Тёмный

DIY CNC Plasma Table Build First Run 

Guy Stuff Workshop
Подписаться 226
Просмотров 16 тыс.
50% 1

This is the first run of my DIY Plasma table.
The links below are Amazon's links. I do get a small kick back from the affiliate links. I appreciate all of you for watching the videos.
Links Below
Stepper Motors amzn.to/48H4JNW
Crimping Tool Kit amzn.to/4569Khn
Lotos Plasma Cutter amzn.to/3s22Xqr
Lotos Supreme LTP7500CNC Plasma Cutter amzn.to/45rq4ZV
HGH20 Linear Slide Rail amzn.to/459fkjb
Pneumatic Chamfering Machine amzn.to/3OVjRA7
18/4 AWG Shielded CNC Wire amzn.to/3scjA2U
VEVOR NEMA Steel Enclosure, 20 x 16 x 10'' amzn.to/47oTtWu
7-1/4" TCT Saw Blade amzn.to/3P5Y9tv
Welding Helmet amzn.to/3OTCdl4
Stainless Steel Brush amzn.to/3qwYFXL
Power Supply amzn.to/3KHGc1E
Limit Switch amzn.to/3L3oxBR
Shaft Coupling amzn.to/45bkfQS
Stainless Steel Spray Paint amzn.to/3quwyIH
Knotted Wire Cup Brushes amzn.to/3sbnqt8
Wire Brush Drum amzn.to/3DZ5Yux
Cast Iron Welders Clamp amzn.to/3YCDd0k
Ballscrew Kit amzn.to/449Bm3Z
Power Supply 5V, 10A, 50W amzn.to/3qo0UNb
DC Brushless Cooling Fan amzn.to/47A0rs2
Relay Module amzn.to/44eaXlE
Cable Wire Carrier Drag Chain amzn.to/3YBd1CX
E-Switch amzn.to/47tZ0LA
Aviation Plug Connector amzn.to/45x9iJb
Arduino amzn.to/3Oz86Oy
Wireless Bluetooth Transceiver amzn.to/3Oyx0xO
EAGWELL 48V 1200W DC Power Supply amzn.to/3DZ67y5
Stepper Motor Driver, DM556 20-50V DC 5.6A amzn.to/3YB3Suj
Linear Guide Rail HGR20 1500mm amzn.to/3qxok2C

Опубликовано:

 

29 ноя 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 17   
@tjs_welding_and_fabrication
@tjs_welding_and_fabrication 3 месяца назад
I always clamp the work lead to the part. I made a small c clamp for this. Getting torch height control dialed in is always challenging.
@DazFab_Metalworks
@DazFab_Metalworks 5 месяцев назад
Thats an impressive first run, Nice cuts.
@guystuffworkshop
@guystuffworkshop 5 месяцев назад
Thanks!
@ChrisLocke1969
@ChrisLocke1969 3 месяца назад
lol pretty sure the water is sharing the ground with everything, never mind the rails ;)
@markyu70
@markyu70 5 месяцев назад
Great job!
@guystuffworkshop
@guystuffworkshop 5 месяцев назад
Thanks!
@markyu70
@markyu70 5 месяцев назад
@@guystuffworkshop I want to put plasma torch (100A) on my machine. I am making thc by myself. I want to make water bed and just put it on my cnc. What material do you used for water bed is it inox or something special, how tick is material, how deep is bed? Thank you.
@guystuffworkshop
@guystuffworkshop 5 месяцев назад
@markyu70 I made the water pan out of 3/16" mild steel plate and is 4" deep. Mostly because it was material I already had. I did coat it with 316L stainless steel spray, similar to "Steelit".
@dough6393
@dough6393 4 месяца назад
Nice work!
@guystuffworkshop
@guystuffworkshop 4 месяца назад
Thanks!
@ItsJustJake97
@ItsJustJake97 Месяц назад
What was the total cost of this table? Looks good
@rickhoey4843
@rickhoey4843 Месяц назад
Nice work! Are these your plans or some one else's
@gorunmezbiri4176
@gorunmezbiri4176 3 месяца назад
yüksek voltaj teknolojisi az kullanılması gereken televizyondan metal sektörüne geçmiş olduğunu düşünürsek buradan daha nelere geçer bilemiyoruz tabi fakat televizyonda hoş bir etkisi olduğu zamanları göz ardı edemeyiz şimdi boyle bir şeyi kimse tercih etmek istemiyor metaldede böyle bir etki zamanı geçmiş olabilir bir kaç tane de eurodancer vardır olabilir.
@The_VFX_Guy
@The_VFX_Guy 5 месяцев назад
Nice build. Do you have any resources/info on how you set up the electronics?
@guystuffworkshop
@guystuffworkshop 5 месяцев назад
I used the Myplasm controller. I used nema 34 motors, dm556 drivers, 48v power supply, and 5v power supply for fans. I was considering doing an overview of the table for my next video. You will need to match you motor drivers and power supplies based on your stepper motors. I put some affiliate links below.j amzn.to/48m8J6q amzn.to/470zCLZ amzn.to/3v2aib5
@The_VFX_Guy
@The_VFX_Guy 5 месяцев назад
Awesome!! Thank you very much. Definitely interested in your breakdown video as well
Далее
DIY CNC Plasma Cutter for 300$
20:27
Просмотров 18 тыс.
100❤️
00:20
Просмотров 7 млн
ATEEZ(에이티즈) - 'WORK' Official MV
03:15
Просмотров 14 млн
DIY Welding Fixture Table Build
14:42
Просмотров 1,3 тыс.
CNC Plasma Table Upgrade
11:14
Просмотров 154 тыс.
My DIY CNC plasma
22:55
Просмотров 2,7 тыс.
DIY CNC Plasma Table Based on JD'S Garage plans
15:43
Просмотров 121 тыс.
Junk-built CNC Plasma Cutter Table
13:45
Просмотров 87 тыс.
Budget DIY CNC Plasma Cutter || Adding a Rotary Axis
15:13
We build a CNC Plasma Table
31:35
Просмотров 11 тыс.