about it ?

@roughpatchroad 3 года назад

Jm92 Hey thank you kindly, not much but I would swap the chucks with a haltec lock on air chuck. Thanks again for watching 🙏🏽

@lloydboone7185 3 года назад

Do all the tires inflate and deflate at the same rate ? The one gauge is good for all four tires ? I’m sure there’s some physics involved that I’m not sure about. ( I’ve never taking physics 😔)

@roughpatchroad 3 года назад

Lloyd Boone For the most part they do deflate at the same rate. Occasionally the psi from tire to tire will be off by 1-2 psi. Thanks for watching

@lloydboone7185 3 года назад

@@roughpatchroad thank for your response. I will give it a try 😊