Hello friends, in this video i'll be making a high precision drilling tool. It's easy to do and the results you get are precise. You can find the measurements and material names at the end of the video. Hope you like it.
If you use the hole saw to scribe a circle where you want a hole then remove holesaw and with a 3/8” drill 4 holes roughly equally spaced then use hole saw to finish drilling hole That way the saw , , shavings have a place to go and while not clog up the saw teeth and burn the wood. Beautiful build, it is helpful to understand the build when you focus on the component.
11 месяцев назад
Great idea my friend, thank you for sharing your knowledge with us.
Mal wieder eine prima Vorstellung durch den Chef 😅leichte und verständliche Darstellung -aber das beste ist immer noch das die "Nachvollziehbaren Bauzeichnungen hier überlassen werden" Einfach nur Klasse ⭐⭐⭐⭐⭐
Como sempre, projeto maravilhoso, já estou com a oficina cheia de ferramentas baseadas em seus projetos e todas funcionando. Obrigado diretamente do Brasil.
That's cool - I often grab a bit of scrap wood and use a square and knife to mark a precise 90 degree line. Then I saw down that line chisel off the waste leaving an L shape that I use to align my drill bit. Takes about 2-3 minutes to make and it's always spot on 👍. If I need an angle I do the same but with a sliding bevel to mark out the cut lines
Muito TOP esse projeto de suporte de furação. Parabéns pelo trabalho. Ótimas dicas. Ótimo domingo. Abraços brother. Falando de São Paulo Brasil. 🇧🇷🇧🇷🇧🇷🇧🇷👏👏👏🤘👊
Por que a broca fica tao perto da coluna, caso precisace dum espasso maior nao teria , por todas furadeiras sao assim, eu penso que este espaco poderia ser maior.O brigado pela aula, bom dia 19/07/2023 as 09:30h . RJ- cascadura. Parabens.
Kardeşim merhabalar emeğine sağlık, videolar öğretici ve örnek. Bu arada bir şey sormak istiyorum; videonun 1.20 saniyesinde kullandığın freze güçlü ve kaliteli bir alete benziyor ama üzerinde hiç marka ve model hatta renk bile yok, markası nedir? yurt dışı ürün ise ticaret sitesinin linki var mı? Şimdiden teşekkür ederim, kolay gelsin.
6 месяцев назад
Teşekkürler Bülent Bey, videoda gördüğünüz freze Makita DRT50 model akülü frezedir. RT0700c modelinin akülü versiyonudur.
I wonder how much more accurate this is than a Chinese made 'drill locator' device that does exactly the same thing that's available on Amazon right now for $16.58?
11 месяцев назад
Man they're just garbage, play in their bushings and chucks.
This video is well done but I see a problem in the future. The throat is not deep enough. If you need to work with a 12 inch board or a 4x4 the precision feature will be lost when you have to place the guide on top of the workpiece.
Tüm malzemeleri almak elbette daha kolay ama satın almanın videosunu çekmezsiniz ve çekseniz de kimse izlemez. Burada usta her malzemeyi kendi üretiyor ve üretim videolarını gösterime koyuyor. Satın aldığı malzemelerin videosunu göstermiyor aklı kıt dostum.
Plus you miss out on the joy of lugging a full drill press to where you're working so you can drill vertical holes. It builds your muscles to lift that drill press up and hold it against the wall to get your holes drilled.
один только вопрос , если ут ебя есть оборудования и умение для изготовления этой шляпы и с ним обращаться , нахуна тебе эта шляпа ? я не поверю что с таким опытом в ручную будет погрешность несовместимая с жизнью . мне кажется эта хня должна полететь в космос
Вот если бы он эту шляпу смастерил и песка, говна и палок, при помощи каменного топора и палки-говномешалки, тогда все посмотрели бы и все, пара лайков и ноль обсуждений😂
@@Leichtinn глупость в чем? Согласен на ошибки, но чел, высшее техническое, не гуманитарное, и приблуда даже на " нормальную точность" не катит, не то что "повышенная точность".
@@iga00001 "..но чел, высшее техническое, не гуманитарное..." Не стесняйся,не шифруй,что сказать-то хотел.Ты в руках дрель-то держал? Попробуй просверлить несколько вертикальных отверстий вручную и с помощью этого приспособления.Потом измерь вертикальность угломером и сравни.Кстати,ведь не напрасно подобные стойки для дрели есть в продаже в столярных магазинах.
@@Leichtinn 🤣🤣🤣 стойка,столярка😅🤣, у меня токарка своя, из сверлильного обородувания предпочитаю 2М112, или при помощи ЗБ токарного, у нас с тобой разные понятия о точности, я предпочитаю " до сотки", а отклонения по вертикали "до минуты" стойка бля....😂
@@iga00001 А что сначала ни словом не обмолвился про свои высокоточные станки?С них надо было начинать и с ними сравнивать эту стойку. Руки что ли дрожали и в голове туман был?Ты хоть знаешь,что такое точность со своими тремя классами?Понятие о точности у него, блин... 😂