DIY Kids Kitchen Helper Tower! (Full Build)

Подписаться 4,2 тыс.

Просмотров 12 тыс.

50% 1

In this video I build a kids kitchen tower helper/ learning tower. I start with the cut list options and go through each step all the way through finishing.
Materials needed
1. 1/2 sheet of 3/4 inch plywood
2. 1 closet rod
3. 2x4 mdf sheet
4. 1 1/4 inch pocket hole screws
5. Pocket hole dowels
Contact Info
MaryleyJaxGarage@gmail.com

Авто/Мото

Опубликовано:

3 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@perfectdiversion 2 года назад

This is the simplest DIY helper tower on RU-vid. Thanks for this!

@MarleyJaxGarage 2 года назад

Thanks for watching and appreciate the comment!

@davidturner6436 Год назад

This is casual Build plans on RU-vid. I just finished up 2

@kahwaoupodcastdz Год назад

Thank you! That was very helpful. You're a good teacher

@AlvinC-sz3li 2 года назад

Don't know why this video has so few views. This is the most beginer friendly video I have seen on RU-vid, no fancy expensive tool needed.

@MarleyJaxGarage 2 года назад

Thanks man I appreciate that.

@AlvinC-sz3li 2 года назад

@@MarleyJaxGarage Followed your video, I made 3 with a 4x8 plywood, sold 2 on FB for $65 each, which covered my material cost.

@antonmpamies 2 года назад

congratulations you did very well and simple

@MarleyJaxGarage 2 года назад

Thanks man I’m glad you liked it.

@Mef637 Год назад

Very well done!

@MarleyJaxGarage Год назад

Thanks for watching

@tfwoodcraft 2 года назад

Nice work! gonna try to whip one of these together for my son this weekend. I like the short and to the point video without leaving out important stuff. (I definitely would have rounded over the edges before marking the lines for the steps, then would have had to guess a little bit where the line should go)

@MarleyJaxGarage 2 года назад

Thanks I love getting comments like these because it is one of the main reasons I started making videos. Too many people want to tell you their life story before telling you how to do what’s in the video title.

@davidcowperthwaite1159 2 года назад

I love the simplicity!

@MarleyJaxGarage 2 года назад

Thanks for watching

@FelipeMC0810 Год назад

Awesome vídeo

@ngoti8tor 2 года назад

Love the build, and I think this is one of the simplest and best learning towers on RU-vid. Do you have any measurements or plans that you can post?

@davidturner6436 Год назад

Casual build has the plans. He created this step stool.

@alisaoswalt1478 2 месяца назад

I am wondering about the step that they stand on. It looks like you used 3/4”. Just wondering if a 3/4” router bit is going to make an opening that is too wide so that the board does. It fit snug

@DannyTrandannyhaitran Год назад

Really enjoyed watching the video. I appreciate you splitting up the sections and getting straight to the point. Planning to try this out on the weekend! What kind of plywood did you use for this?

@MarleyJaxGarage Год назад

I used a nice sande plywood from Home Depot. It is just a little nice finish since I didn’t want to paint it.

@lucasblattenberger6066 7 месяцев назад

do you by chance know what the angle of the front of the side walls are? or the width of the side walls at the bottom and top? looking to build this this weekend!

@DrewPeabawls Год назад

I’m definitely going to try this build. I could figure out how deep the tower was top vs bottom since looks like one of the sides is on an angle. Any ideas?

@MarleyJaxGarage Год назад

I can't remember exactly I want to say it was 24 on the bottom and 18 or 20 on the top

@peacefulthinking387 2 года назад

has anyone found any plans for this build?

@MarleyJaxGarage 2 года назад

I never made any plans for this build. There are a lot of similar plans available or you can just make your own. I gave pretty much all the dimensions in the video. Let me know if you have any specific questions.