DIY: How To Build a Fork Mount Bike Rack for $20 in 30 Minutes

Подписаться 18 тыс.

Просмотров 292 тыс.

50% 1

Do you need a way to transport your bike but don't feel like shelling out hundreds of dollars for a hitch rack? Well, look no further because I've got a solution for you that's quick and requires only a few common tools. This rack can be used in any pickup truck bed and in most SUVs.
See this project on Singletracks:
tinyurl.com/bu...
For this project you'll need:
1 piece of wood (ideally a 2x6 or bigger)
1 1/2" floor flange (per mount)
1 1/2" tee fitting (per mount)
1 1/2" nipple fitting (per mount)
2 Close PVC risers (per mount)
4 wood screws (per mount)
Tools required:
A saw (if the wood is not pre cut)
A drill
A tape measure and a writing utensil
Pliers (optional)
The rack I built with two mounts cost a total of $21.37 for the finished product. If you have common materials laying around the house (like wood and screws) and only need a single mount you can easily get away with building this setup for $10. Check out the video for detailed instructions on how to set this rack up!
Rock Angel by Joakim Karud / joakimkarud
Creative Commons - Attribution-ShareAlike 3.0 Unported- CC BY-SA 3.0
creativecommons....
Music provided by Audio Library • Video
Follow us at Singletracks:
On the Web: www.singletrack...
Facebook: / singletracksmtb
Instagram: / singletracks
Twitter: / singletrackscom
Get Merch:
shop.singletra...

Спорт

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 152

@eddy7680 4 года назад

Everything worked out great. I built it right away. The only issue I found, was that the axel was not well supported due to the difference between the inside diameter of the plastic nipples and the axel itself. I also found the plastic was a little weak and the forks would pop out with a little twisting. I took a wooden dowel, pressed it in and drilled a hole through the middle. Now the axel has no wiggle room and is supper sturdy. Hopes this helps anyone with their project and thank you for putting up the video.

@trust5977 2 года назад

Please excuse my ignorance, but when you say drilled a hole through the middle of a wooden dowel do you mean lengthwise? If so, what sized drill bit did you use?

@DIYManiacJohnP Год назад

Attach t-mount to flange first and then mount flange to wood. This will ensure a tight connection of the t-fitting and also ensure that the fitting is properly aligned

@genso3065 4 года назад

I was looking for a fork mount to put on a 2x6 which is just 17$, but for one fork mount. Then I searched a diy and came upon your video. I'm stopping by home depot tomorrow. Haha

@everettbateman5864 3 года назад

Just ran up to my local hardware store and got everything for my full suspension and dirt jumper!

@joshwiegand 2 года назад

This is a great idea, I built one so I can store 2 mtbs in the back of my van under my bed. I guess the thing I wished I had done was to make sure the pvc nipples would fit the spacing of my fork as well as my thru axle. For the latter just bring your axle with you to Home Depot. Not trying to be a hater, just trying to save someone some hassle. Thanks for the great idea!

@singletracks 2 года назад

Great tip!

@trentay56 5 лет назад

Fantastic! Perfect for my pickup. Will adapt for thru axles

@karstencostain5640 4 года назад

Thank you so much😂I almost just spent around 50 on a mount, love it👍🏻

@artravision 5 лет назад

Home depot will cut the wood for you. Great video!

@jeremydubrulle6686 4 года назад

Genius! Thanks so much mate ! Built my own thing way cheaper and way more fun!

@jojorice4594 2 года назад

Happy to Have It!

@LonnieWormley 3 года назад

This is a great idea for my band build thanks a lot

@rodrigomazzola 7 лет назад

Just saved me 250 bucks! ty a lot!!!!

@funtivitycolton1930 7 лет назад

No problem! I'm glad you liked it!

@dansuchy42 3 года назад

Thanks for the awesome idea and great step-by-step instructions! Just finished one for my van today - it holds my two road bikes securely and looks nice!

@kristyburchard3320 3 года назад

Fabulous! Building one this weekend.

@otarigabunia1078 3 года назад

HOLY-MOLY! YOU SAVED MY DAY!

@zackaguilar5004 4 года назад

Made one last night works fine I'm also going to strap down the bikes after they're mounted for a extra secure ride. I think I'll get some extra quick release's to keep on the mount for the ease of not having to switch it back and forth.

@gslife1 4 года назад

Great video, just what I was looking for. Some of these comments below are unbelievable. Thank you for sharing this great idea.

@HWG-wm8ld 4 года назад

Yes, there are some real winners. One guy complained about the sound, as if Cameron Crowe is the director...dics

@boltman01 3 года назад

Great video. Love all the haters who just feel the need to leave negative comments 😂 If you don’t like the idea or can’t figure it out, move on and do something yourself.

@blumenpedaler9516 3 года назад

This is awesome! Thanks for the video!

@michaelmeier310 4 года назад

Fantastic! I had my doubts going into this but it worked out great! 👍

@JamesRobertMTB 6 лет назад

This is such a rad idea

@mysho6317 6 лет назад

Thanks for Video & DIY solution........still fine tuning to match my needs but Your idea is the star of the show. Thanks again

@anthonytiburcio9260 3 года назад

Great video!

@whutdatytopsy9651 4 года назад

That looks awesome!

@okioki1131 6 лет назад

Im in Colorado too, good vid!

@jvcardesign 4 года назад

very cool. This gives me some ideas.

@rickc2222 7 лет назад

Awesome, I'm doing this for a cheap single hitch mount....

@vladimirkocurek 3 года назад

PERFECT!

@user-ik9gw4wh4c 3 года назад

I thought your idea was great I brought all the components, being in Germany it cost me three times as much plus I had to bore the center of the PVC raisers out by 2mm and shorten the by 3mm to fit my 15x100 front axel. But hell it’s original.

@opinion5072 2 года назад

Excellent video man really like the part where you lay out the prices thanks.

@singletracks 2 года назад

Thanks for the feedback, glad you like it!

@messerole 6 лет назад

I am making this today. I have a 15mm boost. The 1/2 plastic nipples are not big enough for the axle to slide through. I bought the 1/2 set like you said but with the two nipples that hold the through axle being brass not plastic. The brass nipples are a perfect fit but there're brass. Also the 1/2 nipples (close) are 1 inch and not wide enough for the boost setup. I got the brass ones in 1 1/4 and it is a little wide. Gonna have to file this one down. I also got the entire set up in 3/4 instead of 1/2 and it works great. I'm gonna keep the 1/2 one to show friends and or let them use it. Thanks for the video.

@iseeker3845 3 года назад

wouldn't the 3/4" set have a lot of play with a 15mm thru axle?

@kateharvath 2 года назад

Brilliant!!!

@singletracks 2 года назад

🙌

@matthewleone5250 4 года назад

Great video! Great idea! Any way to make this work for my two road bikes?

@rickc2222 7 лет назад

video was meant for 15mm axles - mine is 20mm or 0.787", so I need to use 3/4" pvc pipe which is 20.93mm - close enough…

@user-yv2cz8oj1k 4 года назад

Is sat go for 3/4 inch anyway and convert down for 15mm. Fashions change. You got a list together yet?

@ray59401 4 года назад

My 15mm axle doesn’t fit. Guess I should have went 3/4

@Dmasters95 3 года назад

Doesn’t fit my 15 mm and the 3/4 is way too big

@iseeker3845 3 года назад

i have a 15mm thru axle and it didn't fit through the 1/2 pvc. HOwever, after boring the PVC with a 5/8" spade bit, it did.

@usernamemykel Год назад

What "axles" did you use????????????????????????????????

@nickngaopraseut6717 5 лет назад

Yo that’s awesome!

@martineguay6475 6 лет назад

Hello! Thank you for this video... Very helpful. Can you please tell me the space between the fork of your bike. My Fat Bike is almost 6 inches between fork. Would this be ok for this size?

@funtivitycolton1930 6 лет назад

Hi Martine! Yes, you could still do this, just get longer pieces to insert into the T pipe :). It would technically work just the way it is but it will be more stable if you make it wider.

@keithc728 5 лет назад

That's nice. I only wish I still had my pickup

@hawkeyes2873 4 года назад

Very nice how many bikes can be accomodated

@richardsun9371 3 года назад

Great design. I am building an inside car bike rack using a fork holder. Does the rear wheel need to be tied down?

@toddanderson8277 3 года назад

Great idea but curious if your bike is older and doesn't have the front hub easy lock vs the older screw on/off nut what can you use to secure the fork down? I'm looking to secure four bikes and I think the 2x6 idea with staggered hubs will work.

@cdig4 3 года назад

The 1/2” PVC close riser Does not fit a 15mm through axel.

@aboutsean 2 года назад

For $27 you can buy a fork mount on Amazon and it's lockable! This seems like a solution to a problem that doesn't exist.

@singletracks 2 года назад

Good point! Some of the non-locking ones are as low as $20 on Amazon (and they only work with QR axles), though that's per bike mount so if you want 3 you're looking at $60-80+. For those on a very strict budget, black pipe still might be the way to go. Locking mounts from a reputable brand like Yakima cost $70 each.

@rockbouchard4891 3 года назад

What about a fatbike 150mm wide fork or 135mm wide ??

@theoldgoat4525 4 года назад

This is so cool, will it work with through axles?

@pbearzzz2939 5 лет назад

Brilliant!

@edzukation 2 года назад

never seen a 70% off cart - is that in all the HD?

@singletracks 2 года назад

I don't think so. Just depends on if they have items they really need to get rid of.

@johncb5865 7 лет назад

I guess for a boost set up, use different PVC fitting?

@funtivitycolton1930 6 лет назад

You got it! Pretty simple swap.

@misteryuz19 3 года назад

How about roadbike fork mounting? Is the size same?

@MichelBakhos 7 лет назад

Thank you thank you

@funtivitycolton1930 7 лет назад

No problem Michel! Glad you liked it.

@cjones9058 3 года назад

Any experience with the $15-20 fork mounts available from Amazon, etc, compared to this DIY option? Maybe those break easier? Or are the PVC nipples prone to breakage at all?

@mailloux093 4 года назад

Does not fit 15 x 110mm axle

@jeremyfranks9587 6 лет назад

How much was the quick release?

@diegudr 3 года назад

How to you keep the 2 x 6 from moving front to back? Or is that not an issue?

@rodneydives7385 2 года назад

can you make this kind of thing for a roof rack with cross bars?

@singletracks 2 года назад

That could be tricky, but not impossible. You definitely want to make sure it is secure! Saris has a pretty cool modular system for truck beds that can also work inside an SUV. It's pricier than DIY, but looks a bit more polished. www.singletracks.com/mountain-bike-deals/?q=saris+traps+single+track

@miguelcintron6595 4 года назад

That work for Axle thru, not for Q.R.?

@aliscia70 4 года назад

grazie amico mio mi hai fatto risparmiare un mare di euro

@ahmedranderee5315 6 лет назад

what would i need to get to adjust this to a road bike?

@rnfaboy 2 года назад

You didn’t mention where you got the fork mounting rods that hold the forks to the rack

@singletracks 2 года назад

If you mean the 'rod' with the quick release lever that slides through the pipe/rack hardware, that's just the thru axle that comes with your fork. It's the same one the wheel rolls on so you should already have this!

@rnfaboy 2 года назад

@@singletracks so when you take your wheel off you just remove the thru axle bolt and use it for your mount. Thanks.

@singletracks 2 года назад

@@rnfaboy Right, when you remove the axle to take the wheel off, slide it back into the fork to secure the bike in the rack mount. This also helps you avoid losing the thru axle, which definitely can happen!

@clenilma100 Год назад

I was very nervous putting my brand new beach cruiser on this rack. ru-vid.comUgkxG6JIgwJhur8_Rg8UeQ3EmePzi_wSncL8 But after reading many reviews I decided to get this one and take a chance. When arrived it was very simple to adjust and put together. I also added spike tape over the metal hooks before securing and tightening the straps, and no scratches. I also purchased the top bar made by the same company so that my cruiser sits straight on the rack without having to turn upside down. Extra bungee cords are used to secure the front wheel from flapping and even piece of mind knowing your bike is secure. Definitely recommend...

@davidrowe8747 3 года назад

Does this work only for through-axles? I didn't realise until the very end that this is for through-axles (maybe not for QR?)

@iseeker3845 3 года назад

Yes. But, I'm thinking of just using a block of wood and drilling a hole through it for my son's quick release

@just4all1 4 года назад

i got the bike, and i got the stuff for the rack, now all i need is a truck

@paulysci925 6 лет назад

used they're like $30 on Craigslist and you could spend the 30mins driving to pick one up?

@paulysci925 6 лет назад

oh i see through axle compatibility because of through axel being the standard now. i forgot because i still have qr. this would be handy if i keep my bike may ride it another year and go through axel for future ease of compatibility.

@trevormick2248 5 лет назад

Will this work for boost forks?

@locoboy23 5 лет назад

Hello ! Thank you so much for the instructions! I know this is an old post, but I have a Trek FX3 Disc, according to Trek website mine is: Wheels - Front hub -Formula alloy, 6-bolt disc, 12mm thru axle, 32h Do I use the same size as you? Thanks!

@Maccaroney 5 лет назад

Nope. MTB have bigger axles by a few mm. You and i have 12mm diameter front axles whereas this guys' MTB is probably 15mm or so. I recommend taking your axle into your local hardware store and just looking for fittings that fit snugly and build from there.

@c71chung 3 года назад

1/2" is 12.7 mm, so 12 mm would fit not 15mm tho.

@JA-gx4hb 4 года назад

Could use more detail on how to attach bikes. Seems like a sudden stop would cause bikes to rotate up and slam into rear window. Please try it and show video.

@senglebe 3 года назад

the bike is long enough and enough of a counter balance that that shouldn't really happen, but you could run a strap through the rear tires if you're worried about it. I like this concept generally, but I don't like how loose the axles would fit. I bought an aluminum one of Amazon instead for around $17 a piece that is designed to fit the 15mm x 110mm axles of modern mountain bikes.

@alonzomartii 6 лет назад

So PVC nipple was .38¢ or .34¢? :)

@BlueOvals24 2 года назад

Great idea right up until the part where you have to remove your bikes wheel to make it work

@singletracks 2 года назад

Definitely not as convenient as a tailgate pad but depending on your truck setup this can be handy. It's incredibly secure as well.

@BlueOvals24 2 года назад

@@singletracks I'm sure it's solid. I'm thinking about getting a tailgate pad though, just not sure if it will work with my tonneau cover. I might consider a bike with a quick disconnect wheel, but I'm not sure if I want something that makes it even easier to get stolen.

@gregkosinski2303 5 лет назад

"first we're going to want to grab our wood."

@vzangla 4 года назад

check and check.

@jvcardesign 4 года назад

hahahahahahhahaha

@user-yv2cz8oj1k 4 года назад

I'll pick most of the parts up when I'm in California again. You don't want to know the prices for these parts here. 🤣

@nikkiesteban 5 лет назад

what is the size for 9mm qr?

@bduntz 6 лет назад

Where did you get the quick release from?

@brychli 6 лет назад

You can get these (cheap) on ebay.

@iseeker3845 3 года назад

it's not a quick release, it's a 15mm thru axle

@gilboston20033 5 лет назад

I dont see the bike on it. I have to give one star, lol

@rbd104 3 года назад

Or you can buy quick release mounts, they look better, are not much more in price and come with a skewer already.

@ibaher1 3 года назад

Where can I buy the quick release mount? Any link would be appreciated

@imemovengeance 5 лет назад

Does 1/2 inch pvc fit 15mm thru axles?

@swimpitt95 5 лет назад

No. I tried this with 1/2 for my 15x100 TA and axel does not fit through the plastic close risers.

@hornkid 4 года назад

Yes it is possible to make this work for boost with 1/2” pvc risers! I was able to make it work by boring the plastic risers slightly using a file. It probably added about 10 minutes to the job. It turned out great actually and has a nice tight fit.

@iseeker3845 3 года назад

I used a 5/8" spade bit to bore the holes slightly larger; we'll see how it holds up.

@tmfrs2 7 лет назад

All you have to do now is make the wood waterproof :D

@billj121 7 лет назад

Use decking material = waterproof.

@tmfrs2 7 лет назад

Ah ok, thx bill

@PeterHartman1 7 лет назад

Here is a $5 version that looks just as functional. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-QPQeCqre8pI.html . Just use plastic pipe and the metal straps and you should be good to go. The grey electrical pvc is uv stabilized if you want to skip the painting step.

@funtivitycolton1930 7 лет назад

Interesting build! Nice and cheap.

@Dmonieluv 4 года назад

Suh-weet!

@bodiless99 4 года назад

You could have added more detail (some, ANY) about how you attache the bike. #imanovice

@TTPHOTO_15 5 лет назад

I don't trust putting my through axle through that you might scratch it

@LV2XPLR 5 лет назад

The axle will only touch the plastic nipples. Its unlikely plastic would ever scratch the axle.

@edwardgarcia3731 4 года назад

That thing was trash.....didn't work! Bought quick release mounts with brackets on Amazon for $17! Done deal

@johnr8013 3 года назад

Yep! Glad I looked at the comment section, going to use his technique with the 2x6 board and carabeaners just not the pipe fittings.

@waitersluvhjy66 4 года назад

Woodprix is nice for that.

@nikolusmatthews8889 5 лет назад

What glasses are those?

@robertt251 5 лет назад

Viper

@danielsonhobbies 5 лет назад

$10 racheting straps from harbor freight or walmart will be easier and quicker. No need to disassemble front wheel. Same idea as tying down dirt bikes in pickup trucks.

@DROY2004 4 года назад

Here’s a pro- tip for you, get a wireless mic so we can hear you, sound is very bad! Shalom!

@ClayJ926 6 лет назад

What am I missing? Half-inch diameter is less than 13 mm, through-axle is 15 mm…seems like if I wedge the axle in it’s not coming out very easily.

@laidavid 6 лет назад

ClayJ926 I am wondering the same??!

@shredwithscott 6 лет назад

Just tried this and the PVC nipple is probably .5 mm too small. I’m thinking I’ll just run a 5/8 drill bit through them to enlarge it a bit. Now if only I had a 5/8 bit.

@shredwithscott 6 лет назад

The fittings are pipe thread, so a 1/2 NPT fitting only defines the threads and pipe OD, it doesn’t specify the ID. One table I found says 1/2” NPT is .622” ID, which is 15.8 mm, but the PVC fittings must be a tad thicker.