DIY Home Automation using ESP8266 & Blynk || IoT Project 

Best robotics channels for beginners on RU-vid

You're an amazing fello. followed so many tutorials out of my depth without success. Followed yours once and have it working perfectly! Thank you very much.

Your the best Indian tutorial guy I’ve ever seen

Wow great project, thanks for the ideas! Now I know what to do with all those old ESP8266 01's I have laying in my drawer. Back when they came out, I had a blast playing around with them but quickly switched to the more modern until the wonderful ESP32 was developed. Now I have them all over my house in the form of cameras, and wifi radios as well as using some of the esp8266's to drive MP3 Players and such with the VS1053 versions. The VS are a bit spendy, but they make some great audio devices out of Arduino's and ESP's.

Nice job on the PCB WiFi relay board!

I really liked the vid and how clean it was. I actually would have liked an explanation for all the parts and why you were using them. but it was very informative. Thank you!

Wow your awesome man! Hey I didn't see the Blynk code in your video description....can you please include this?

thank you great video:) efter I receive the Token from the app (by e-mail) it works. The io 0 must be in short circuit to be able to program it, and to run it, disconnect it and short circuit the +3.3v and EN to make it run

Nice project and useful tutorial 👍.

Gracias, muy bien explicado, un cordial saludo desde Mar del Plata, Argentina.

Your project inspire me , thank you

Nice job buddy

please, help me! Upload failed, error: Sketch uses 268640 bytes (53%) of program storage space. Maximum is 499696 bytes. Global variables use 30680 bytes (37%) of dynamic memory, leaving 51240 bytes for local variables. Maximum is 81920 bytes. warning: espcomm_sync failed error: espcomm_open failed error: espcomm_upload_mem failed error: espcomm_upload_mem failed

What capacitors do you use? 0.1uf 25V? 100uf 25V? Thx

What happens when android device or app stops or terminate by user?, is it still keep the light on or off when android device is offline?

You can easily purchase electronics components from Mouser. Don't need to Desolder.

thanks for this tutorial. I will need the relay only to close for 2 seconds then open again. Will the code change a lot from yours ? It is for a street door opener project

Is it possible to connect IR Sender and control the TV using this ESP ?

Great presentation!

i think the heat gun lamp is cool. thank you.

Nice project

"how to fix for error compiling for board" anyone can help me, please?

is there a way to turn on the lights with a switch, when the internet is down?

Very Good

You said to have separate oversupply when you were working on breadboard , but after the PCB you had only one power supply .How and why?

Hi, I have a question. can i power up a 5 volt 4 channel relay module with a 5 volt 0.7-0.8 mAh wall type charger, which is basically use for charge the simple mobiles. If yes, then how i connect, i mean what will be the circuit diagram. which wire will be connect with the vcc and which wire connect with the ground and which wire is connect with the ESP8286. OR, ESP8266 nodeMCU board 3.3volt is sufficient for 4 channel 5 volt relay? i am try to built a home automation project. Thank you very much. Please help me

ESP8266 is not connecting to the Wifi network, hence not visible over the Blynk.

Very good project!)

Is possible to command it with alexa?

What capacitors did you use? Not visible there.

The problem I met with Esp01 when first boot up and delay in High status, ESP will discontinue boot, how can fix it?

Is it possible to use the lamp current to provide the voltage of the Esp instead of having an external supply ?

will you provide ready made project ?

can you pls make a video on how to make that cool glue gun lamp

Where i can download library of esp8266

ESP8266 not showing online in Blynk App..Please advise.

Why do you not reply to questions posted below??????????????????

Where to download the esp library?

can you sell this PCB ??

Heyy bro ...remember me???

Có code cho module này ko bạn

Bro diagram

Pls make a video on how to make that glue gun lamo.........pls pls pls!!!!!!!1

It can only control 2 device...but it have more gpio

👏👏👏👌

Hi I like your project.can you give me Sketch of project or code plz.if yes send me in my inbox.or give me the link for download.

hi, thenk you for video. may be send gerber file

plz send me code

AC ??😂😂🤣 i have a remote control only for LG AC

How did you get sponsership

Your pcb design is awful!

why do you try to speak in American accent? Pls don't do it.....